All Products

C6OE-9425-B Cast iron intake manifold used on all 1967 A code 289-4V engines in a Mercury Cougar or Ford Mustang. Stock 4 barrel intake manifold. Take off manifold with correct casting number of C6OE-9425-B. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C4OZ-9424-G. *Installation Tip - A 1 inch aluminum spacer plate with PCV provision is needed for proper air cleaner clearance.

C8ZE-9425-A Cast iron intake manifold used on all 1968 J code 302-4V engines in a Mercury Cougar or Ford Mustang. Stock 4 barrel intake manifold. Take off manifold with correct casting number of C8ZE-9425-A. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C4OZ-9424-H. *Installation Tip - A 1 inch 4 barrel aluminum spacer plate with PCV provision is needed for proper air cleaner clearance.

D0AE-9425-E, -H, or -L Cast iron intake manifold used on all 1970-71 M code 351-4V engines in a Mercury Cougar or Ford Mustang. Stock 4 barrel intake manifold. Take off manifold with correct casting number of D0AE-9425-E, -H, or -L . Intake shipped bare, less choke stove, carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number D0AZ-9424-C. *Note - 351 Cleveland engines only.

Cast iron intake manifold used on all 1973 Q code 351-4V or 351CJ engines in a Mercury Cougar or Ford Mustang. Stock 4 barrel intake manifold. Take off manifold with correct casting number of D3ZE-9425-AA . Intake shipped bare, less choke stove, carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number D3ZZ-9424-A. *Note - 351 Cleveland engines only. *Installation Tip - A spacer plate with EGR provision is needed for proper installation. ...

C9OE-9425-A or -F Cast iron intake manifold used on all 1969-70 H code 351-2V engines in a Mercury Cougar or Ford Mustang. Stock 2 barrel intake manifold. Take off manifold with correct casting number of C9OE-9425-A or -F. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C9OZ-9424-A. *Installation Tip - A 1 inch aluminum spacer plate with PCV provision is needed for proper air cleaner clearance. *Note - 351...

C3AE-9425-B Cast iron intake manifold used on all 1963 390-4V engines in a Mercury or Ford. Stock 4 barrel intake manifold. Take off manifold with correct casting number of C3AE-9425-B. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Fits FE engines, this could have come from a Galaxie or Thunderbird or full sized Mercury. Probably also 352 engines. Current date available: 2M29. December 29, 1962. *Trivia - One of the heaviest car...

C8AE-9425-F Cast iron intake manifold used on all 1968 S code 390-4V engines in a Mercury Cougar or Ford Mustang. Stock 4 barrel intake manifold. Take off manifold with casting number of C8AE-9425-F. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C8AZ-9424-C. There are other versions of this "S" intake manifold with a suffix "A" letter.  Current dates available: 8A23. *Trivia - One of the heaviest car...

Reproduction rear courtesy / opera light lenses for the Mercury Cougar. The rear courtesy / opera lights were standard equipment on all XR7 Cougars, but were a popular option many other standard and decor level interior Cougars. If your car did not originally come equipped with them, it is actually quite easy to install them, but you will need to purchase our used housing /socket assemblies. These are fantastic quality and a perfect fit. Sold as a pair only. Ford part # C6VB-13B726-A. *TRIVIA*...

Direct plug in solid state replacement, no modifications needed. We highly suggest considering not purchasing this unit and invest in the all inclusive unit. All of the original sequential components in the trunk of your Cougar are mechanical and will in time fail. It is much more cost efficient to buy the all inclusive unit than to purchase them one by one as they fail. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the...

No modifications needed, just open the trunk and plug the unit into your original wiring! We highly suggest considering not purchasing this unit and invest in the all inclusive unit. All of the original sequential components in the trunk of your Cougar are mechanical and will in time fail. It is much more cost efficient to buy the all inclusive unit than to purchase them one by one as they fail. This reproduction is an exact replacement for this original unit. This updated relay will...

Kick panels for the 1967 and 1968 Mercury Cougar that include 6 1/2" coaxial (2 way) 100 watt speakers. Available in black, but can be sprayed to match your interior. Sold as a pair. For some discussion on kick panel speaker options, check out this thread.

Great way to update your sound system without cutting door panels or other original parts. Great fit and finish, easy installation. Pioneer speakers are 4ohms, 6 1/2" coaxial (2 way) 160 watts per speaker, for a total of 320 watts max output! Only available in black, but can be painted to match your interior with flexible paint. For more discussion on kick panel speaker options, check out this thread.

Kick panels for the 1967 and 1968 Mercury Cougar that are formed to accommodate speakers. Speakers are not included. These are designed for those who would like to choose their own speakers. Available in black, but can be sprayed to match your interior. Sold as a pair. These now come pre-cut for a 5 1/4 inch speaker. For more discussion on kick panel speaker options, check out this thread.

Sold as a pair. The overlay bonded to the plastic really gives a feel and look of quality to these kick panels. For more discussion on kick panel speaker options, check out this thread.*NOTE* These units may require some slight modification to fit perfectly in your unique Cat or Pony.

Sold as a pair. The overlay bonded to the plastic really gives a feel and look of quality to these kick panels. For more discussion on kick panel speaker options, check out this thread.

Knee pad as found on select 1968 Mercury Cougars. This grade A version will not be separating from the metal strip. Not a common option, your Cougar would have a line of mounting holes across the lower dash and above the glove box if your Cougar originally came with a knee pad. We don't always have these in stock in this condition. Call for desired color, but plan on spraying with a quality vinyl dye for best results. Black is our most popular requested color, and we will probably always be...

The early Cougars had a lower profile head on the outer knob. It is assumed they beefed up the design in early in the year because the knobs were easily broken. These delicate plastic knobs are very hard to find in this condition. Only the utmost purist would care to obtain a trivial detail part such as these to make their car correct. These deeper knobs were only used in cars equipped with a factory center console. The Mustangs did not have a padded console in 1967 so this set is for 1967...

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. Used lower knuckle for the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. This knuckle is unique to 1967 because the center hole is round. The 1968-69 features an elongated center hole.  There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* We'll give you UP TO $100 cash back for your...

Used upper knuckle for the tilt / tilt away steering column equipped Mercury Cougar or Ford Mustang. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Reproduction driver side (left hand) convertible top latch assembly for the Mercury Cougar or Ford Mustang.  

Used convertible top latch handle for the driver side (left hand) for the Mercury Cougar or Ford Mustang.Ford part # D1ZZ-7650509-A , casting # D1ZB-7650509-A

Used convertible top latch handle for the passenger side (right hand) of the Mercury Cougar or Ford Mustang.Ford part # D1ZZ-7650508-A , casting # D1ZB-7650534-AA

Keep in mind we also have these in used form. for a little more (or less) money depending on condition. This part fits all Mustangs and Cougars 1965 - 1970. Replaces Ford Part #: C5ZZ-7650509-K. Casted Pot Metal with Engineering # C4ZB-7650535-C

Used driver side convertible latch handle. Fits 1969-70 Mercury Cougar and 1965-70 Ford Mustang. Cast aluminum, good condition, may have a nick or scratch, fully functional and does have the bushing for the attaching bolt. Will need a new hook if desired.  Ford part number C4ZB-7650535-C.

Keep in mind we also have these in used form. for a little more (or less) money depending on condition. This part fits all Mustangs and Cougars 1965 - 1970. Replaces Ford Part #: C5ZZ-7650508-KCast Pot Metal with Engineering # C4ZB-7650534-C

Used passenger side convertible latch handle. Fits 1969-70 Mercury Cougar and 1965-70 Ford Mustang. Cast aluminum, good condition, may have a nick or scratch, fully functional and does have the bushing for the attaching bolt. Will need a new hook if desired. Ford part number C4ZB-7650534-C.

Used stamped steel lateral compressor support bracket for Cougars and Mustangs built after 3/1/1968 with the 289 or 302 engine. Very close in design to the 1969 351 Windsor, but smaller overall.Ford part # C8AZ-2888-B.

Used stamped steel lateral support bracket for all 1970 Mercury Cougars and Ford Mustangs with the 351 Windsor or Cleveland engine. Ford part # D0OZ-2888-A*NOTE* - Excludes all 1969 351 Windsor engines.

Stamped steel A/C lateral support brace for all Mercury Cougars and Ford Mustangs with the 351-2V or 351-4V Windsor engines. Ford part # C9OZ-2888-B. *NOTE* - Excludes all 351 Cleveland engines and 1970-71 351 Windsor engines.

Used steel lateral support bracket for 1967 Cougars and Mustangs with the S code 390 engine. Similar to the more commonly found 68-70 bracket but different in multiple ways, most noticeably is the lip on the 1967 "C" shaped area points outward (towards the radiator). Below are some pictures of a 390 with AC and smog. This motor was pulled from a 1967 Thunderbird so there are a few minor differences when compared to a 1967 Mustang or Cougar but the mounting of brackets and belt alignment are...

Used steel lateral support brace for Cougars and Mustangs with the 390-2V, 390-4V, or 428CJ FE engines. Identical to the 1970 FE lateral bracket except 1970 versions have square nuts on the reverse.Ford part # C8AZ-2888-A

Used steel lateral support brace for Cougars and Mustangs with 428CJ FE engines. Identical to the 1968-69 FE lateral bracket except 1970 versions have square nuts on reverse. Also the same bracket for Ford passenger car 390 up until 1971.Ford part # D0AZ-2888-B

Reproduction Legendary Series GT5 Alloy Wheel. This updated design was created using state of the art casting technology for superior strength and precision. These wheels take a specific shouldered 3/4" lug nut, find them here. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat decals (click here). Just add it to your cart if you'd like these decals. If you want to upgrade to a premium...

Reproduction clear coat natural finish aluminum alloy rim for the 1967 - 1973 Cougar or Mustang. Designed to look like the optional 10 spoke alloy wheel that was available on 67 - 68 Shelby GT350's ang GT 500's. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat decals (click here). Just add it to your cart if you'd like these decals. If you want to upgrade to a premium quality center...

Reproduction Legendary GT9 series aluminum wheel in the gloss black finish. It was inspired by the factory Shelby rim used on the 1969-70 GT350 and GT500’s. It was and still is a great looking combination of the original Torque Thrust and the iconic Magnum 500. All versions feature a gloss clear coat for protection. 4.25" Back spacing5 x 4.5" Bolt pattern These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black...

Reproduction Legendary GT9 series aluminum wheel in the charcoal finish. It was inspired by the factory Shelby rim used on the 1969-70 GT350 and GT500’s. It was and still is a great looking combination of the original Torque Thrust and the iconic Magnum 500. All versions feature a gloss clear coat for protection. 4.25" Back spacing5 x 4.5" Bolt pattern These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and...

Reproduction Legendary GT9 series aluminum wheel in the natural finish. It was inspired by the factory Shelby rim used on the 1969-70 GT350 and GT500’s. It was and still is a great looking combination of the original Torque Thrust and the iconic Magnum 500. All versions feature a gloss clear coat for protection. 4.25" Back spacing5 x 4.5" Bolt pattern These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and...

Reproduction Legendary GT9 series aluminum wheel in the natural finish. It was inspired by the factory Shelby rim used on the 1969-70 GT350 and GT500’s. It was and still is a great looking combination of the original Torque Thrust and the iconic Magnum 500. All versions feature a gloss clear coat for protection. 4.25" Back spacing5 x 4.5" Bolt pattern These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and...

Reproduction 15 x 7 charcoal colored aluminum alloy rim for the 1967 - 1973 Cougar or Mustang. Designed to be a cross between the vintage A/C Cobra and the Eleanor rim. 4.25" back spacing. Bolt pattern: 5 x 4.5 NOTE* These Legendary wheels require Legendary lug nuts. NOTE: Spinner cap is not included, you can find it here. You can also purchase the lug nut cover with low profile lugs. Check out our video on Legendary Wheels below: ...

Reproduction 15 x 7 gold haze colored aluminum alloy rim for the 1967 - 1973 Cougar or Mustang. Designed to be a cross between the vintage A/C Cobra and the Eleanor rim. 4.25" back spacing. Bolt pattern: 5 x 4.5 NOTE* These Legendary wheels require Legendary lug nuts. NOTE: Spinner cap is not included, you can find it here. You can also purchase the lug nut cover with low profile lugs. Check out our video on Legendary Wheels below: ...

Reproduction 15x7" Eliminator wheel with a black center and chrome rim for the Mercury Cougar or Ford Mustang / Torino. The only version of this wheel Mercury ever used on a factory order for a Mercury Cougar was a painted 14x6 with a trim ring used on the 1969 Eliminator. This black 15x7 is a really great custom made wheel that adds flash without deviating too far from the original look. As always, the cap is sold separate. Click here for the hubcap we recommend for this wheel. If you need a...

Reproduction 15x7" Eliminator wheel with a charcoal center and chrome rim for the Mercury Cougar or Ford Mustang / Torino. The only version of this wheel Mercury ever used on a factory order for a Mercury Cougar was a painted 14x6 with a trim ring used on the 1969 Eliminator. This charcoal 15x7 is a really great custom made wheel that adds flash without deviating too far from the original look. As always, the cap is sold separate. Click here for the hubcap we recommend for this wheel. If you...

Reproduction 15x7" Eliminator wheel with a silver center and chrome rim for the Mercury Cougar or Ford Mustang / Torino. The only version of this wheel Mercury ever used on a factory order for a Mercury Cougar was a painted 14x6 with a trim ring used on the 1969 Eliminator. This silver 15x7 is a really great custom made wheel that adds flash without deviating too far from the original look. As always, the cap is sold separate. Click here for the hubcap we recommend for this wheel. If you need...

New Legendary Series 15x7" Glossy Finish Magnum 500 wheel for your Mercury Cougar or Ford Mustang. While they look almost identical to the original chromed steel version, these are actually a lighter, better-balanced aluminum alloy with a protective coating. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat decals (click here). Just add it to your cart if you'd like these decals. If...

New Legendary Series 15x7" Charcoal Finish Magnum 500 wheel for your Mercury Cougar or Ford Mustang. While they look almost identical to the original chromed steel version, these are actually a lighter, better-balanced aluminum alloy with a protective coating. We also have center caps for these wheels that feature the Mercury man or the walking cat logo. Center caps and lug nuts sold separately. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we...

New Legendary Series 15x7" Satin Finish Magnum 500 wheel for your Mercury Cougar or Ford Mustang. While they look almost identical to the original chromed steel version, these are actually a lighter, better-balanced aluminum alloy with a protective coating. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat decals (click here). Just add it to your cart if you'd like these decals. If...

New Legendary Series 15x7" Stealth Black Finish Magnum 500 wheel for your Mercury Cougar or Ford Mustang. While they look almost identical to the original chromed steel version, these are actually a lighter, better-balanced aluminum alloy with a protective coating. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat decals (click here). Just add it to your cart if you'd like these...

New Legendary Series 15x8" Glossy Finish Magnum 500 wheel for your Mercury Cougar or Ford Mustang. While they look almost identical to the original chromed steel version, these are actually a lighter, better-balanced aluminum alloy with a protective coating. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat decals (click here). Just add it to your cart if you'd like these decals. If...