Heating & Air Conditioning

Air conditioning fan blower BARE clam shell assembly for any 1971-73 Mercury Cougar or Ford Mustang with factory A/C. Assembly comes as shown: fiberglass two piece housing, flapper door, and a couple of clips to hold it together. Grade B used will have a minor stress crack, and or small chips. The holes for attaching duct work also may have one hole blown out. See Grade A for a better condition version.

Air conditioning fan blower BARE clam shell assembly for any 1971-73 Mercury Cougar or Ford Mustang with factory A/C. Assembly comes as shown: fiberglass two piece housing, flapper door, and a couple of clips to hold it together. Grade B used will have a minor stress crack, and or small chips. The holes for attaching duct work also may have one hole blown out. See Grade A for a better condition version.

Air conditioning fan blower assembly for any 1971-73 Mercury Cougar or Ford Mustang with factory A/C. We offer this assembly to go along with the reproduction heater box with air conditioning. Assembly comes as shown: fiberglass housing, fan motor, fan motor mounting plate, fan wheel, fan motor resistor, and the one attached vacuum actuating valve. All components tested and working, housing used and may have a chip or small crack from 5 decades of use.

Tecumseh compressor for air conditioning systems for Mercury Cougars and Ford Mustangs. These should be professionally inspected or rebuilt and our compressors have all been in storage for some time. These Tecumseh compressors came with a front oil fill plug up until 1967, thereafter, they have a top fill plug. Top fill is the most common, and likely what you will receive, unless you specify the 1967 style with front fill. These units are shipped without pulleys, clutches, or valves. The...

York compressor for air conditioning systems for Mercury Cougar and Ford Mustang. These should be professionally inspected or rebuilt and our compressors have all been in storage for some time. Shipped without pulleys, clutches, or valves. The York compressor is constructed mostly of aluminum and is lighter than the Tecumseh brand compressor by 10 pounds. The York compressors are less common too, subject to availability. We often see part numbers on the York tag (which does not list a Ford...

New manufactured air conditioning condenser for any 1971-73 Mercury Cougar or Ford Mustang. Condenser only, you will need to re-use or purchase a new dryer and possibly other components. 

Used air conditioning connecting duct or manifold. This plastic manifold mounts behind the center dash vent. Ford calls it a 'duct and connecting assembly' or 'A/C junction'. Grade 'A' condition, ships without cracks, splits, or broken tabs. Original factory or 'integral' air conditioning part.Ford part number D1ZZ-19C932-A.

Reproduction A/C evaporator for your Mercury Cougar or Ford Mustang.*Note - We have had numerous customers complain that these don't fit exactly like the originals.As far as evaporators go, we highly suggest going with a good used evaporator over these new versions. What happens is this: These companies use more coils (35% more passes) which equals out to thinner metal, which also equals out to performance that's sub-par to a good used original evaporator.Click on images to enlarge. ...

Used air conditioning evaporator core for 1971-73. We only sell used coils that are clean and sealed and do not sell coils that have pest damage or have corrosion from a leaking heater core. Even though we stand behind these used units for 30 days, we still suggest that you pressure test them before installing as we all know what kind of labor is required to install one of these. 1971-73 evaporators have 2 male fillings, and the whole unit is made of aluminum, including the tubes.Ford part #...

Exact replacement to original drier that removes moisture and should be changed anytime system is recharged. It really is the life of your system. This stainless steel filter element stops contaminants from clogging the expansion valve.

High quality and correct looking air conditioning discharge hose for Mercury Cougars or Ford Mustangs. This hose is compatible with both 134a and R12 refrigerants.

Regardless of which V-8 engine, D1ZA-19972-AA or D1ZA-19972-AB part number. This hose is approximately 24 inches long. These used hoses probably still hold pressure, we suggest a purchase of new 'O' rings prior to installation.

For Mercury Cougar and Ford Mustangs with integral or factory installed air conditioning with any V-8 engine. Original condensation drain hose from the A/C case, through the floor board, to the ground. Correct "S" shaped moulded hose with restrictor intact. Almost the same hose as was used 1969-70, Dearborn assembly line hoses have a ribbed section 1971-73. The 1969-70 versions, typically have the alligator texture on the outside of the hose.  Ford part # C9ZZ-19858. ...

Click on images to enlarge. Includes Sight Glass Hose (Ford Part # D1ZA-19837-A), the sight glass (Part # SG3, D2AZ-19D695-BK or YF-342). One of the major differences between the reproduction and the original sight glass hoses, is that the texture of the originals was much more defined.  You can see and feel the ridges in the hose on the originals.  Below is a close up picture of repro and used side by side, and it is obvious that the repro is not nearly as textured as the originals...

Good used hose that connects the sight glass hose to the Air Conditioning Dryer. Includes the sight glass to dryer hose (Ford Part # D1ZA-19835-A), 2 o-rings (Part # L33,D2AZ-19D695-R or YF-368 and Part # H33, D2AZ-19D695-AE or YF-316) and a quick connect (Part # QF3,C1SZ-19B696-A or YF-241 and Part # QM6, C1SZ-19B695-A or YF-252).

High quality and correct looking air conditioning suction hose for the Mercury Cougar or Ford Mustang.This hose is compatible with both 134a and R12 refrigerants.

Regardless of which V-8 engine, D1ZA-19867-BC part number. This hose is approximately 49 inches long.

This is actually a kit which includes 2 hoses (Part # D1ZA-19835-A and Part # D1ZA-19837-A), the sight glass (Part # SG3, D2AZ-19D695-BK or YF-342), 2 o-rings (Part # L33,D2AZ-19D695-R or YF-368 and Part # H33, D2AZ-19D695-AE or YF-316) and a quick connect (Part # QF3,C1SZ-19B696-A or YF-241 and Part # QM6, C1SZ-19B695-A or YF-252). *Note we normally supply the new coupler with this kit. Regardless of which V-8 engine, this hose when assembled is approximately 78 inches long.Ford MPC kit #...

For 1972-73 Mercury Cougars and Ford Mustangs with the 351W engine. This is a Pitts manufactured pulley and clutch assembly with a pulley diameter of 6-5/16", a clutch diameter of 5-1/8", and an overall thickness of 1-11/16 inches. Whew boy, say that 5 times fast!Ford part # D2ZA-2981-A. May also have part numbers of D2ZA-2981-A1A, D2ZA-2981-A1B, or D2ZA-2981-A2A.

Stud that the factory line workers used for locating the air conditioning pedestal bracket. Then backed up with a nut. Used on 351C / 429CJ pedestals from 1970 - 1973.*Note - Excludes 289 / 302 / 351W / 390 / 428CJ engines.

Reproduction stud and nut assembly that the factory line workers used for locating the air conditioning pedestal bracket. Then backed up with a nut. Used on 289 / 302 / 351W / 390 / 428CJ pedestals from 1967 - 1973. Stud is threaded into the cylinder head for easy installation of the cast iron pedestal bracket.*Note - Excludes 351C and 429CJ.

Complete heater and A/C control assembly includes bezel or face plate, bracket control mounting plate, electrical and plastic vacuum switches. Functional, driver quality, heater control assembly. This unit is for 1972-73 Cougars and Mustangs produced after 1-3-1972. The prior years 1971-72 assembly without the plastic vacuum switch assembly will fully interchange with this unit. Knobs and light socket wiring harness not included. Ford part # D2ZZ-19980-A. *RESTORATION TIP* If you like to...

Lower dash bezel to the left of the steering column. This one is for those 1971-73 Mercury Cougars with factor air conditioning. Cars with only the heater option used a different bezel that has a hole for the vent cable. This bezel is blank, and only has the rectangular hole for the air conditioning vent register.Replaces Ford part number D1WB-65044A13-BC (cast on the part) or D1WY-6504393-B

Lower dash bezel to the left of the steering column. This one is for those 1971-73 Mercury Cougars without factor air conditioning. Cars with only the heater option had dual fresh air vents. This bezel is for the driver side fresh air vent register and control cable, it has a molded hole for the vent cable.Replaces Ford part number D1WB-65044A13-AC (cast on the part) or D1WY-6504393-A.

Chromed plastic driver side fresh air "Vent" bezel. Mounts with the cable through a hole in the dash panel, just to the right of the vent register. Most all of these used bezels have a defect in the chrome plating along the bottom, not visible when installed.Replaces Ford part D1WA-18A405 (casting in the part), or D1WY-10852-B.*Note - Does not fit Mustang

Used heater blower motor for Mercury Cougars and Ford Mustangs with integral or factory air conditioning. These are good used original FoMoCo units and have the correct pigtails in place. This used unit also carries a one year warranty compared to the reproduction that carries a 30 day warranty. The mounting plate is included and mounted to the motor. On the reproduction units, the mounting plates are sold separately. These are the 1971-73 variety, which have specific colored wires and leads....

Reproduction heater blower motor for Mercury Cougars and Ford Mustangs with integral or factory air conditioning. These off-shore units may or may not prove to be as good of value as our good used original FoMoCo reconditioned units. Notice they do not have the correct pigtails in place. To date, all we can find for these cars are foreign made units. Keep in mind our used units carry a one year warranty and these new motors have a 30 day warranty. Also know that the mounting plate is included...

Used mounting bracket from a 1971-73 Mercury Cougar or Ford Mustang with factory installed air conditioning. This is the tab that is riveted to the blower housing, the stud goes through the firewall. Bracket with stud only, no other hardware included. Normally this will ship with the old fiberglass remnants still riveted to this bracket. 

Metal 2 piece bracket that mounts to the front of the radiator core support and separates the sight glass to dryer hose and the discharge hose from the condenser. Correct for 1971-73 Cougar and Mustang, and 1970-71 Torino, Cyclone, Ranchero, Montego.Replaces Ford part number D0OZ-19B632-A.

Used rubber bumper that fits into the bracket in the bottom center of the door shell. Fits all 1967-68 Mercury Cougar and 1965-68 Ford Mustangs. This is the rubber bumper for the window rest when the door glass is at its lowest. Bracket is in bottom of the center of the door. Fits both right and left doors. Correct for 1967 - 1968 but will work in 1969 - 1970 with Bolt-in glass if you cut it down. Sold separately, two required per car. Replaces Ford part # C5ZZ-6521762-B  Check out...

Heater cable for Cougars and Mustangs that are not equipped with factory air conditioning. Ford Part #: D1ZZ-18518-A

Used mounting and indexing bracket for the driver side fresh air vent cable on all 1971-73 Mercury Cougars without air conditioning. This bracket goes behind the dash panel and keeps the vent cable attached and indexed correctly. A 7/16-14  hex nut is also needed for mounting the cable. (Sold separately)Replaces Ford part number D1WY-6501822-A.

Used mounting bracket for the driver side fresh air vent cable on all 1971-73 Mercury Cougars without air conditioning. This bracket mounts to a tab on the fresh air vent, and keeps the cable stationary.  Replaces Ford part # D1WY-18C587-A.

Used steel bracket for mounting the passenger side fresh air vent cable to the bottom of the dash below the glove box. 1971-73 Mercury Cougar only.Replaces Ford part # D1WA-6501861-AC.*NOTE* Does not fit Ford Mustang.

Black plastic air conditioning center vent register bezel for any 1971-73 Mercury Cougar or Ford Mustang with Factory installed or integral A/C. Mounts Horizontally in the dash panel. Individual vents roll 360 degrees to blow air straight or to the sides. For that extra level of detail, we suggest using a silver paint pen for detailing the silver edges. Ford part number D1ZZ-19893-A.

Used air conditioning distribution chamber. Comes as shown, plastic housing, internal flapper door with rod, with attached bracket for attaching vacuum actuator. Actuator and hardware sold separately. Unbroken condition, it will definitely need new foam on the door.Replaces Ford part number D1ZZ-18471-A.

These are used hose clamps that bolt to the body and lateral A/C bracket. These were dipped in a rubber like substance to prevent chaffing. The ones that we have available may have some cracking or damage to this coating. It should be easy to 'dip' them again with the product that is available in most hardware stores. We normally see 2 of these clamps, securing the hoses on most cars. Replaces Ford part number 374125-S100.

Clips that attach to the dash for mounting the defrost nozzles. Package of 3 clips and nuts. Good for cars with or without A/C. Typically found on 69-73 cars, but will also fit and work on 1967-68 as well.Replaces Ford part number 357849-S100.

Original used female half of the factory air conditioning coupler for all 1967-73 liquid line or sight glass hoses. Brass construction, includes the plunger and spring. Also sold as a two piece kit which includes the male and female components. Replaces Ford part number C1SZ-19B596-A.

Original used factory air conditioning coupler for all 1967-73 liquid line or sight glass hoses. Brass construction, includes the plunger and spring. Sold as a two piece kit which includes the male and female components. Replaces Ford part number C1SZ-19B596-A and C1SZ-19B595-A.Components also sold individually.

Original used male half of the factory air conditioning coupler for all 1967-73 liquid line or sight glass hoses. Brass construction, includes the plunger and spring. Also sold as a two piece kit which includes the male and female components. Replaces Ford part number C1SZ-19B595-A.

Used rear window defog switch and knob assembly with mounting bracket for the 71 - 73 Standard Cougar.

Windshield defroster nozzle for Mercury Cougar and Ford Mustang with A/C. This is a grade "A" unit with no issues other than some discoloration.Ford part # D1ZZ-18490-B.

Windshield defroster nozzle for Mercury Cougar and Ford Mustang with A/C. This is a "B" grade unit and will have 1 or 2 minor defects. Defects such as a crack or a single broken tab. Will be an operational unit and is better than not being able to defrost your windshield.Ford part # D1ZZ-18490-B.

Windshield defroster nozzle for Mercury Cougar and Ford Mustang without A/C. This is a "B" grade unit and will have 1 or 2 minor defects. Defects such as a crack or a single broken tab. Will be an operational unit and is better than not being able to defrost your windshield. You will need to staple the flex part onto your heater unit. Very fragile part, almost always going to have Grade B, seldom will we have a Grade A used.Ford part # D1ZA-18A565-AD

Blower door for any 1967-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The blower door allows air to pass to the duct tubes from the center blower motor housing. Part cleaned for photograph, normally will ship 'as removed'. Inspected for excessive rust pitting or weakness of the metal, will have good rubber seal as shown. Door only, shaft not included, but available. See related parts.Replaces Ford part number C7ZZ-18B254-A.

Air inlet damper door for any 1969-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The damper door allows re-circulating or fresh air to enter the fiber glass A/C box. Dimensionally the same as the 1967-68 door, but with two small notches, instead of one. Part cleaned for photograph, normally will ship 'as removed'. Inspected for excessive rust pitting or weakness of the metal, they all will have a slight amount of metal degradation from being assembled as bare...

Evaporator door for any 1967-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The evaporator door allows air to pass over the evaporator in the A/C box. Part cleaned for photograph, normally will ship 'as removed'. Inspected for excessive rust pitting or weakness of the metal, they all will have a slight amount of metal degradation from being assembled as bare metal. Door only, shaft not included, but available. See related parts.Replaces Ford part number...