1973 Mercury Cougar

This kick down rod works on all 2 barrel Clevelands with the FMX transmission. This reproduction rod is made from stainless steel and weighs slightly more than the original. Please note that this item is drop-shipped from the manufacturer for domestic orders and will need to ship to us, then be shipped on to you for international orders.

Black ABS plastic replacement kick panels without speaker pods. Sold as a pair. Reproduction kick panels made for 1971-73 Ford Mustang, but will fit a 1971-73 Mercury Cougar OK.

Reproduction insulation located behind the kick panels on the 71 - 73 Cougar or mustang. Correct cut allows access to the door hinge bolts.

Premium grade used outer (tuner / volume) knob with no missing chrome or cracks. Two required per car, sold individually. We also have knobs with peeling chrome, we are happy to throw a damaged knob in for free with your order, just ask! We also have reproduction sets available.Ford part # D1ZZ-18817-A, and Ford casting # D1ZA-18822-AA.

1971 - 1973 Cougar wiper control switch knob. In early (May 3, 1971) Mercury changed the knob. This is the later knob. Hex shaped knob, good used, may show some minor wear.

Perfect set of four radio knobs for your Mercury Cougar or Ford Mustang. Very hard to find with flawless chrome as most are peeling bad enough to cut you if you are not being cautious. Ford part #'s D1ZZ-18817-A for the outer (tuner / volume) knob, Ford casting # D1ZA-18822-AA for the outer (tuner / volume) knob. D1ZZ-18830-A for the inner (balance / tone) knob, Ford casting # D1ZA-18A932-AA on the inner (balance / tone) knob.*TRIVIA* Did you know that Ford called the outer (balance / tone)...

This is the factory Ford remote trunk latch as used on luxury cars such as Thunderbird or Lincoln. As you can see from the photo, they are made (and install) exactly like our Cougar trunk latches, but with the addition of a release tab. These can be installed to use either a cable, vacuum, or solenoid release.

This wheel is inspired by the 1966 Shelby GT350 10 spoke alloy wheel. This updated design was created using state of the art casting technology for superior strength and precision. Each wheel features a CNC machined face with gloss black accents and a clear coat finish. These wheels take a specific shouldered 3/4" lug nut, find them here. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking...

The 1967 Cougar was Mercury's attempt to enter the Pony Car market segment popularized by the April 1964 introduction of Ford's Mustang. Introduced in the fall of 1966 for the 1967 model year, the first-year 1967 Cougar exceeded all sales expectations with 150,893 units sold. It was selected as Motor Trend's 1967 Car of the Year. Legendary Cougar Magazine is dedicated to the first three generations of Mercury's luxury Pony Car. Each bi-monthly issue includes features on the first-generation...

We have a very difficult time keeping grade "A" 1973 tail light lenses in stock. This is a one year only design that is less protected than the 71-2 version and also is prone to cracking in between the clear and red portion of the lens. Let us know if you have extras to sell or trade! Replaces Ford part # D3WY-13450-B. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web...

Grade "B" 1973 driver side tail light lens. This is a one year only design that is less protected than the 71-2 version and also is prone to cracking in between the clear and red portion of the lens. Grade B lens will have 1 or 2 blemishes which may include a small crack, chip, discoloration, or other defect. Replaces Ford part number D3WY-13450-B. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in...

We have a very difficult time keeping grade "A" 1973 tail light lenses in stock. This is a one year only design that is less protected than the 71-2 version and also is prone to cracking in between the clear and red portion of the lens. Let us know if you have extras to sell or trade! Replaces Ford part number D3WY-13450-A. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of...

Grade "B" 1973 passenger side tail light lens. This is a one year only design that is less protected than the 71-2 version and also is prone to cracking in between the clear and red portion of the lens. Grade B lens will have 1 or 2 blemishes which may include a small crack, chip, discoloration, or other defect. Replaces Ford part number D3WY-13450-A. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an...

Driver side front turn signal and combination side marker lens. Clear color, fits 1973 Mercury Cougar all models. Grade A used. These are used and they will have some scratches or scuffs in the plastic.Using a product like Novus Plastic Polish really improves the appearance and helps make these shine.Replaces Ford part number D3WY-13209-A. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store...

Driver side front turn signal and combination side marker lens. Amber color, fits 1973 Mercury Cougar all models. Grade B used. These will have a defect, discoloration, small crack, or a star from road debris. Using a product like Novus Plastic Polish really improves the appearance and helps make these shine.Replaces Ford part number D3WY-13209-A.

Passenger side front turn signal and combination side marker lens. Clear color, fits 1973 Mercury Cougar all models. These are New Old Stock or NOS, but they will have shelf wear. Meaning light scratches or scuffs in the plastic. Using a product like Novus Plastic Polish really make these shine.Replaces Ford part number D3WY-13208-A. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of...

These plates show almost no wear and would look right at home on a show car.NOTE: The plates and plate numbers pictured are exactly what you'll receive.

These plates show average wear and can be used as is, or restored to look new.NOTE: The plates and plate numbers pictured are exactly what you'll receive. 

Used air cleaner lid for all 1973 H code 351-2V engines. About 14.75 inches in diameter. Ford part number for the air cleaner assembly is D3ZZ-9600-A. The air cleaner lid by itself doesn't have a number. lid will be in comparable condition to picture shown.

This engine compartment lamp differs from the 1971-72 models in that it uses a fusible link instead of a twist-lock white plastic fuse holder. This light mounts on the passenger side, the hood pad will have a square knock-out already cut. Replaces part # D3ZZ-15702-A, casting # D2ZB-15702-AAClick on images to enlarge. ...

New Old Stock Glove box or glove compartment light with switch. Fits 1971-73 Mercury Cougar and Ford Mustang. Used switch and wiring assembly, tested and working. Ford part number D1WY-14413-A. Fits 71 CougarFits 72 CougarFits 73 CougarFits 71 MustangFits 72 MustangFits 73 Mustang ...

This very rare part is unique to the 1972 - 1973 351-4V / 351CJ with C6. We have determined that this part only fits Mercury Cougar and Ford Mustang. Torino and mid sized Ford/Mercury use a different numbered part. Marked D2ZP-AB. Ford Part #: D2ZZ-7A256-A. Check out our video on rebuilding your shifter below: ...

Steering column locking gear. For all 1970-73 Ford and Mercury steering columns. Made of brass, has 8 teeth and is 7/16 inches thick. Fits fixed and tilt steering columns. Ford part number D0AZ-3E717-A.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Rod used for locking the 4 speed manual transmission in "Reverse". Connects to the lower tab of the steering column and the reverse control transmission lever shift arm. Prevents the transmission from shifting out of reverse when the ignition key is removed. Rod is about 13 inches long and was originally marked with a green paint mark.The 4 speed manual transmission, could not be ordered on the 351-2V engines. Only 351-4V's and 429CJ's in 1971, and 351CJ's (Q code) in both 1972 and...

Used trunk lock cylinder retainer clip for 1972 - 1973 Cougar. *Note - For use on cars built after 3-1-1972.

Reproduction locking pawl for the 1970 - 1979 Mercury Cougar or Ford Mustang that is equipped with a factory tilt steering column. This unit works in conjunction with a pin and is responsible for locking the tilt column in place. In many cases, the pin tends to move out of place and break or chip the teeth of the locking pawl. We have found that 3 of 4 tilt columns that we have disassembled have locking pawls with broken or chipped teeth.  Replaces Ford part # D0AZ-3B661-A. *NOTE*...

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Long block, factory Q code 351CJ-4V V-8 engine. 351 Cleveland engine rated at 266 Hp with 8.0:1 compression ratio in 1973. These engine blocks have the 4 bolt main caps. Likely 0.030" bored motor that may or may not have been in running condition when pulled. Guaranteed to be rebuildable. Complete engine less carburetor, exhaust manifolds, fan, distributor,...

This is a the economy version of our lower control arm assembly, with a spot welded on reinforcing plate. We are sorry, but we just cannot recommend this part. The Scott Drake premium version of this lower control arm is superior and costs less. In the picture, you can tell that it is lacking a rolled lip on the outer edge that the originals and the Drake Premium reproduction offers. This is a non-returnable item. Having issues with wobbly or loose steering? Check out our video on sloppy...

4 oz. tube of non-melting, water resistant grease for disc and drum brake hardware, hood hinges, window regulators, quarter windows, vent window hinges, pretty much whatever needs lubing. A little dab will do ya! Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! ...

Nice used original Rotunda, over the counter dealer accessory. Stainless steel construction, weighs just under 8 pounds with hardware. Actual dimensions are 20 1/2 inches wide, 48 1/2 inches long, and the back lip is 3 inches tall. Installation hole spacing is as follows. Rear spacing 47-11/16" on center, front spacing (nearest the rear window) is 47-9/16". The spacing on short sides are 18-3/4" on center. This rack was utilized for may years on many cars. The same company made them for...

Reproduction 14x6" Magnum 500 wheel for the Mercury Cougar or Ford Mustang. These are the best quality of the three different Magnum 500 wheels you will find on the market today. The chrome is not only brilliant, but it holds up great year after year. You may save a few dollars buying the other brands out there, but why? We now have Magnum 500 caps that sport the Mercury Logo with multiple background colors and the walking cat caps as well. Center caps and lugs are sold separate. *NOTE* Please...

Unfortunately we are not presently offering this wheel as the supplier has been consistently sending us inferior product and poor customer service at an ever increasing price. Please consider our Legendary wheel line, here is a video that shows more: ...

Reproduction 15x6" Magnum 500 wheel for the Mercury Cougar or Ford Mustang. Here is an oddball you will probably not find advertised elsewhere... The total width of this wheel is 6 7/8" with a 4" backspace.Center caps and lugs are sold separate. *NOTE* Please allow 4 to 5 weeks for delivery.NOTE! These wheels are intended to be balanced with a lugcentric adapter. They will not balance with a traditional cone spacer on the tire spin balancer. Many tire shops do not deal with classics and do not...

These off-shore Magnum wheels are supplied to us by Scott Drake. We no longer carry the US made version as the quality was VERY inconsistent. This wheel has a 4 1/4" backspace. We now have Magnum 500 caps that feature the Mercury Logo and the walking cat caps as well. Center caps and lugs are sold separate.   NOTE! These wheels are intended to be balanced with a lugcentric adapter. They will not balance with a traditional cone spacer on the tire spin balancer. Many tire shops do not deal...

SUPPLIER IS BACKORDERED ON THIS WHEEL UNTIL FURTHER NOTICE.New aluminum 15x7" Magnum 500 wheel with a 4 inch backspace for your Mercury Cougar or Ford Mustang.  Includes generic plastic center cap.

New aluminum 17x8" Magnum 500 wheel with a 4 inch backspace for your Mercury Cougar or Ford Mustang. A great way to reduce the un-sprung weight on your Cat or Pony and look great while doing it! This item also includes the center cap. Lug nuts sold separately, get them here.

This is a good used main power window wiring harness that passes through the firewall, travels along the passenger side engine compartment and mates the the rectangular power window relay. Fits 1971-73 Mercury Cougars with factory power windows. This is a Grade B harness that has been tested, inspected and repaired as needed. This harness will function properly, but will have some obvious repairs. We also sell a Grade A harness that will look much better for judging.Replaces Ford part number...

Original equipment 4 speed top loader transmission from a 1972 or 1973 Mercury Cougar with engine code Q - 351-4V only. This is a late transmission and was used starting 12-1-1971. Transmission code 5 on the door tag, this would be a wide ratio 4 speed transmission with a 2.78 ratio first gear.Ford part # D2ZZ-7003-H, casting # RUG-BJ1. Percentages of Cougars equipped with a manual transmission by year1967 = 18.5%1968 = 13.2%1969 = 10.5%1970 = 7.8%1971 = 2.8%1972 = 1.5%1973 = 0.7%Total for...

Hurst built 4 speed manual shift control assembly for any 1972 - 1973 Mercury Cougar or Ford Mustang. This will have the round Hurst shifter lever. Includes shifter mechanism, shift rods, and shift lever. All in used condition.Ford part # D2ZZ-7400-Assembly Check out our video on rebuilding your shifter below: ...

NOS master power window switch for 1973 Cougars and Mustangs. Five switch assembly - driver / passenger front and rear windows, and a master lock out switch. This is a service replacement master switch, the buttons are more rounded than the 1973 version. Still all works the same. NOS E0VY-14529-C.

Good used metal portion of the door panel. If yours is bent, or you're doing custom door panels, you will need these. These are for Standard level interiors only.

Good used metal portion of the door panel. If yours is bent, or you're doing custom door panels, you will need these. These are for Standard level interiors only.

This unique gasket is only slightly different from the driver side. The angle at the front is just a little different and notice it does not have a hole drilled for the remote mirror cable used on the driver side. This gasket was also used on the 1971 Ford Torino / Ranchero and Mercury Cyclone. This is an upgrade over the reproduction we carry for a 1969 - 1970 Cougar that has a passenger side Sport Mirror. The Ford Engineering number seen on the pad reads D1OB-17724-AA. Do you have questions...

Original used hard plastic sport mirror pad / gasket. Correct for driver side sport mirrors for the 1971-73 Cougar and passenger side sport mirrors 1970-73. Ford engineering # C90Z-17724-B and D1WB-17C701-AB. Do you have questions about installing a passenger side mirror or using Riv-Nuts? Have more questions about installing a passenger side mirror or using Riv-Nuts? Got a mirror lens that flops around in your Sport Mirror every time you hit a tiny bump in the road? WCCC to the rescue! ...

This used driver side (left hand) mirror pad / gasket for use with a standard manual adjust chrome mirror. This unit will not work with a painted sport mirror or any remote mirror. Ford Engineering # imprinted on pad is C7OB-17C701-AA or C8OB-17C701-A. Do you have questions about installing a passenger side mirror or using Riv-Nuts? Have more questions about installing a passenger side mirror or using Riv-Nuts? Got a mirror lens that flops around in your Sport Mirror every time you hit a...

New Old Stock Ford C4 or C6 transmission modulator valve for 1967-73 Mercury Cougar or 1965-73 Ford and Mustang. Also known as the throttle valve, this valve controls vacuum to the transmission as you press the gas pedal, and it will apply higher control pressure for better quality shifts at higher RPMs. Ford part number C4AZ-7A377-B.

Engine mount for all 1973 V-8 engines in 1973 Mercury Cougar and Ford Mustang convertible body styles only. 1973 only, and these only work with convertible engine frame stands. We occasionally have these in good used condition, normally only one side is broken or worn. In the long run we recommend converting to 1971 - 72 coupe engine stands and mounts. Purists and concours owners, we understand your needs. Used or NOS only, this part is not reproduced in the aftermarket. Ford part number...

Used passenger side (right hand) convertible top boot trim moulding / trim for the Mercury Cougar convertible. If it were not for the paint over-spray on the black stripe of the drivers side piece these would be ready to bolt on and go! This is the best used example we have ever had in stock. We have several sets in stock with moderate to heavy pitting that are reasonably priced. Ford casting number reads D1WB-76423A18-AA or D1WY-76423A18-A. *Note - This item is not correct for a Ford Mustang. ...