1973 Mercury Cougar

Covers the metal, foot operated headlight dimmer on the driver side floor pan. Replaces ford part #: C5ZZ-13533-A.

This cowl is made for a car without AC but all you have to do to modify for a factory AC car is plug the vent hole on the driver side. Replaces Ford part # D1ZZ-6502010-A.

Plastic driver side vented cowl cover for the 71 - 73 Cougar. This panel snaps into place in the opening to the cowl vent to keep debris from going in and clogging the passageway. Ford Part Number D1ZB-65018A17-AB

Plastic passenger side vented cowl cover for the 71 - 73 Cougar. This panel snaps into place in the opening to the cowl vent to keep debris from going in and clogging the passageway.  Ford Part Number D1ZB-65018A17-AB

Crankshaft oil slinger for all small block Ford V-8's, starting 1963 until at least through 1973. 1963-68 289 and 289 HiPo engines. 1968-73 302 engines, 1969-70 Boss 302 engines, 1969-73 351W engines. Goes on the crankshaft after the timing gear and before the timing chain cover. It does have a purpose on the vintage engines. Outside diameter about 2-7/8 inches. Ford part number C3OZ-6310-A.

Crankshaft oil slinger for all 351C or Cleveland engines. Goes on the crankshaft after the timing gear and before the timing chain cover. It does have a purpose on the vintage engines.  Ford part number D0AZ-6310-A.

CRC contact cleaner is intended for cleaning sensitive electronics and electrical equipment. Great for cleaning edge connectors, buss bars, circuits, contacts, printed circuit boards, switches, circuit breakers, etc. Safe on most plastics.

For all 1971 to 1973 Cougars and Mustangs with H code 351-2V and FMX automatic transmissions.  Ford part number D1ZZ-6A023-B.*NOTE* Two notes - There is a difference between 1969-70 and 1971-73 FMX cross members. Additionally, Ford did produce H code 351-2V engines with C-6 transmissions. Triple check.

This listing is for a pair of walking cat die cast chrome cufflinks. These would be great for the serious collector who may want to add a bit of Cougar flair to outfit when hitting the town, or simply just another bit of memorabilia to add to their collection.  Walking Cat measures 1-3/16" across.

Parking brake return spring cup for the 69 - 73 Cougar or Mustang. This cup sits at the end of the spring and is held in place by an adjusting nut. It's used to keep the spring from sliding off of the front emergency / parking brake cable.

Custom made Walking Cat belt buckle for the Cougar die hard. This would make a great gift for anyone who lives and breathes everything Cougar. The buckle is bare, unpainted and ready for you to customize how you see fit. We're not sure how we ended up with this awesome collectable, but it's definitely one of a kind and the only one we know of, so when it's gone it's gone!  Measures 3 3/8" x 2 1/4"

1973 Front unibody cut with cowl. This cowl has the holes for the factory air conditioning. 1971-72 frame rails are constructed differently for the non-energy absorbing front bumpers.Excellent value! Please consider a front clip replacement for your vintage 1967-73 Cougar or Mustang - including fastbacks! No differences exist between the front understructures of a Mercury Cougar or Ford Mustang year for year. How many hours of labor is needed to replace individual aprons, towers, radiator...

1973 Front unibody cut with cowl. This cowl has the holes for the factory air conditioning. 1971-72 frame rails are constructed differently for the non-energy absorbing front bumpers.Excellent value! Please consider a front clip replacement for your vintage 1967-73 Cougar or Mustang - including fastbacks! No differences exist between the front understructures of a Mercury Cougar or Ford Mustang year for year. How many hours of labor is needed to replace individual aprons, towers, radiator...

Comes with good shock towers, front aprons, and core support. This is a great value for those that need to replace multiple parts upfront as you will not only get factory joined parts that will save you money and time, but it will also  preserve the value of your car. With a clean Western cut like this, one should be able to install it so that nobody would ever know your car has had anything replaced. You will have to call to order this one. Expect to pay about $300 for crating and...

Single cylinder head from 1970-73 Mercury Cougar with H code 351C-2V engines. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 2.04 and 1.65 inch valves, and the chambers measure out at 78.2 cc's. These are considered 'Open Chamber Heads'. With stock pistons, these heads will net an approximate compression ration of 9.5:1. Basic cylinder head number is 6090. Several Ford casting numbers were used, including the common D0AE-J. 2V in the...

Single cylinder head from 1972 Mercury Cougar with Q code 351C-4V engines. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 2.19 and 1.71 inch valves, and the chambers measure out at 75.4 cc's. These are considered 'Open Chamber Heads'. With stock pistons, these heads will net an approximate compression ration of 8.6:1. Basic cylinder head number is 6090. Several Ford casting numbers were used, including the common D1ZE-6090-GA. 4V in...

This "D" clip is larger than that found on the Mustangs and 1967 Cougar because it not only hung the wiring loom on the driver side of your engine compartment but also the vacuum lines going to the headlight switch. This clip is also found under the starter solenoid and under dash. We think that it is Ford part number 382184.

This "D" clip is larger than that found on the Mustangs and 1967 Cougar because it not only hung the wiring loom on the driver side of your engine compartment but also the vacuum lines going to the headlight switch. This clip is also found under the starter solenoid and under dash.

Used highly collectible Dan Gurney slot car racing track made by the Republic Tool and Manufacturing Corporation in Los Angeles California. Open box and lightly used. Both cars are intact, and the decals have been placed on the the vehicles and the track. Everything is good condition, but the cars have not been tested and the red car has had it's wheels painted. Other than that, this is a rare and truly great find. Features the Mercury Cougar Logo on front of the box.

Used metal dash support brace for all 1971-73 Mercury Cougar and Ford Mustangs. Fastens to the lower flange of the metal dash panel and attaches to the inner cowl, 10 inches long. Replaces Ford part numbers D1ZB-6504672-A.

This actually is a pretty impressive part once installed. It fits snug (very tight) over your existing cracked dash and you affix it by putting silicone around the perimeter. Unlike the 67-70 there is no stitched edge or speaker holes in the 71-3 so it is a perfect candidate for this cover. The good thing about this unit is that your dash pad can have large chunks missing and it still will work! You can install this without removing the dash and it is very hard to detect once in place. Made of...

Good used textured steel dash panel, for all 1971-73 Mercury Cougar and Ford Mustang. This is the flat steel piece that the meets the windshield and houses the defroster nozzles for the windshield.  Attaches to the dash pad using (5) 45271-S36 nuts.*Note - Save your VIN tag from your original dash, you don't want to lose it.Replaces Ford part number D1ZZ-65044D90-A. ...

Used wire set for the dash plug from the main under dash wiring harness from any 1971-73 Mercury Cougar. Wire colors may vary.

Quality Kenwood speakers that features two 40 watt 3 1/2" coaxial two way speakers. this unit is a huge improvement over the factory single speaker and no modifications needed. This unit is for all 1967-73 cars with in-dash factory AC or not. In Non-A/C cars, this speaker may partially crush the vent duct tube.Check out the "Cougar Dash Surgery, Clock and Speaker Install" video by Andrew Chenovick: ...

Since at least 2 speakers (channels) are required for stereo radios, this speaker system has been developed for classic vehicles that came with only one mono speaker. These dual voice coil "DVC" speakers will give you the best possible sound from your original speaker location. DVC speakers have up to 70% more cone area than the conventional dual speaker assemblies giving you improved bass response and 140 watt power handling. Both stereo channels connect directly to one speaker with dual...

This plate allows you to install (2) 3 1/2" speakers of your choice in place of the (1) original factory speaker in the dash of your Cougar or Mustang. This is the same plate used on the Kenwood and Pioneer Dual Dash Speaker kits.Check out the "Cougar Dash Surgery, Clock and Speaker Install" video by Andrew Chenovick: ...

Features two 4 ohm 3 1/2" coaxial two way speakers. Huge improvement over the factory single speaker and no modifications needed. This unit is for all 1967-73 cars with or without in-dash factory AC. In Non-A/C cars, this speaker may partially crush the vent duct tube.Check out the "Cougar Dash Surgery, Clock and Speaker Install" video by Andrew Chenovick: ...

Used switch panel for most 1971-73 XR7 convertibles. Panel holds 3 different toggle switches: COURTESY - MAP - TOP. All came painted black with the camera case finish with the indicated switches as shown. Most will be nearly pit free as shown but will need a spray of black paint for that 'extra' detail prior to installation.  *Note excludes all coupe or hard top Cougars, and non-XR7 convertibles.Replaces Ford part number D1WY-7604338-A.

Used switch panel for most 1971-73 XR7 hard tops. Panel holds 3 different toggle switches: COURTESY - MAP - R.DEFOG. All came painted black with the camera case finish with the indicated switches as shown. Most will be nearly pit free as shown but will need a spray of black paint for that 'extra' detail prior to installation. This panel does have a small hole above the defog switch for the red indicator light. Red indicator light sold separately. *Note excludes convertible and those Cougars...

Used switch panel for most 1971-73 XR7 hard tops. Panel holds 3 different toggle switches: COURTESY - MAP - ACCY. All came painted black with the camera case finish with the indicated switches as shown. Most will be nearly pit free as shown but will need a spray of black paint for that 'extra' detail prior to installation.*Note excludes convertible and those Cougars with the heated back lite or rear defog option.Replaces Ford part number D1WY-6504338-A.

Reproduction 351 4V AT / MT Emission (Before 1-73) for the 1973 Mercury Cougar / Ford Mustang

Reproduction 351 4V MT Emission (After 1-1-73) for the 1973 Mercury cougar / Ford Mustang

Engine code decal for the 351 with a 2 barrel carburetor and air conditioning.Stamped with engine code K604CG.

Here is another great product form Permatex. This decal and adhesive remover removes bumper and window stickers, tar, sap, bugs and other gooey substances. 

This is a reproduction of the original decal that contains the word "FRONT" that was located on the front of the air cleaner.Fits the following models 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar1971 Mercury Cougar1972 Mercury Cougar1973 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang1971 Ford Mustang1972 Ford Mustang1973 Ford Mustang ...

This is a reproduction of the original service instruction decal that was located on the side of the air cleaner.Fits the following models:1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...

Controversy abounds on which shrouds received these and which did not. It is our understanding that no early Cougars came from the factory with this decal installed. This decal first surfaced when Ford had major problems with their flex fans in the early 1970's. We will let you decide if it is correct for your application... This is placed on the top, center of the fan shroud.

Reproduction Detroit Locker Glove Box Decal for the 1967, 1968, 1969, 1970, 1971, 1972 and 1973 Mercury Cougar

These are our 2-inch diameter round decals to customize the plastic Legendary Wheel Co. center caps that come with their wheels. These caps are also available separately, see item # 30529. Nice quality vinyl that will last outdoors, and the graphics have a mirror finish to compliment the chrome. *If you're buying a set of Legendary Wheels from us, mention this item in the notes and we'll include them for free! ...

New "Mercury" script decal in black for any Mercury, but will be at home on the Cougar. Measures 10 3/4" wide by 1 1/2" tall.This is a die-cut vinyl decal. To install, you'll have to peel off the backing, apply the decal to the intended clean surface, press in place with a plastic squeegee or credit card, then carefully peel away the top contact paper.

This is the decal used on the button of the female seatbelt buckle. Each seatbelt uses one of these. Sold as a Pair. Replaces Ford Part #: C8AZ-65611C02-A. Check out our video "All about seat belts" below. ...

This walking cat decal measures 10.5" x 3.65".

This walking cat decal measures 10.5" x 3.65". Check out the very first Cougar in our video below!

This walking cat decal measures 10.5" x 3.65".

This walking cat decal measures 10.5" x 3.65". Check out the very first Cougar in our video below!

Die cut vinyl decal in black. Measures 6 3/4" X 2 1/2". Adhering this decal to either the inside or outside of the glass will dictate whether it is a right or left facing cat. Pictured below is Robin Miller's "G-Force" Cat! Click on images to enlarge. Check out this video of our 2013 Open House event! ...

Die cut vinyl decal in black. Measures 6 3/4" X 2 1/2". Adhering this decal to either the inside or outside of the glass will dictate whether it is a right or left facing cat. Check out the very first Cougar in our video below!