All Products

Good used driver side (left hand) quarter window guide for the Mercury Cougar or Ford Mustang. Grade B will have some rust or erosion from moisture, missing zinc plating. This unit will have all three window stops and both window guides still attached. Riveted window stops have part number of C4ZB-6529838-A. Ford part # C7ZZ-6529753-A. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our...

Good used passenger side (right hand) quarter window guide for the Mercury Cougar or Ford Mustang. Grade B will have some rust or erosion from moisture, missing zinc plating. This unit will have all three window stops and both window guides still attached. Riveted window stops have part number of C4ZB-6529838-A. Ford part # C7ZZ-6529752-A. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our...

Chromed quarter window moulding or 'hockey stick' mounting bracket for the driver side only of 1969-70 Mercury Cougars. Coupe only, will not fit convertibles. Also attaches the outer window fuzzy or belt line kit component. Aluminum construction, these can be bonded to our reproduction quarter trims. Item cleaned for photos, item shipped will likely have the remnants of the window seal and road tested dirt.Replaces Ford part number C9WY-6529035-A

Chromed quarter window moulding or 'hockey stick' mounting bracket for the passenger side only of 1969-70 Mercury Cougars. Coupe only, will not fit convertibles. Also attaches the outer window fuzzy or belt line kit component. Aluminum construction, these can be bonded to our reproduction quarter trims. Item cleaned for photos, item shipped will likely have the remnants of the window seal and road tested dirt.Replaces Ford part number C9WY-6529034-A

New 13 Pound Generic Radiator Cap with Safety Release for the 1967 - 1973 Mercury Cougar / Ford Mustang

This is a radio nut removal tool used to remove the radio shaft nuts. No more trying to remove those little units with the wrong tools and potentially damaging your bezel or dash. These are made from HRS steel and are milled to fit the shaft nut perfectly.

Correct plug for your 1967 - 1973 Mercury Cougar or Ford Mustang. Often these have been cut from the main loom to install an after market radio.

Reproduction radio plug and pigtail for your 1967 - 1971 Mercury Cougar or Ford Mustangs.

Reproduction black extruded plastic shield, or rain gutter for the voltage regulator on any 1969-70 Mercury Cougar or Ford Mustang. Replaces Ford part number C9ZZ-10A506-A.

Used black extruded plastic shield, or rain gutter for the voltage regulator on any 1969-70 Mercury Cougar or Ford Mustang. Ford part number C9ZZ-10A506-A.

Reproduction driver side (left hand) rear apron extension for Mercury Cougar and Ford Mustang.

Reproduction passenger side (right hand) rear apron extension for Mercury Cougar and Ford Mustang.

Reproduction rear boot for your 67 - 69 Cougar or Mustang Midland power brake booster.

Used trunk or luggage compartment latch, fits all 1967-73 Mercury Cougar and many other Ford and Mercury cars. Comes with 3 bolts for mounting.Replaces Ford part number C5AZ-6243200-A.

Fits Standard and XR7 Sold as a Kit as Pictured.

Set of 1-1/4" leaf spring rubber bushings for the rear eye of the spring. Sold in packages of 8, 4 per side. Correct shackle bushings for all 1971 through 1972 Cougars manufactured between 10/70 and 9/71. Replaces Ford Part #: C6ZZ-5781-B & C6DZ-5781-A.

Good used L bracket that is not heavily rusted or bent. Passenger side is marked from the factory with an "R" and driver side is marked with an "L". The portion with the lip mounts vertically and the purpose of the lip is to align the splash shield into the proper location.

Reproduction pair of lower fender braces. The portion with the lip mounts vertically and the purpose of the lip is to align the splash shield into the proper location.

Good used L bracket that is not heavily rusted or bent. Passenger side is marked from the factory with an "R" and driver side is marked with an "L". The portion with the lip mounts vertically and the purpose of the lip is to align the splash shield into the proper location.

The metal portion on the Mustang shield is identical to the 1967-68 Cougar rear shields, but the rubber is different between the Cougar and Mustang. We are in the process of trying to get the correct rubber for the Cougar. Replaces Ford Part # C7ZZ-16103-B.

The metal portion on the Mustang shield is identical to the 1967-68 Cougar rear shields but the rubber is different between the Cougar and Mustang. We are in the process of trying to get the correct rubber for the Cougar. Replaces Ford Part # C7ZZ-16102-B.

Kit for rebuilding your drum brake distribution block on your Mercury Cougar or Ford Mustang. Special square O-rings are made from EPDM (Ethylene Propylene 70 Durometer) which is specifically designed to withstand chemical degradation caused by prolonged exposure to brake fluid.*Customer Feekback*"You guys are awesome, I couldn't find a rebuild kit for my Galaxie's brake distribution block anywhere else! Thank you!" Henry M.Here’s a video to help you rebuild the distribution block so that you...

Reproduction C5AZ-7630702-A Ashtray receptacle for 1969-70 Mercury Cougar and Ford Mustang. Only the rear door panel ashtrays in the back seat area. Slightly deeper than the OEM ash trays, plenty of room for installation. Receptacle only, sliding covered retainer sold separately, find it here. Also fits 1965-68 Ford and Mercury full sized convertibles. 

This receptacle was used on the 1967-68 rear of all consoles except the 1967 standard. It was also used in the rear interior panels of the 1971 - 1973 Cougar for both convertible and coupe. Not correct for 1969 - 1970 convertible rear side panels.Ford part number C5AZ-6230702-A.

These Spark Plug Wire Separators are made of high-quality ABS plastic. Constructed to hold both standard 7mm and 8mm high-performance spark plug wires. Fits directly on valve cover clip. Available in blue, red and OE black.

Used flexplate reinforcing ring, Ford called it a fly wheel reinforcing plate. Fits all Ford small block engines including 260, 289, 302, 351W and 351C. Strengthens the area where the automatic transmission flex plate mounts to the crankshaft. This is not just a ring with 6 holes in it, it is indexed specifically for the flex plate and only goes on one specific way. It has to be indexed because of the weight on the flex plate. Just under 4 inches in diameter. Special bolts not included, but...

Reproduction flexplate reinforcing ring. Strengthens the area where the automatic transmission flexplate mounts to the crankshaft. 5.12" outside diameter3.34" inside diameter .060 inches thickFits: 352 390 427 428 429 460 with C6 and FMX transmissions.Replaces Ford part # B9AZ-6A6366-B

Used sequential unit (found in trunk) relay for all 1970-73 Mercury Cougar, 4 total per car. Additionally this relay was used as a horn relay for 1965 Ford Mustang with generators; 1966 Lincoln Continental relay for moveable steering columns; 1969 and later Ford and Mercury full sized with speed control relay and power back window relay (on station wagons). Ford Engineering # C4AZ-13853-A. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most...

This is a good quality non-concours starter solenoid. Inexpensive replacement if you are not worried about being 100% correct. Disappointing quality, often will fail in less than a year, we recommend buying original FoMoCo. Replaces Ford part # B6AZ-11450-A, C7AZ-11450-A & D2AF-11450-A.

Used release lever for the tilt / tilt away steering column equipped Mercury Cougar or Ford Mustang. This unit is sometimes also called a bale. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Tilt release lever or bale. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

New to the market grille fix for 1967 - 1968 Mercury Cougars / Patent Pending. These simple little grille repair clips have been needed since these cars were new! Over the years we have seen a multitude of home remedies to fix this common problem but none were this clean looking, easy to install and failure proof. Soon we will be listing all the different FoMoCo applications these clips will work on. These clips are sold as a set of four. NOTE: We've found that removing the legs from one side...

These simple little grille repair clips have been needed since these cars were new! Over the years I have seen many home remedies to fix this common problem but none were this clean looking, easy to install and failure proof. Soon we will list the all the different FoMoCo applications from the era that these clips apply to. These clips are sold as a set of four. Click on images to enlarge. ...

Every now and again, the studs that hold the rear moulding begin to rust and break away from the body of the car. No need to install your rear window trim with missing studs and clips......just screw one of these little guys into place and Viola! Problem solved.  Sold in a box of 100, we also list them individually. #4-24 X 3/8" 7/32" Head Diameter Phillips Flat Head If you were missing every stud on your windows, you would need: 67 - 68 = 22 front, 20 rear 69 - 70 = 13 front, 24 rear 71...

This direct replacement resistor is used between the heater switch and the blower motor. These often fail and prevent the blower motor from turning on. Replaces Ford part # C2OA-18591-A. 1962 - 1967 Ford Fairlane1962 - 1964 Ford Galaxie1964 - 1966 Ford Thunderbird 1967 Ford Mustang 1968 Ford Mustang ...

New heater blower motor resistor for Mercury Cougars and Ford Mustangs equipped with factory A/C. This unit attaches to the heater blower fiberglass housing. Replaces part # C7ZZ-18591-B.

Used cigar or cigarette lighter threaded retainer with ground lug. Fits any 1969 Mercury Cougar and Ford Mustang with factory installed console. The ground lug is needed for the heating element in the socket. The consoles are made of plastic and use the common socket designed for steel dashes. This retainer is part of C9MB-15055-A socket and retainer assembly. 

Used steel rear retaining bracket for the headlight switch on any 1971-73 Mercury Cougar or Ford Mustang. These are bare steel and will have a bit of flash rust as shown, nothing serious. Replaces Ford part number D1ZB-13B107-AC.

Used rear retainer for the ignition lock cylinder on any 1967-68 Mercury Cougar or Ford Mustang. Good value, used as they come out of the cars, will have some flash rust since they were never plated or painted, usually it will not come with the small screw. This unit locates and maintains the angle to the dash from behind. Attaches with one small screw, and the bezel and retainer nut secures the whole works to the dash from the front. 1967-68 Mercury Cougar and Ford Mustang. 

Cougar actually used a larger ribbed plate on manual transmission cars without a console but this Mustang part is an inexpensive alternative. The rubber shift boot screws to the transmission tunnel, carpet then goes over it and lastly this retainer slips over the boot and hides the cut edges of your carpet. Shift boot sold separately.Replaces Ford Part #: C5ZZ-7262-C.

Used wiring harness retainer bracket for mounting the steering column bracket, on any 1973 Mercury Cougar or Ford Mustang. Retainer only, many of these are missing. Probably not missed, limited to stock on hand. Basic Ford part number 14A163.

Used steel rear retaining bracket for the windshield wiper switch and cigar lighter on any 1971-73 Mercury Cougar or Ford Mustang. These are bare steel and will have a bit of flash rust as shown, nothing serious. Replaces Ford part number D1ZB-17C584-AC.

Reproduction lower ball joint retainer and gasket. Works on 67 - 73 Cougars and Mustangs.

Reproduction retainer clip for the back up light switch wiring on the 67 - 69 Cougar or Mustang equipped with a 3 or 4 speed transmission.Replaces Ford part number C7ZZ-14163

Good used 1970 factory installed clip for attaching the high pressure line to the power steering reservoir low pressure tube. Kind of kept the line oriented during installation of the high pressure fitting. For all 1970 Mercury Cougar and Ford Mustang with 351W, 351C or Boss 302 engines. This is more for reference, this clip is much smaller than the one found on 1971-73 Mercury Cougar and Ford Mustangs with power steering. Basic Ford part number in 1970 chassis manual is 3E506. No...

Functional used nut with heavy scratches. The originals have deeper grooves and have a better luster on the chrome than the reproductions. This is a one year only design. Don't forget to check out our special tool used to remove and install this nut.

Replaces the original Ford part that features a # C7SB-17B732-A casting number. Basically correct for 1967 but works just as well on 1968 mirrors. These nuts are are not 100% correct for a 67 or 68, kind of a mixture of both.Very nice chrome quality at a reasonable price. NOTE: Our mirror nut removal tool works & fits perfectly with the original mirror nuts. However, you will find the tool will NOT fit this reproduction nut properly, it will require that it be filed a...

Reproduction pump end return hose for the 67 - 70 Cougar or Mustang. Cut to 2' length.