Body

New high quality fiberglass hood for the 1967 - 1968 Mercury Cougar. Inspired by the XR7-G hood scoop, our supplier molded these hoods with this taller functional hood scoop already attached (keep in mind that the original XR7-G and GT-E hood scoops are non-functional). The "nostrils" of the scoop are cut out, and there is a large opening beneath the scoop to provide extra airflow to the engine. This version of the G-Force hood has a steel under structure that is taken from an original...

Ultra rare item, subject to availability. Call about spent cylinders, we actively seek out those too. Our guess is that the contents of an NOS cylinder may be unstable for use.

Universal driver side (left hand) or passenger side (right hand) inner floor frame patch that you can trim to fit the area that needs to be repaired.

New inner floor frame support for the Mercury Cougar and Ford Mustang.

Full driver (left hand) side front frame rail that measures 52" long. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...

Full passenger (right hand) side front frame rail that measures 52" long. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...

Driver quality used left side or driver side folding door handle. This type of handle was used on the 1967 XR7 models and 1968 Cougars. This is also the deluxe handle found in Mustang and other Ford / Mercury cars. Some pitting, will have a good spring and rubber bumper. Sorry mounting screw not included.

Driver quality used right side or passenger side folding door handle. This type of handle was used on the 1967 XR7 models and 1968 Cougars. This is also the deluxe handle found in Mustang and other Ford / Mercury cars. Some pitting, will have a good spring and rubber bumper. Sorry mounting screw not included.

This is the factory Ford remote trunk latch as used on luxury cars such as Thunderbird or Lincoln. As you can see from the photo, they are made (and install) exactly like our Cougar trunk latches, but with the addition of a release tab. These can be installed to use either a cable, vacuum, or solenoid release.

Used grade "B" rear courtesy / opera light lens for the Mercury Cougar. Opera lights were came as standard equipment on all XR7 Cougars, but were installed on many decor and standard level Cougar interiors. These units will have a few "warts" which show up as pitting in the chrome and may also have some minor cracking in the lens. If you just need a lens for your driver quality car, these are a great option. But if you compare this grade "B" lens to our reproductions, it will look like...

This is for the person who is missing it all. Includes all you need as seen in the picture and includes the reproduction chrome cover on a good used housing. Let us know in the comments whether you prefer a Standard or XR7 decal installed on the flip up door. Check out our video below showing how to easily remove and re-install your 67-68 trunk latch, lock, and cover plate and some info on getting a new key made. This icon means that we're looking to buy this part!WCCC is a buyer of used and...

Good used cylinder as taken from a 1967 - 1968 trunk lock housing. Will have minor damage but cosmetic only, 100% functional. Ford Part # C7SZ-6543505-A or C7SZ-6543507-B (Glove box/Trunk lock kit) Below are some basics about removing and replacing your lock cylinder and lock cover. When removing the cylinder from the lock housing this button must be depressed to allow the cylinder to slide out the front of the housing.  The only way to depress the button is to have the key in the...

A perfectly working, matched set of trunk and glove box locks with key is getting rather hard to come by these days. These two matching locks are guaranteed to work perfectly. Includes 1968 style glove box lock, 1967-68 Cougar trunk lock cylinder with one "Ford" cut key to the coded to the number imprinted on the glove box lock. This is a matching set with new key. 1967 glove box locks has square edges on the front of the lock. Starting in 1968 the lock had a rounded edge on the front. We also...

This matched set is actually for a 1968 model Cougar but works just as well on a 67. The only difference being 1967 had squared off edges on the glove box button and 1968 had rounded edges which are safer in a collision.Ford Part # C7SZ-6543505-A/C6OZ-6206281-C or C7SZ-6543507-B (Glove box/Trunk lock kit)

Refurbished pair of door lock cylinders and ignition cylinder for all double cut key Fords 1967-69. These are coded to the original key code, which was stamped onto one of the door lock cylinders. Includes two door lock cylinders, two Ford keys, and one ignition lock cylinder. Assembled from the best used locks. Replaces Ford part # C7AZ-6222050-A or C9AZ-6222050-A.

This is a good used, grade A deck lock housing with nothing included except the studs. There will be no major blemishes or pitting and the cover stop in the bottom corner is intact. This is an impossible part to have restored and look OEM so finding a really good used one is important for a high quality restoration.

This is a decent used, grade B deck lock housing with nothing included except the studs. There will be a couple of blemishes that may include minor pitting but the cover stop in the bottom corner is intact. Perfect for a driver as very little of the chrome shows when this is installed, our reproduction cover will cover almost all of this part in the down position. Check out our video below showing how to easily remove and reinstall your 67-68 trunk latch, lock, and cover plate, and some info...

Nice used original Rotunda, over the counter dealer accessory. Stainless steel construction, weighs just under 8 pounds with hardware. Actual dimensions are 20 1/2 inches wide, 48 1/2 inches long, and the back lip is 3 inches tall. Installation hole spacing is as follows. Rear spacing 47-11/16" on center, front spacing (nearest the rear window) is 47-9/16". The spacing on short sides are 18-3/4" on center. This rack was utilized for may years on many cars. The same company made them for...

Straight Monte Carlo Bar in stainless steel for Mercury Cougar and Ford Mustang. The Monte Carlo Bar was originally developed by Carroll Shelby to help maintain proper wheel alignment under hard cornering. Not only will this item help stiffen the notoriously flexy front end, it will also help reduce the chances that your shock towers will develop stress cracks over time. Replaces Ford part # C7ZZ-16A052-ARS.

Reproduction support brace to be used with 1967-70 Mercury Cougar and Ford Mustang export braces. Can be used with OEM, NOS or reproduction export braces. Contoured to match the curvature of the cowl.*Note - Will not fit early Shelby Mustangs.This part never came from the factory, but the idea was taken from the fact that Shelby cars had plates like these, though these are not interchangeable with Shelby export braces or export brace plates because of hole placement. The original Shelby part...

Spare tire, with styled steel wheel hold down disc. Fits all 1968-70 Mercury Cougar and Ford Mustang.  About 3 inches in diameter, this is the specified trunk hold down plate for the use with the factory mag wheels. We won't always have the used in stock, but the reproduction version is very good.Replaces Ford part number C8MY-1424-A.

These spacers are required to properly mount the trunk lock housing to the trunk. Two required per car, sold individually. Ford part number C7WY-6543565-A. Check out our video below showing how to easily remove and reinstall your 67-68 trunk latch, lock, and cover plate, and some info on getting a new key made. ...

Full passenger (right hand) side front frame rail that measures 52" long and the outer rail has weld nuts installed for proper installation. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...

Reproduction cover board for the rear package tray found on the 1968 Mercury Cougar behind the rear seat, visible through the rear window. The 1968 tray is not as deep as the 67 as it installs under the tops of the rear side panels. In 1967 they installed over the rear vinyl covered panels. The difference between the WCCC panels and the others on the market is that we run them through a drum sander so as to give the textured side a more muted look and feel than unsanded masonite board. The...

Good used piece of insulation / sound deadener that is distinctly different from 1967. This pad weighs more than four times what the reproduction does and will much more effectively insulate the passenger compartment of your Cougar from sound, heat and cold. Notice it comes with the factory perforations for speakers and rear window defog unit.

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. This SEM plastic and leather paint prep is for cleaning surfaces before applying the SEM flexible vinyl paint. Removes mold, grease, oil and other contaminates from leather, carpet, velour and vinyl.

New pair of white and yellow paint sticks for the Mercury or Ford. These units were used by FORD at the assembly plants to mark fender aprons, radiator support, transmission, rear end housing, sheet metal, glass and variety of other parts. It's often little details like this that separate first and second place at the show.

Will require trimming to fit your year application. Note that 1967 has the three raised enforcements facing the inside of the trunk and 1969-73 the raised portions face outward. Thus you will want this panel for the passengers side of those series. ...

Will require trimming to fit your year application. Note that 1967 has the three raised enforcements facing the inside of the trunk and 1969-73 the raised portions face outward, Thus you will want this panel for the drivers side of those series. 

Here is our used lower rear window channel which we will cut to suit your needs. Quite often vinyl tops will cause rust in this area and this part is cut from a rust free Western parts car. If you need the package tray attached there is no extra charge, but shipping costs will increase. We usually cut generous into the quarters and several inches up the sides of the rear glass. If you only need one side contact us as we can help.   ...

Crating Fee Applies To This Item. You will be contacted once your order is reviewed to discuss the crating fee. Crating fees generally run between $175 - $250 (this does not include truck freight charges). If an item has a crating fee, this usually indicates that it must ship via Truck Freight and can only be shipped to US addresses and select Canadian addresses. Since we never have all years and sides in stock at any given time in Grade "A" form and since almost every panel has "some" minor...

Crating Fee Applies To This Item. You will be contacted once your order is reviewed to discuss the crating fee. Crating fees generally run between $175 - $250 (this does not include truck freight charges). If an item has a crating fee, this usually indicates that it must ship via Truck Freight and can only be shipped to US addresses and select Canadian addresses. Since we never have all years and sides in stock at any given time in Grade "A" form and since almost every panel has "some" minor...

The reproductions are good quality but nothing fits like OEM parts from original tooling! Ford part number C7WY-6527841-AKeep in mind that this item is over-sized and will cost about $275 to drop ship a single panel via truck freight direct from the supplier. We will have to manually calculate shipping and crating, you will not get an accurate shipping cost from the website. For details feel free to call us at 503-463-1130.

The reproductions are good quality but nothing fits like OEM parts from original tooling! Ford part number C7WY-6527840-A Keep in mind that this item is over-sized and will cost about $275 to drop ship a single panel via truck freight direct from the supplier. We will have to manually calculate shipping and crating, you will not get an accurate shipping cost from the website. For details feel free to call us at 503-463-1130. ...

This reproduction patch is for the area after the door and before the rear wheel on the driver (left hand) side.Keep in mind that if you were to purchase an entire reproduction quarter skin,the fittament and quality will be much better than these individual patches. ...

This reproduction patch panel is for the area after the door and before the rear wheel on the passenger (right hand) side.Keep in mind that if you were to purchase an entire reproduction quarter skin,the fittament and quality will be much better than these individual patches. ...

This quarter panel patch is for the driver (left hand) side behind the rear wheel.Keep in mind that if you were to purchase an entire reproduction quarter skin,the fittament and quality will be much better than these individual patches. ...

This quarter panel patch is for the passenger (right hand) side behind the rear wheel.Keep in mind that if you were to purchase an entire reproduction quarter skin,the fittament and quality will be much better than these individual patches. ...

For deck / trunk lids it is all about rust under the inner rear lip... We still check it over good for excessive filler, correct contour on all the lines and hidden rust under the weather strip. We ship deck / trunk lids with several layers of thick cardboard and insure them for the full amount. Keep in mind shipping is free if you order at the same time as a hood, door or quarter panel. For those wanting a cleaner look on their 1967-68 Cougar a 69-70 deck / trunk lid will bolt right on with...

[No Description Provided]

[No Description Provided]

[No Description Provided]

[No Description Provided]

[No Description Provided]

[No Description Provided]