Interior

Molded rubber plug, seals access hole in the side of shift housing. Replaces Ford Part # : C5ZZ-7C147-B Check out our video on rebuilding your shifter below: ...

Floor shifter access plug. 1967-73 Mercury Cougar and Ford Mustang, also fits floor shift 1971+ Mercury Comet and Ford Maverick. Ford Part number C7ZZ-7C147-A. Check out our video on rebuilding your shifter below: ...

Used actuator for the seat back release on the 1971 - 1973 Mercury Cougar or Ford Mustang. This item is tested and will be in working condition. Left is the same as right, two required per car. Sold individually.

Ford called this part a 'sleeve'. Attaches to the lower shifter arm with a hitch pin. Has nice bushing, with correct nut, washer, and pin. The 1967/68 and 1969/73 versions are identical. The C1AA-7353-C sleeve has fine threads, the C9OZ-7353-A has course threads. Fits all 1967-73 Mercury Cougar and Ford Mustang, and we suspect many other Ford vehicles beginning in 1961. Check out our video on rebuilding your shifter below: ...

This is the arm rest base for the driver or passenger side on any 1971, 192 or 1973 Mercury Cougar with standard interior as well as some Mustang trim levels.  Also fits multiple other Ford /  Mercury cars of the same vintage.Replaces Ford Part Number: D1AB-5724144

These plastic backing plates are found on all 71-73 Cougars with standard interior. Since most Cougars had decor or XR7 interior we have a limited supply of these and cannot guarantee we can get the color you desire, but we will try to accommodate. Right is the same as left. Keep in mind these same parts can be found on many Fords and Mercury's throughout the 70's

Correct texture and molded-in colors, with steel insert molded into foam to increase strength. Extra thick vinyl skins. American made.

Correct texture and molded-in colors, with steel insert molded into foam to increase strength. Extra thick vinyl skins. American made. Replaces Ford part # D1ZZ-6524101.

Correct texture and molded-in colors, with steel insert molded into foam to increase strength. Extra thick vinyl skins. American made. Replaces Ford part # D1ZZ-6524100.

Correct texture and molded-in colors, with steel insert molded into foam to increase strength. Extra thick vinyl skins. American made.

Correct texture and molded-in colors, with steel insert molded into foam to increase strength. Extra thick vinyl skins. American made. NOTE: The color on this armrest is incorrect and is a darker shade of brown, rather than the correct ginger color. Replaces Ford part # D1ZZ-6524101.

Correct texture and molded-in colors, with steel insert molded into foam to increase strength. Extra thick vinyl skins. American made. NOTE: The color on this armrest is incorrect and is a darker shade of brown, rather than the correct ginger color. Replaces Ford part # D1ZZ-6524100.

Correct texture and molded-in colors, with steel insert molded into foam to increase strength. Extra thick vinyl skins. American made.

Correct texture and molded-in colors, with steel insert molded into foam to increase strength. Extra thick vinyl skins. American made.

Mini console or consolette ashtray, for 1971-73 Mercury Cougar or Ford Mustang. Has ball bearing rollers, and dual cigarette extinguishers. Color keyed to the console and interiors, include a desired color in the notes or comments section of your online order. We will try to find your color, easy to paint with vinyl paint.

Sold individually # 374212-S

Reproduction steering column bearing for the 67-73 Cougar or Mustang. The tilt columns take an upper and lower bearing, while the fixed column only takes an upper. Outside diameter: 1 1/2" Inside diameter: 1 1/4"*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Used lower steering column bearing for the 67-73 Cougar or Mustang. The tilt columns take an upper and lower bearing, while the fixed column only takes an upper. The upper bearing can be found here. Outside diameter: 1.500"Inside diameter: 1.060" *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Reproduction of the upper steering column bearing for your 67* - 73 Cougar or Mustang. One required per car. Fixed Columns only use the upper bearing, while the tilt columns used an upper and lower. You can find the lower bearing here. Outside diameter: 1 3/16 " Inside diameter: 15/16 "Thickness: 1/4" Replaces Ford Part Numbers: F23Z-3517, C1AA-3517-A, C3AZ-3517-A, C7SZ-3517-D, D0AZ-3517-A, F23Z-3517-B * - may not fit some 67 Mustang applications with a fixed column as these used Ford...

Used cigar or cigarette lighter bezel for 1971-73 Mercury Cougar and Ford Mustang. Ford part # D1ZZ-15052-A and D1ZB-15053-A

Lower dash bezel to the left of the steering column. This one is for those 1971-73 Mercury Cougars with factor air conditioning. Cars with only the heater option used a different bezel that has a hole for the vent cable. This bezel is blank, and only has the rectangular hole for the air conditioning vent register.Replaces Ford part number D1WB-65044A13-BC (cast on the part) or D1WY-6504393-B

Lower dash bezel to the left of the steering column. This one is for those 1971-73 Mercury Cougars without factor air conditioning. Cars with only the heater option had dual fresh air vents. This bezel is for the driver side fresh air vent register and control cable, it has a molded hole for the vent cable.Replaces Ford part number D1WB-65044A13-AC (cast on the part) or D1WY-6504393-A.

This trim ring that surrounds the glove box release button is often missing. Easily installs by snapping in place. Better fit than the reproductions out there.Replaces Ford part number C6OB-62060A12.

Reproduction headlight switch bezel for any 1971-73 Mercury Cougar and Ford Mustang.  Replaces Ford part number D1ZB-11649-AC.

Used headlight switch bezel for any 1971-73 Mercury Cougar and Ford Mustang. Good used bezel with shiny chrome. May have one small nick in the chrome or one broken plastic stud on the reverse.Replaces Ford part number D1ZB-11649-AC.

Replace that old, pitted, and cut up radio bezel with this quality concours part. This is a Mustang piece that will work on your Cougar but is slightly different. The easiest way to identify a Mustang bezel from a Cougar bezel is that Mustang had four mounting holes and Cougar had five. Will need slight modification to fit Cougar. Replaces Ford Part #: D1ZZ-18842-A.

Good used part with no peeling foil covering or cracks. Of the three studs on the back you can rest assured one if not two of the studs will have cracks or a portion missing. We also have these in grade "B" for $43.85. Contact us for the many options as we have over 50 in stock. We sell the metal woodgrain painted center section separate. ...

Good used part with a little peeling on the foil and this part will most likely have cracks. Of the three studs on the back you can rest assured one if not two of the studs will have cracks or a portion missing. Contact us for the many options as we have over 50 in stock. We sell the metal woodgrain painted center section separate.

Starting in 1972 the 'Fasten Seat Belt' warning light was relocated to the center of the dash for visibility of all occupants of the vehicle. This is the bezel only that fastens to the instrument clusters of all 1972-73 Mercury Cougar models.Replaces Ford part # D2WB-10D841-AB.

Reproduction wiper switch bezel for the 71 - 73 Cougar and Mustang. Replaces Ford part number D1ZB-17C564-AC.

Used wiper switch bezel for any 1971-73 Mercury Cougar and Ford Mustang. Good used bezel with shiny chrome. May have one small nick in the chrome or one broken plastic stud on the reverse.Replaces Ford part number D1ZB-17C564-AC.

New screw with a correct 3/8 inch hex head for installing all armrests for all years.

12 Point bolt for attaching the steering column coupler to the steering box. All 1967-73 Mercury Cougar and most all other Ford, Mercury, and Lincolns. One bolt used for fixed columns, two bolts used on tilt steering columns.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

New old stock seat belt bolt, has the "A" marking on the head. 1-3/8 inches long bolt for seat belts. Torks head, not sure of the exact placement in the car. Ford box has 'Campaign M9D Bolt' as the description.  Ford part number 382624-S100.

Used in multiple applications front and rear lap belts. Inner and outer, marked with a letter "B" in at least three known fonts. 1-3/4 inches long, 1/2 inch shoulder, Torx 50 tool for installation and removal.

Used on inner and outer rear seat belt bolts, four per car in 1970 -1971 and used only on the inner rears in 72 - 73 due to the addition of rear retractors. Used in conjunction with two red washer / spacers, marked with three known font styles of the letter "A". 1-5/16 inches long, Torx 50 is the tool for installing and removing.

Two per car, identified with the letter "D" in three known fonts. This bolt was used in conjunction with a chrome spacer / washer that is also marked with the letter "D". 1-1/2 inches long, 1/4 inch shoulder, use a Torx 50 for installation and removal.

Replaces Ford Part # 382626-S Sold individually

Screw for attaching steering column plate to floor board. Usually 4 are needed and go through the carpet and into the toe board. Correct finish and style of AMK bolt. Length 1 3/16"#14 Threads

Fits 1967 - 1973 Standard or XR7

Concours correct for 67, but a nice dress-up item for 68-73. Replaces Ford Part # 382627 Four bolts, four washers and eight rubber washers in mounting kit.

Reproduction bolts and washers for the shoulder belts on any 1969-73 Mercury Cougar or Ford Mustang. Includes 2 each of the "D" bolts and chrome thick washers. Quality AMK kit F-3563.

Used bracket for installing the rear interior panels on any 1971-73 Mercury Cougar or Ford Mustang convertible. One bracket per side. These brackets will have a bit of dirt and or rust on them, originally painted chassis black. Replaces Ford part number D1ZZ-76310A84-A. 

Longer arm than drum brake pedals. Comes with all mounting hardware. Pedal shipped bare, picture may show hardware and pedal pad with trim. Most of these pedals are dated as shown. It makes it fairly easy to identify them by year.

Core bucket seat frame bottom for the Mercury Cougar or Ford Mustang. This unit is the same from driver side (left hand) to passenger side (right hand) and is the same whether you have a standard, decor or XR7. The base is the same whether you have center release or side seat back release. The foam almost will always be deteriorating, or even missing, and will need to be recovered. These units will be solid core frames taken from a Western parts car but keep in mind they will always have a...

Core driver side (left hand) and passenger side (right hand) pair of bucket seats with side seat release for the Mercury Cougar or Ford Mustang. The seat frame is the same in the standard, decor or XR7 and are the same driver to passenger side. The foam almost will always be deteriorating, or even missing, and will need to be recovered. These units will be solid core frames taken from a Western parts car. Seat tracks are sold separately. Seat hinge covers and hardware available...

Core driver side (left hand) bucket seat with the side seat release lever for the Mercury Cougar or Ford Mustang. The foam almost will always be deteriorating, or even missing, and will need to be recovered. These will be solid core frames taken from a Western parts car. Seat tracks are sold separately. Seat hinge covers and hardware available separately. *NOTE* Want to save on shipping? If you only need the bottom portion of the bucket seat we can discard the upper portion. The...

Core passenger side (right hand) bucket seat frame with center seat release for the Mercury Cougar or Ford Mustang. This unit is the same driver to passenger side. The foam almost will always be deteriorating, or even missing, and will need to be recovered. These will be solid core frames taken from a Western parts car. Seat tracks are sold separately. Seat hinge covers and hardware available separately. *NOTE* Want to save on shipping? If you only need the bottom portion of the...