Body

Hex head screw for attaching floor drain hole covers. Several different screws were used over the years and at different plants. All seem to be a #8 sheet metal screw of varying lengths. This is a #8 hex washer head tapping screw with 5/8" length. Two screws per drain cover, 2 or 4? per car, not sure. We also have the drain covers. 

Reproduction driver side inner A pillar / kick panel for the 1971 - 1973 Cougar or Mustang.

Reproduction passenger side inner A pillar / kick panel for the 1971 - 1973 Cougar or Mustang.

This knurled nut is located under the front slides in each corner (1 per side, 2 per car) and is used to adjust the height of the sun roof panel.

This plate is what is located on the backside of your door jam where your striker threads in.Fits passenger and driver sides.

Threaded anchor that slides into the trunk hinge on each side. Sold individually, two needed per car. These are for Cougar and Mustang built before approximately 3/31/1971. Look for bolt spacing of 3 inches on those trunk lids.  Ford number 6242752. *Note - Trunks after March 31, 1971, used a different anchor plate. Bolt spacing of about 3 inches.

Threaded anchor that slides into the trunk hinge on each side. Sold individually, two needed per car. These are for Cougar and Mustang built after approximately 3/31/1971. Look for bolt spacing of 4-1/4 inches on those trunk lids.  Ford number C9AZ-6242752-A. *Note - Trunks prior to March 31, 1971, did not use this anchor plate. I think that they had a bolt spacing of 4-1/2 inches.

These plastic backing plates are found on all 71-73 Cougars with standard interior. Since most Cougars had decor or XR7 interior we have a limited supply of these and cannot guarantee we can get the color you desire, but we will try to accommodate. Right is the same as left. Keep in mind these same parts can be found on many Fords and Mercury's throughout the 70's

Correct texture and molded-in colors, with steel insert molded into foam to increase strength. Extra thick vinyl skins. American made.

Correct texture and molded-in colors, with steel insert molded into foam to increase strength. Extra thick vinyl skins. American made. Replaces Ford part # D1ZZ-6524101.

Correct texture and molded-in colors, with steel insert molded into foam to increase strength. Extra thick vinyl skins. American made. Replaces Ford part # D1ZZ-6524100.

Correct texture and molded-in colors, with steel insert molded into foam to increase strength. Extra thick vinyl skins. American made.

Correct texture and molded-in colors, with steel insert molded into foam to increase strength. Extra thick vinyl skins. American made. NOTE: The color on this armrest is incorrect and is a darker shade of brown, rather than the correct ginger color. Replaces Ford part # D1ZZ-6524101.

Correct texture and molded-in colors, with steel insert molded into foam to increase strength. Extra thick vinyl skins. American made. NOTE: The color on this armrest is incorrect and is a darker shade of brown, rather than the correct ginger color. Replaces Ford part # D1ZZ-6524100.

Correct texture and molded-in colors, with steel insert molded into foam to increase strength. Extra thick vinyl skins. American made.

Correct texture and molded-in colors, with steel insert molded into foam to increase strength. Extra thick vinyl skins. American made.

Improved reproduction pair of sun roof cables for the Mercury Cougar but they will interchange with most all early Golde / American Sunroof Corporation Moonroof / Sunroofs. Keep in mind this same basic cable design was used on many makes including Thunderbird, Lincoln, Mopar, BMW, Mercedes, Porsche and several other cars. (minor revisions were made through the years). These cables measure 64 1/2" tip to tip which may be too long for some applications. All examples we have found for the Cougar...

Good used solid panel with all parts removed. Panel measures 19.5" x 37". Whereas at first glance these may all look the same, the contour of the roof changes with the body style changes. Call us for price and availability on panels with varying degrees of repairable rust.

Grade B used panel with all parts removed. Panel measures 19.5" x 37". Whereas at first glance these may all look the same, the contour of the roof changes with the body style changes. Grade B will have some rust through in several places. 

Eight piece kit that includes inner and outer belt-line for both door and quarter glass. This kit contains enough for both pieces of door and quarter glass. These strips run horizontally against your glass and keep water and debris from entering your rear quarter panels and doors causing them to rust out. These kits include the correct stainless steel trim on the interior side strips. Old belt-lines will become hard and trap grit causing your glass to get heavy vertical scratches. You can...

Eight piece kit that includes inner and outer belt-line for both door and quarter glass. This kit contains enough for both pieces of door and quarter glass. These strips run horizontally against your glass and keep water and debris from entering your rear quarter panels and doors causing them to rust out. These kits include the correct stainless steel trim on the interior side strips. Old belt-lines will become hard and trap grit causing your glass to get heavy vertical scratches. You can...

Eight piece kit that includes inner and outer belt-line for both door and quarter glass. This kit contains enough for both pieces of door and quarter glass. These strips run horizontally against your glass and keep water and debris from entering your rear quarter panels and doors causing them to rust out. These kits include the correct stainless steel trim on the interior side strips. Old belt-lines will become hard and trap grit causing your glass to get heavy vertical scratches. You can...

Eight piece kit that includes inner and outer belt-line for both door and quarter glass. This kit contains enough for both pieces of door and quarter glass. These strips run horizontally against your glass and keep water and debris from entering your rear quarter panels and doors causing them to rust out. These kits include the correct stainless steel trim on the interior side strips. Old belt-lines will become hard and trap grit causing your glass to get heavy vertical scratches. You can...

Used driver side (left hand) rear marker light bezel for any 1971-73 Mercury Cougar. Originally painted body color, flush mounted to the passenger side rear quarter panel. Has two attaching studs, and sometimes one locating stud. We often times find that the locating stud is broken or cut off. You will want to cut the corner stud off if using the available reproduction Mustang red rear reflectors. All of our bezels will have the 2 larger studs intact. See related items for new lenses and...

Used passenger side (right hand) rear marker light bezel for any 1971-73 Mercury Cougar. Originally painted body color, flush mounted to the passenger side rear quarter panel. Has two attaching studs, and sometimes one locating stud. We often times find that the locating stud is broken or cut off. You will want to cut the corner stud off if using the available reproduction Mustang red rear reflectors. All of our bezels will have the 2 larger studs intact. See related items for new lenses and...

Metal reinforcing plate welded to the center of the rear body, where the 9 inch third member may come into contact with the floor. Cut from one of our many parts cars. Likely originally had a Ford part number of 4731. Removed from a 1971-73 Mercury Cougar, we suspect that it will not be a direct fit for a Mustang.This part will come as shown, spot welds will need to be drilled and the plate welded to your chassis.

These are about half the weight of originals and do not look correct in any way. They are far better than nothing. Bolts to the left hand and right hand lower floor reinforcement panels. Bolts into place with 6 hex bolts 3/8-16 x 1-1/8" with washers. These were painted satin black from the factory. Replaces Ford Part # C5ZZ-7610962-A. The Ford description of this plate is "Plate - Front floor lower cross member". All 1969 - 1973 Cougar convertibles and all 1965 - 1973 Ford Mustang...

57084-S Attaching bolt with 7/16" hex head and captured washer. Among other things, it is used to attach the door run, window stops (all 3), both window stabilizers, and the window regulator. Same bolts for manual and power window regulators. Bolt sold individually, there are a good handful in each door. This bolt is used for bolting in the bolt-in glass on 1970, lower "L" bracket for rear quarter windows on 1971-73 Cougar and Mustangs.

Used 1971-73 style bolt and nut for installing the shock tower brace to the cowl.

Reproduction bolts for the deck/trunk lid latch for the Mercury Cougar or Ford Mustang. This is a set of five bolts and will fit both the standard and XR7. Total of 5 bolts used 1969-73, 1967-68 Cougars will only use 2. We think that Mustangs use 5 on all years 1967-73. AMK F-227 Check out this video

Good used Western part that is not bent or heavily rusted and the left is the same as right. This is the round style and the round and the flat 1971-72 fender braces fully interchange.Ford master part # D3WY-16B134-A.

Sold individually, four required per car. Replaces Ford part #: C7AZ-5426528.

Aluminum housing for the sunroof cable drive, connects to the motor on any 1967-73 Mercury Cougar and many other vehicles that used the Golde sun roofs. Golde was a company from West Germany and also supplied parts to many other auto manufacturers such as Mercedes-Benz, Porsche, VW, BMW, Mopar, and Ford. ASC was the company that installed sun roofs for Ford US, and they used Golde components. Casting number Golde 100 413 600 / Golde 100-413-600 / Golde 100413600. ...

Aluminum cover for the sunroof cable housing on any 1967-73 Mercury Cougar and many other vehicles that used the Golde sun roofs. Golde was a company from West Germany and also supplied parts to many other auto manufacturers such as Mercedes-Benz, Porsche, VW, BMW, Mopar, and Ford. ASC was the company that installed sun roofs for Ford US, and they used Golde components. Casting number Golde 100 413 605.

Since we do not have near enough of these used inner panels to go around, we are offering this cardboard template for purchase for those of you that would like to make your own. With the template one should be able to produce a reasonable facsimile. If you are really talented and think you would like to make them in quantity let us know! We would be interested in purchasing them.

Two or three of these clips were needed per door to mount the padded armrest. Three were used per car for a total of six, on 1969-70 Cougar and Mustangs. Two used in 1971-73 on standard Cougars. Sold individually.Replaces Ford part # C6AZ-6224146-B.

Two or three of these clips were needed per door to mount the padded armrest. Three were used per armrest for a total of six, on 1969-70 Cougar and Mustangs. Two used in 1971-73 on standard Cougars. Sold individually.Replaces Ford part # C6AZ-6224146-B.

These are the plastic brackets that screw to you roof and then slide the vinyl colored piece over. Sold individually, four are required per car. Replaces Ford part # C8AZ-6229232.

Sold individually, black only. We have an array of colors in good used condition used. We also have the hard plastic bracket that this slips over. Four are required per car. Replaces Ford Part #: C8AZ-6229024-A.

Used driver side (left hand) coil spring cover that is a good solid western part for Mercury Cougar and Ford Mustang.Ford part # D1ZZ-3383.

Reproduction driver side (left hand) outer shock tower cover for Mercury Cougar and Ford Mustang. We cannot stand behind this product as it is an ill fitting reproduction, however do offer rust free used originals. No returns accepted.

Reproduction passenger side (right hand) outer shock tower cover for Mercury Cougar and Ford Mustang. We cannot stand behind this product as it is an ill fitting reproduction, however do offer rust free used originals. No returns accepted.

Used passenger side (right hand) coil spring cover that is a good solid western part for Mercury Cougar and Ford Mustang. Ford part # D1ZZ-3382.

* This is the closest available fit full floor pan for the 1969-73 Ford Mustang Convertible or Mercury Cougar Convertible, this pan will need modification to "make it fit." Complete floor pan for the 1969 - 72 Mercury Cougar or 1965-68* Ford Mustang Convertible. This item ships direct from the manufacturer for most orders and must be shipped via truck freight, and CANNOT ship via UPS. Shipping to business addresses tends to be less than residential addresses, sometimes substantially....

Complete floor pan for the 1969-70* Ford Mustang or 1969-70* Mercury Cougar. This item ships direct from the manufacturer for most orders. This item must ship via truck freight. Shipping to business addresses tends to be less than residential addresses, sometimes substantially.This item ships direct from the manufacturer for most orders and must be shipped via truck freight, and CANNOT ship via UPS. Shipping to business addresses tends to be less than residential addresses, sometimes...

Complete four piece door vapor barrier kit specifically cut for the year of your Cougar. Check out the video on replacing your door panels below.

Used to cushion and protect top vinyl from excessive wear from side rails. Replaces Ford part #: D1ZZ-7652875.

No excuses 100% complete mechanism with no cracks, missing parts or heavy corrosion. We can include the top cylinders but will not guarantee they will not leak. We carefully break this down by removing the header and crossbows and placing the original bolts back in the holes. Once you get this from UPS it will be very evident how it goes back together.