Body

This is for you folks out there who want the correct part number on your hinge. Good used OEM original hood hinges that are available individually or as a set. We now offer a PREMIUM quality reproduction that is superior to any other reproduction. We carefully inspect these hinges before sending them as used hinges are prone to wear in more than one area. Here is a helpful youtube video that shows you how to adjust your hood. Shipped with the spring. These will also work on 1967-70 as well....

Improved reproduction right and left hand hood hinges for the Mercury Cougar and Ford Mustang. Much heavier duty compared to the originals, thicker metal and slightly wider hinge bars. These hinges weigh 4.35 lbs, originals weigh 3.2 lbs. Hood hinge rivets have the 'plus' markings like seen on the 1969-70 hinges. Save your hinge springs, these do not come with the new springs. it will be easier to fit and adjust these hinges prior to installing the springs on them. We use an old section of...

Reproduction Non-Functional hood scoop that was originally used on the 427 GT-E, but will work on any 1967-68 Mercury Cougar and look great! This scoop measures 25 3/8" at its widest point, 26-1/2" at its longest point, and is 2" high. Originally, the recessed scoops in the front were painted black to give the illusion of an open scoop. The original blue prints show the center of the rear stud as being 2 1/8 inches forward of the back edge of the hood. Measuring the distance on original XR7-G...

Non functional scoop originally used on the 1968 Mercury Cougar XR7-G but will work on any 67 - 68 Mercury Cougar. This scoop measures 25 3/8" at its widest point, 26 1/2" at its longest point and is 2" high. The original blue prints show the center of the rear stud as being 2 1/8 inches forward of the back edge of the hood. Measuring the distance on original XR7-G and GT-E's most measure about 1 1/2" from the rear edge of the hood to the rear edge of the scoop at centerline. This differs from...

Welded in hooked retainer for the rear seat back installation on any 1967-73 Mercury Cougar or Ford Mustang coupe or hard top body style. This bracket welds to the edge of the package tray. Two hooks per car, sold individually. We cut out a individual sections as shown. Make good measurements prior to removal of your old brackets. You will need to drill out the spot welds prior to installation. For sure that basic Ford part number is 62118.

Used rear driver side (left hand) courtesy / opera light housings for the Mercury Cougar. The rear courtesy / opera light was standard on all XR7 Cougars, but were a popular option on decor and standard level interior Cougars. These units are marked LH for the driver side and RH for the passenger side and are sold individually. Also sold as a PAIR. Ford part # C7WB-13B729-C or C7WY13A744-C for the passenger side, C7WB-13B736-C or C7WY-13A744-D for the driver side. *TRIVIA* Did you know that...

Used rear passenger side (right hand) courtesy / opera light housings for the Mercury Cougar. The rear courtesy / opera light was standard on all XR7 Cougars, but were a popular option on decor and standard level interior Cougars. These units are marked LH for the driver side and RH for the passenger side and are sold individually. Also sold as a PAIR. Ford part # C7WB-13B729-C or C7WY13A744-C for the passenger side, C7WB-13B736-C or C7WY-13A744-D for the driver side. *TRIVIA* Did you know...

Used rear driver side (left hand and passenger side (right hand) courtesy / opera light housings for the Mercury Cougar. The rear courtesy / opera light was standard on all XR7 Cougars, but were a popular option on decor and standard level interior Cougars. These units are marked LH for the driver side and RH for the passenger side. Also sold individually, see related items. Ford part # C7WB-13B729-C or C7WY13A744-C for the passenger side, C7WB-13B736-C or C7WY-13A744-D for the driver side....

Full driver (left hand) side front frame rail measures 52" long and the outer rail has weld nuts installed for proper installation. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...

Full passenger (right hand) side front frame rail that measures 52" long and the outer rail has weld nuts installed for proper installation. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...

Reproduction passenger side front fender apron that has the shelf for installing the battery tray. *Restoration Hint* This section of metal was VIN stamped, consider welding in the stamped VIN section to keep your car whole.Here's a little film to help you fortify your flexxy feline!

Guide that measures 10 5/8" long held in place by the outer trim that has four screws. Driver and Passenger are interchangeable.

This latest of a series of 67 - 68 reproduction sheet metal parts is just what the market has been waiting for! This listing is for the framework of the hood. This frame is for someone who needs to replace the rotted out bits of your hood frame, or for someone who simply wants a base to make a fiberglass hood on their own.  These hood frames are oversized and cannot ship through UPS or USPS, so it will need to ship via truck freight. You can expect to pay somewhere between $200-300...

Quality inner wheel house made by Dynacorn patterned off of Grade A used panels provided by West Coast Classic Cougar.We also sell these as a complete set of four, which will save you money on shipping as we unbox them and nest all four together and fit them in one box.

Quality inner wheel house made by Dynacorn patterned off of Grade A used panels provided by West Coast Classic Cougar.We also sell these as a complete set of four, which will save you money on shipping as we unbox them and nest all four together and fit them in one box. ...

These interior door release handles are the only ones on the market from the 4 different manufacturers that are indexed correctly. They are the updated design for 2019 that fits level and the chrome is excellent. All the other versions either tip up or down too far when placed on the splines. These were used on the xr7 model in 1967 and on all Cougar / Mustang models in 1968.  The casting number on the back reads C7AB-5422617-A.

These interior door release handles are the only ones on the market from the 4 different manufacturers that are indexed correctly. They are the updated design for 2019 that fits level and the chrome is excellent. All the other versions either tip up or down too far when placed on the splines. These were used on the xr7 model in 1967 and on all Cougar / Mustang models in 1968. The casting number on the back reads C7AB-5422616-A.

Reproduction rear courtesy / opera light lenses for the Mercury Cougar. The rear courtesy / opera lights were standard equipment on all XR7 Cougars, but were a popular option many other standard and decor level interior Cougars. If your car did not originally come equipped with them, it is actually quite easy to install them, but you will need to purchase our used housing /socket assemblies. These are fantastic quality and a perfect fit. Sold as a pair only. Ford part # C6VB-13B726-A. *TRIVIA*...

Economy version of our Ignition / Door key. These keys DO NOT have the Ford logo.Replaces Ford #: C7AZ-6222053-A.

Little touches make a big difference. These blanks have the correct Ford script. Replaces Ford #: C7AZ-6222053-A.

Reproduction economy trunk / glove box key. These keys DO NOT have the Ford logo.Replaces Ford Part #: C7AZ-6243562-A.

Little touches make a big difference. These blanks have the correct Ford script. Replaces Ford Part #: C7AZ-6243562-A.

When ordering this item, you do not need to order a key blank, the key is included. If you need more than one key, you don't need to pay for multiple key cutting services, just buy extra blanks and mention it in the comment section of your order. This listing is for the ECONOMY version of the ignition / door key. We now have the ability and equipment from an old Lincoln Mercury dealership to cut keys for Fords "by the numbers". Instead of copying a worn key to make yet another key that doesn't...

When ordering this item, you do not need to order a key blank, the key is included. If you need more than one key, you don't need to pay for multiple key cutting services, just buy extra blanks and mention it in the comment section of your order. We now have the ability and equipment from an old Lincoln Mercury dealership to cut keys for Fords "by the numbers". Instead of copying a worn key to make yet another key that doesn't fit properly, we can cut keys as they would have come from the...

When ordering this item, you do not need to order a key blank, the key is included. If you need more than one key, you don't need to pay for multiple key cutting services, just buy extra blanks and mention it in the comment section of your order. This listing is for the ECONOMY version of the trunk / glove box key. We now have the ability and equipment from an old Lincoln Mercury dealership to cut keys for Fords "by the numbers". Instead of copying a worn key to make yet another key that...

When ordering this item, you do not need to order a key blank, the key is included. If you need more than one key, you don't need to pay for multiple key cutting services, just buy extra blanks and mention it in the comment section of your order. We now have the ability and equipment from an old Lincoln Mercury dealership to cut keys for Fords "by the numbers". Instead of copying a worn key to make yet another key that doesn't fit properly, we can cut keys as they would have come from the...

Zinc plated, visually correct copies of the original, very prone to failure... We highly recommend buying our good used latches linked here even though they may not look as pretty. No warranty on this low quality off shore part.Replaces Ford Part # C5AZ-6243200-ACheck out our video below showing how to easily remove and reinstall your 67-68 trunk latch, lock, and cover plate, and some info on getting a new key made. ...

During installation, check for proper alignment with trunk latch. Trunk latch and striker should engage smoothly, both items are adjustable. We only save the rust free latches with no wear or rust, the rest are tossed. Fits 1967-68 Mercury Cougar. Ford part number C6OZ-6543252-A.

Used grade "A" rear courtesy / opera light lens for the Mercury Cougar. The opera lights came as standard equipment on all XR7 Cougars, but were a popular option on decor and standard level interior Cats as well. These used lights are they very best we can provide, but will not be 100% mint. Check out our reproductions, they are VERY nice. This unit is sold individually. Ford part # C6VB-13B726-A.  *TRIVIA* Did you know that these units were originally used on the 1966 Lincoln? The...

Door lock latch lever, for driver or passenger side locks. Attach with an "E" clip on the rear side of the lock mechanism. Used "E" clip is included. We are going to say that these fit all Ford door locks 1965 through 1973 and beyond. *Note you will need to purchase or reuse your retainer clip for attaching the lock rod. Retainer clip not included, we have good used or reproduction clips, see related items.Ford number stamped C5AB-6221970-A or D2AB-6221970-AA  ...

Used license plate holder and fuel door for all 1967-68 Mercury Cougars. Comes as shown, hinges inspected, will include used or new license plate plastic inserts. See our list of related parts, will need rubber bumpers.Replaces Ford part number C7WB-13393.

Latch rod that links the door latch and the inside door handle, right or left side door. 1968 Mercury Cougar and Ford Mustang door latch rods are straight, and do not have a clip midway, compared to the 1967 version. Normally this rod was fabric covered. Used rod only, no retaining end clips. Replaces Ford part number C8ZZ-6521940-A. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click...

Reproduction trunk lock cylinder with keys for the 67 - 68 Mercury Cougar. Replaces Ford Part # C7SZ-6543505-A or C7SZ-6543507-B (Glove box/Trunk lock kit). Below are some basics about removing and replacing your lock cylinder and lock cover. When removing the cylinder from the lock housing this button must be depressed to allow the cylinder to slide out the front of the housing.  The only way to depress the button is to have the key in the cylinder and partially turned as if to...

Includes two door lock cylinders, two door cylinder gaskets, two keys and one ignition lock cylinder.  Made by the original OEM supplier.  That being said, they do not make them like they used to. Replaces Ford part # C7AZ-6222050-A or C9AZ-6222050-A.

*NOTE - These knobs are NOT in the original Ford packaging, they were bought in bulk from a supplier who did not provide packaging. This style of knob was used on almost all Ford products starting in 1968 and continuing on through the late 1970's. The latest renditions in reproduction form are actually pretty good but for the purist these make a nice touch. Paste the part number into the Ebay search box and sometimes you can get lucky and get a pair for under $30. Limited supply, original...

Exact replacement inside door handle nut, trunk lock nut, and hood scoop nut. Same finish as originals. 10 of these are used to mount the 68-71 hood scoop found on the 68 428 CJ, 69-70 Eliminator, 69-70 428 Ram Air equipped Cougars and 71 GT and 429CJ. Two of these per door are used on the 69-70 inside door release. Two of of these nuts used to attach 1967-68 Cougar trunk locks.

Correct style nut with captured washer for attaching hood scoops, 1969-70 Mercury Cougar inside door handles, and 1967-68 trunk lock. Correct nuts would have been black phosphate, these are shiny gold as shown.

Rubber pad for installing the trunk lock mechanism to deck lid.Check out our video below showing how to easily remove and reinstall your 67-68 trunk latch, lock, and cover plate, and some info on getting a new key made.

Used original driver side (left hand) key lock to latch door lock rod for the Mercury Cougar or Ford Mustang.Ford part # C7ZZ-6522135-A.

Used original passenger side (right hand) key lock to latch door lock rod for the Mercury Cougar or Ford Mustang.Ford part # C7ZZ-6522134-A.

This deck lock housing has been carefully stripped, polished and triple plated. You can send yours in in advance as an exchange or pay the core charge and return your old one later. Do know once a multi-faceted part like this has been stripped, polished and replated, some of the crisp, sharp detail will be muted and it will never again look just like factory. If you have extra cores we are buyers, especially if your lock assembly is complete. Be sure and watch our video below to see how to...

This part mates to and is held down by Golde #100 413 681. The Golde part number for the smaller, lower elbow guide is 100 413 664

This part mates to and is held down by Golde #100 413 682. The Golde part number for the smaller, lower elbow guide is 100 413 663

Folding lug wrench for all 1968 - 1973 Mercury Cougars. Standard folding wrench for 13/16" lug nuts. This version has the elongated hex socket portion. There is also a version that has a rounded upper section formed on the socket. This is also the scissors jack tool.There were minor variations over the years, but the handle you will receive will be one of the following:Ford part number: C8ZZ-17032-A (1968 - 1969)Ford part number: D0ZZ-17032-A (1970 - 1971) Ford part number: D4ZZ-17032-A...

Not 100% concours correct but close close in design to the 1968 - 1973 handle. Works well for 1967 as well. Replaces Ford Part Numbers: C5ZZ-17032-A, C5ZZ-17032-B ,C8ZZ-17032-A, D0ZZ-17032-A, D4ZZ-17032-A.Customer feedback from mercurycougar.net: Don and WCCC were always one of the service quality benchmarks for my business. Despite the many pressures faced by any small business owner, Don always treated me and my car as if we were his only customer. And, he NEVER let me down - parts...

Folding lug wrench for all 1968 - 1973 Mercury Cougars. Standard folding wrench for 13/16" lug nuts. This version has a rounded upper section of the hex lug socket. This is also the scissors jack tool.There were minor variations over the years, but the handle you will receive will be one of the following:Ford part number: C8ZZ-17032-A (1968 - 1969)Ford part number: D0ZZ-17032-A (1970 - 1971) Ford part number: D4ZZ-17032-A (Factory Service Replacement since 1974) If you'd like a particular...

Nice reproduction of the original Rotunda, over the counter dealer accessory. Stainless steel construction, weighs just under 8 pounds. The supplier unfortunately does not include the hardware and we have yet to source any. Actual dimensions are 20 1/2 inches wide, 48 1/2 inches long, and the back lip is 3 inches tall. Installation hole spacing is as follows. Rear spacing 47-11/16" on center, front spacing (nearest the rear window) is 47-9/16". The spacing on short sides are 18-3/4" on...

Map light bezel for overhead roof consoles on both 1967-68 Mercury Cougar XR7 and Ford Mustang. These are a great reproduction at a great price. These were always pitted and before the reproductions came out three years ago a very nice used pair sold for about $100. To date we have sold more than 300 pairs and have had great feedback! Sold in pairs. Bezels only. Sometimes called a 'door' Ford part number C7ZZ-13788-A. *Customer Comments* Hello. I just bought my first 1967 Cougar XR7 in about...