All Products

This gasket seals the fresh air tube in the cowl to the heater box inlet on 1967 through 1970 Cougars.

Locking nut for attaching the door window regulator to the window channel bracket on any 1969-70 Mercury Cougar or Ford Mustang. While we do not sell the T-bolts for attaching to the regulator (T-bolt Ford Part # C8SZ-6523274-A), we do have a retainer to keep it in the front channel bracket. Find it here. This is not an exact replica of the t-bolt lock nut, but is a functional replacement part. Replaced Ford part #: 34975-S ...

Flange nut for attaching any 1970 Mercury Cougar or Ford Mustang amber or red side marker lights. 8-32 threaded nut with wide flange. Two per lens, sold individually. 

[No Description Provided]

Replaces Ford Part # 381985-S Sold individually

Bumper bolt nuts sold individually. Also available in our bumper bolt kit.Please know that chrome cracking from the installation of bumper bolts on our rechromed bumpers is not covered under warranty. We have observed that some reproduction wavy washers are of a thicker material than original and require more torque to flatten out properly for a good fit. We suggest that no matter what thickness your repro wavy washer is that you flatten them out in a vise prior to installation so as not to...

Self threading speed nut for attaching "COUGAR' scrip emblems to the rear quarter panel of any 68 - 70 Mercury Cougar. Sold individually, 4 needed per emblem. Whereas these work fine, the originals were an acorn style nut and look very different.

Special nut with large diameter spinning washer for the set screw for the door glass adjustment. Sets and holds your door glass angle to allow a proper seal. Three set screws work in conjunction for each door glass and vent window combination. See your shop manual for actual procedure.See also 378696-S for the vent window and front door channel set screws.Ford part number 33797-S.

383278-S 1/4-20 Nut with spinning or captured washer, sometimes called a swivel nut, for attaching various door window components for 1970-1973 Cougar and Mustang bolt-in door glass. This nut was used to fasten the guides into the 1970 bolt in glass. Additionally this nut was used for attaching the window channel bracket to door and quarter glass on the 1971-73 Cougar and Mustangs. This is a new or reproduction part from AMK.

Reproduction exhaust pipe to exhaust manifold nut for the Mercury Cougar or Ford Mustang and they are sold individually.Ford part # 376420-S.

Reproduction exterior convertible boot moulding / trim nuts for the Mercury Cougar or Ford Mustang and Torino. Here's another great reproduction brought to you by WCCC! Each vehicle will require 20 nuts. Sold individually.

Reproduction nut that replaces Ford part # 34033-S. This is the nut that secures the pitman arm to the steering box. Has correct 7/8"-14 threads. Split washer also needed, not included, nut only.

This is our reproduction quarter panel extension nut for the Mercury Cougar or Ford Mustang. These are sold individually.Replaces Ford part # 373556-S. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...

Replaces Ford part # C2DZ-6A529 Sold Individually.

Four nuts per bucket seat, 8 total nuts per car with bucket seats. Sold individually. Replaces Ford part # 378643-S. Phosphate & Oil (gray & black) finish

Unlike our reproduction nuts these good used original nuts can be purchased individually and they cost less to boot! 8 required per car, 4 per bucket seat.

Course threaded nut for most 1969-73 automatic shift arms. This is the nut that sticks down from the bottom of your automatic floor shifter and the nut connects the shift rod that goes to your FMX transmission. 3/8-16 locking flange head nut. 

New 3/8-16 nut for the shock tower shock cap. Three nuts used on each cap, 6 total per car. Sold individually.Replaces Ford part number 377706-S7.

Nut for attaching the steering wheel on any 1967 Mercury Cougar or 1965-67 Ford Mustang.Ford number 350983-S.

Perfect fit.

Correct nut that is designed not to come undone.

These were used to attach the taillight assembly to the tail panel on a 1969-70 Cougar. Five were used per taillight, 10 required in all for one car. Sold individually. Also the same size for 1967-68 tail lights.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a...

These are the little 11/32" lock nuts (sometimes called speed nuts) that you use to attach the taillight bezel to the taillight housing. 10 nuts per bezel, 20 per car.

C7WB-13753-A Grade-A used screw on nut or bezel for the dash toggle switches on 1967-68 Mercury Cougar XR-7, 1971-73 Mercury Cougar, and 1969-70 Mustang Shelby console switches. This is a perfect used part, if you need an average quality used one mention it when you make your order and we will try and locate a free one for you.

New torque converter nuts for connecting torque converters to flex plates on 1967-73 Mercury Cougar or 1967-73 Ford Mustang or other Ford Lincoln Mercury that is not metric. 3/8-24 threads, Grade 8 nut with a 9/16 inch hex. 0.79" OD and 0.39" thick. Torque converters use 4 nuts for attachment.Ford number 377704-S

34392-S7 5/16 inch nut for 1967-68 Mercury Cougar and Ford Mustang vent window pivot assembly. 1 per side.

Reproduction pair of snap nuts for attaching the hood latch support to the hood latch on the 67 - 68 Cougar. 

Set of 4 reproduction torque converter nuts for the Mercury Cougar or Ford Mustang.

These nuts and little red insulators are needed when installing the factory Amp gauge. Sold as a pair (2 nuts and 2 insulators). 

New plastic nut or insert for those 1/4 inch square holes in the grille for attaching the headlight doors (8 required there), and for the XR7 door pull panel mounting plates for attaching the actual door handles (2 required per side). Replaces Ford part # 379830-S1. Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in your Cat? The videos below are your ticket! ...

Correct size and style white square plastic insert that clips onto front or rear license plate bracket on any 1967-73 Mercury Cougar. Each kit allows one license plate to be mounted. The actual screw has a large head which is made for license plates, but is not the factory Ford style of fastener for Concours judged cars. We also sell an accepted original style of screw, see item 8286.

Reproduction heater duct nylon rivet #375064-S is sold individually.

New rubber "O" ring for Ford V-8 distributors from 289/302/351W/351C/429 engines.

New O-ring gasket for the 1967-68 Mercury Cougar flip trunk lock cylinder. Lock cylinder must be removed from the trunk lock housing to install. Original O-rings are normally cracked and broken when we disassemble them. 

Brightens the engine compartment and looks sharp. Fits our big block finned aluminum valve covers (item# 26018) and others with the round push-in style opening. Requires a rubber grommet to fit into the valve cover, which is usually included with new valve covers.Does NOT fit valve covers with the "stovepipe" fitting (like our small block finned aluminum units) or factory valve covers the tabs for twist-on oil caps. This cap is for after market valve covers.

Brightens the engine compartment and looks sharp. Fits aftermarket valve covers only. These require a rubber grommet to fit into the valve cover. Please Note: This oil cap DOES NOT fit the finned "G" valve covers we sale, as they are built to OEM specs.

These decals are cut to fit the 1968 end caps. The 1967 end caps had a larger woodgrain insert without a black border. We also sell a slightly larger version of this kit for the 1967 owners. Simple peel-and-stick installation. Here’s a little inspiration for you to get our vinyl overlay kit and wrap your own parts! ...

These fasteners were used to keep your package tray in place. In 1969 - 1970 the two clips were held in place with screws. Sold individually. We have seen various tech type screw with both large and small heads on them for fastening these clips. Same clip as was used in 1967-68, but without the push clip. We try to supply the screw, but you would likely want to get fresh ones, they are nothing special.Replaces Ford part number C4AB-6246698-A.

These fasteners were used to keep your package tray in place. In 1971 - 1973 three clips were used, held in place with screws. Sold individually.

These fasteners were used to keep your package tray in place. In 1967 - 1968 two T shaped fasteners were held in place with a spring clip. Sold individually. Ford part number C4AB-6246698-A

Reproduction disc brake pedal pad for the 1967 Mercury Cougar or 1965-67 Ford Mustang equipped with the automatic transmission. This is identical to the 1968-73 pad, just slightly narrower. 1968 was the introduction of many Federally mandated safety upgrades, the larger pedal being one of them. Replaces Ford part # C5ZZ-2454-C.

Reproduction disc brake pedal pad for the Mercury Cougar or Ford mustang equipped with a manual transmission. This unit is a perfect fit! Replaces Ford part # C5ZZ-2454-D.Fits: 1967 Mercury Cougar1968 Mercury Cougar 1969 Mercury Cougar 1970 Mercury Cougar 1971 Mercury Cougar 1972 Mercury Cougar 1973 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang 1969 Ford Mustang 1970 Ford Mustang 1971 Ford Mustang 1972 Ford Mustang 1973 Ford Mustang ...

Quality reproduction. Replaces Ford Part #: C5ZZ-7A624-B. Dear Lin Thurston, Hi, just wanted to let you know how impressed I am, to receive a package ordered on 6-6-07 and have it arrive on 6-13-07 all the way up here in Ontario Canada. That is impressive! Your shipping department is to be commended. I must say that the mail service worked at part of it, but the speed at which your firm addresses online orders from outside your country will keep me coming back for other items! Thank you, Phil...

This great fitting reproduction emergency / parking brake pedal pad for the Mercury Cougar or Ford Mustang. This is supposed to have a stainless steel retaining ring around the perimeter. We carry both reproduction and used. Replaces Ford part # C9ZZ-2454-A.

Reproduction foam rubber donuts that help cushion the brace from the tail panel on any 67 - 73 Cougar or Mustang.Replaces Ford part number C5ZZ-6540996Sold as a set of 4.

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. This ORR LAC chassis black paint will give the appearance of an expensive, baked on finish. Also usable on other tools, equipment, vehicle frames, shop racks, trailers and more. ORR-LAC 923 Semi Gloss black.

Replacement cork pan gasket for all 1965-73 C4 Ford transmissions. 

Cork pan gasket for the C6 transmission on any 1967-73 and 1967-73 Mercury and Ford. Rubber gasket also available.