1973 Mercury Cougar

Used wiring pigtail that runs from the 14401 under dash harness to the heater switch w/ A/C on the 71 - 73 Cougar.

Used under dash wiring harness repair ignition switch plug and pigtail for your 1971-73 Mercury Cougar XR7. This is part of the 14401 main under dash wiring harness.

Used under dash harness repair plug and pigtail for the light switch harness for the Mercury Cougar Standard and XR7. This is part of the 14401 main under dash wiring harness.*NOTE* The individual wires can be removed from the block and other wires can be inserted if your car has different options.

Used wiring pigtail plug with wire lead leading from the under dash harness to the oil pressure gauge on the 1971 - 1973 Mercury Cougar XR7. The back of the gauge is marked with "white" and "green" for correct plug placement.

Used wiring pigtail that runs from the under dash harness to the passenger side door jamb switch on the 71 - 73 Cougar.

Used wiring pigtail that runs from the under dash harness to the seat belt warning buzzer on the 72 - 73 XR7 Cougar.

Used wiring pigtail that runs from the under dash harness to the seat belt warning light on the LATE 1971 - 1973 Cougar.

Used wiring pigtail plug coming from the under dash harness to the turn signal flasher on the 71 - 73 Cougar.

Used under dash wiring harness repair plug and pigtail to the turn signal switch for the 1973 Mercury Cougar, standard or XR7 model. This is part of the 14401 main under dash wiring harness. The connector plug changed for 1973, it got bigger.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question...

Used under dash wiring harness repair plug and pigtail to the windshield wiper switch for the 1971 - 1973 Mercury Cougar. This is part of the 14401 main under dash wiring harness.

Used wiring pigtail for the Windshield washer pump on the 1971 - 1973 Mercury Cougar or Ford Mustang.

Electrical wiring pigtail for the windshield wiper motors on any 71 - 73 Mercury Cougar or Ford Mustang. Plug with correct color wires and an adequate amount of wire length to make a repair or splice onto the newer motors without plugs.

Wiring pigtail for the low fuel sending units on 1973 Mercury Cougar XR7 and standard models with low fuel warning light, cut from a taillight wiring harness. The wiring is all integrated in 1973, unlike 1971-72 which has a separate harness for the fuel sending unit. The Safety Convenience Package included a low fuel warning light. This pigtail has three wires which attaches to the three prongs on the D1WF-9275-AC low fuel sending units. Ford part number is D3WB-14406-B or D3WY-14406-B. *Note...

Original stereo radio pigtail and plug. From a 1972-73 Mercury Cougar or Ford Mustang stereo harness. Has correct plug, wire colors and makings for the plug that connects to the factory stereo radio  *Note This is the speaker radio lead, from the speaker harness.

Reproduction wiring pigtail repair kit for the sequential box on the 1969 - 1973 Cougar.  Included are: 1 five pin red connector1 five pin black connector

Used plastic shield affixed to the quarter to protect the wiring to the power window switch. Left and right are the same.Ford Part Number D1ZB-14A099-BB

Reproduction Wittek tower hose clamp kit for the Mercury Cougar or Ford Mustang equipped with the 302 or 351 engine. This set of 10 clamps is concours correct and features the correct date stamps. It is often little details like this that separates first and second place when your precious Cat or Pony is being judged.

The Wittek Company manufactured the tower clamps used on the Cougar from 1967 to 1973, the Mustang from 1964 1/2 to 1973, as well as many other Ford and Mercury cars during that period. In October or 1993, the company filed for bankruptcy. This has made the tower clamp unavailable to the classic car restorer. Our supplier was able to bid at the auction for enough of the original tooling and parts to make these clamps available again. Other companies have also reproduced these clamps, but...

The Wittek Company manufactured the tower clamps used on the Cougar from 1967 to 1973, the Mustang from 1964 1/2 to 1973, as well as many other Ford and Mercury cars during that period. In October or 1993, the company filed for bankruptcy. This has made the tower clamp unavailable to the classic car restorer. Our supplier was able to bid at the auction for enough of the original tooling and parts to make these clamps available again. Other companies have also reproduced these clamps, but...

Listing is very good quality wood grain insert only. Plastic will be broken. The difference between 71 and 72-3 is that 71 has no provision at the top for the seatbelt warning light.

Reproduction wrench or crank, for manually closing the factory installed sunroof installed on any 1967-73 Mercury Cougar. Sunroofs, technically moonroofs, were originally installed by ASC or American Sunroof Corporation. Hertz 1968 XR7-G cars all came with factory sunroofs, as did the Hertz rental 1969-70 Cougar Eliminators. ASC also installed sunroofs in Ford Thunderbird, Lincoln MK III.ASC used Golde mechanical parts from Germany. Golde was a manufacturer of sliding canvas and metal roofs on...

Good original used toggle tip for the 1971 - 1973 Mercury Cougar XR7

This direct replacement is the 2 inch Y pipe only with 2-1/4 intermediate pipe outlets and is for any 1971-73 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2 inch aluminized pipes and made from an original 1971 Cougar and Mustang with the 351C 2V engine. We also sell OEM style dual exhaust systems that include the H pipe, mufflers, and tail pipes.*NOTE* Will not fit 1970 351 Cleveland engines. Please...

1973 Mercury Cougar and Ford Mustang shifter handle for automatic transmissions with selector button and set screw. Starting in 1973 Ford stopped using the deluxe handles with faux leather and eliminated the dummy button on the right side of the handle. Ford part numbers D3OZ-7213-A and 1973 black plastic push button. Check out our video on rebuilding your shifter below: ...

NOS (New Old Stock) rear pancake motor for the rear quarter windows of the Mercury Cougar or Ford Mustang. These motors are often ruined because water has leaked down into the quarter panel where it has then seeped into the motor. Once water gets inside the case, the motor's days are numbered. This is because the interior of the case will eventually start to rust and it will seize the motor. This motor is a service replacement part and it would have been the motor your local dealership would...

We recently unearthed a few of these unused club decals from the 1980's. "Cougars Northwest" was one of the earliest Cougar Clubs in the country. It folded back in 1988. It was amazing to witness the number of XR7G's, GTE's and Eliminators that would appear at the various club functions such as the annual "Cruise To Cougar Washington". Check out the very first Cougar in our video below! ...

NOS 1983 Ford manual on how to read and understand vacuum diagrams. Although it's technically made for older cars, it has tons of useful information on how to decode diagrams. Includes sections on vacuum theory and applications, devices, hoses, schematics and system diagnosis. This handy book has information pertaining to how the engine creates vacuum, the carburetor and it's vacuum pressure regulation characteristics as well as air intake, fuel induction, emissions and ignition. As an...

Are you looking to replace or upgrade your complicated 1968-70 3 Point Seat Belts with a modern easy to use factory looking Belt? These 3 Point Seat Belts will bolt onto any 1968-1970 Coupe using your existing mounting hardware... The belt buckles are very similar to the original Starburst buckles Ford used in the Late 1960's. Please keep in mind that although these are called "Parchment", they are more of a light brown / tan color. These belts are nice aesthetically, they don't fit very...

THIS ITEM HAS BEEN DICONTINUED BY THE SUPPLIER.A must for anyone planning to work on their own car. This book contains detailed instructions on disassembly and assembly of all major components. As seen on the front cover, this manual covers multipe makes of vehicles.The 1973 Ford Car Shop Manual is the original manual used by Ford mechanics to guide them through repairs and maintenance. Each section provides information on the operation of major systems, diagnostics, troubleshooting, overhaul,...

Decent reproduction of the air conditioning sight glass hose for the Mercury Cougar and Ford Mustang. Hose texture is not the same and the sight glass itself is different, but length and fittings are correct. If your sight glass hose is not original or you do not have the 2 piece quick disconnect, you may need to purchase the complete sight glass hose kit. For 100% correct hose, please see our good used sight glass hoses. Includes Sight Glass Hose (Ford Part # D1ZA-19837-A or...

This is actually a kit which includes 2 hoses, 2 o-rings, and a quick connect. When assembled this hose is approximately 78 inches long. The Ford Master Parts Catalog (MPC) kit number is C8OZ-19837-A.Sight Glass Hose to A/C Dryer Hose (Part # D1ZA-19835-A)Sight Glass Hose (Part # D1ZA-19837-A)Sight Glass (Part # SG3, D2AZ-19D695-BK or YF-342) 2 O-Rings (Part # L33,D2AZ-19D695-R or YF-368 and Part # H33, D2AZ-19D695-AE or YF-316)Quick Connect (Part # QF3,C1SZ-19B696-A or YF-241 and Part # QM6,...

For 1971-73 Mercury Cougars and Ford Mustangs with the 351W engine manufactured after 10-26-1970. This is a Pitts manufactured pulley and clutch assembly with a pulley diameter of 6-5/16", a clutch diameter of 5-1/8", and an overall thickness of 1-11/16 inches. Ford part # D1OA-2981-A. May also have part numbers D1OA-2981-AA, D1OA-2981-A1A, D1OA-2981-A1B, D1OA-2981-A2A, and D1OA-2981-A2B.

This A/C vacuum canister mounts to the passenger side shock tower and controls damper doors inside the A/C unit. This unit includes a built in check valve. Used and tested vacuum tank and bracket, also known as the A/C vacuum reservoir. Fits all 1971-73 Mercury Cougar, 1971-73 Ford Mustang, as well as 1970-71 Ford Torino / Fairlane and Mercury Cyclone Montego, 1970-7? Ford Maverick and Mercury Comet.Replaces Ford part # D0DZ-19A566-A.  

Used Wire lead for the accessory terminal found optionally on 71 - 73 Mercury Cougar and Ford Mustang fuse blocks. Lead comes with factory molded triple female connector for plugging in the various accessories such as 1969 swing away steering column, rear window defogger, speed or cruise control, etc. Wire will be marked with D1AB-14A318-AB

We will loan you this adhesive / epoxy applicator for 60 days, with a 100% refundable purchase price. Only available to customers that purchase our 3M bonding adhesive. Tool must be returned in undamaged condition with no missing parts within the 60 day time period.Returns past 60 days are subject to a 25% restocking fee. ...

New adhesive / epoxy applicator to apply our 3M window adhesive to the glass (or whatever else needs bonding) in your Mercury or Ford. This non-drip unit features an easy loading breech, a 1:1 mixing ratio and full cartridge support. We also offer a 60 day loaner if you only need this unit for a short time. ...

This stepped window trim clip is great for times when your stainless trim just will not click into place. We have found that the reproduction cougar rear window gasket is a little taller than OEM and this adjustable clip allows you to compensate. Another instance this multi-fit clip works is when someone has replaced one or more nail-heads that the clip fastens to and located them in the wrong place.Sold Individually. These clips attach to posts built in to the car. In case you're missing some...

Ford called this part a 'sleeve'. Attaches to the lower shifter arm with a hitch pin. Has nice bushing, with correct nut, washer, and pin. The 1967/68 and 1969/73 versions are identical. The C1AA-7353-C sleeve has fine threads, the C9OZ-7353-A has course threads. Fits all 1967-73 Mercury Cougar and Ford Mustang, and we suspect many other Ford vehicles beginning in 1961. Check out our video on rebuilding your shifter below: ...

C8OA-3B236-A Complete lower control arm cam and attaching bolt. 4 pieces included - Cam/bolt, lower cam, nut and lock washer. We offer this used front suspension lower control arm adjusting cam from rust free Western States cars. These are MUCH better quality than any of the stock "looking" reproductions offered. For use on all 1967 - 1973 Mercury Cougar and Ford Mustangs. Part of the C6OZ-3048-A lower arm mounting kit. Bolt/cam part number C8OA-3B236-A, secondary cam part...

This is a reproduction of the original white engine displacement decal with a blue background Powered by Ford (logo) followed by 351-2V Regular Fuel followed by white background with blue lettering, Once a Month, Crankcase Ventilation System, Cooling System Flush, and a Motorcraft, Autolite parts logo. Located on the top of the air cleaner. 13.50" span tip to tip.Fits the following models with a 351 2 barrel Regular Fuel engine: 1973 Cougar 1973 Mustang ...

Fits all V8s with oval air cleaner.

WOW! How long have we been trying to scrounge up good used pins for restoration? These are identical to what is found on all 1969 Cougar and Mustang Convertibles. They are correct for most of the 1970 model year and even if you are one of the few that own a late 1970 Mustang / Cougar they will work on your car too. These also work on the 1971-1973 Convertibles.The picture below shows the new reproduction on the bottom, used 69-70 in the middle and a 1971-1973 pin at top. //-->WCCC is...

Reproduction gold dichromate 10 blade alternator fan. Used on Mercury Cougars and Ford Mustangs manufactured after 11/17/1969. Actually this is a Ford part found on most all Ford automobiles from 1970-73. 10 blade alternator cooling fan. Replaces Ford Part #: DOAZ-10A310-B

Older used aluminum intake manifold. Port size is for the 2V cylinder heads. Perfect for adding a 4 barrel carburetor to a stock 351 Cleveland 2V engine.

New intake manifold that has never been used, but it's missing the packaging, so we're calling it an "out of box special". Port size is for the 2V cylinder heads. Perfect for adding a 4 barrel carburetor to a stock 351 Cleveland 2V engine.

Replaces Ford Part # C8AZ-2B164-A Sold individually

Transforms your interior into a concert hall with superior musical sound quality. Eliminates the need to crank up the volume on your sound system, and by reducing vibration, it minimizes distortion. Plus the reduced noise level makes for a more pleasant ride when the stereo is off. Flexible material won't crack or peel. Adhesive backing allows easy, permanent installation behind speakers in doors or back seat panels, under speakers in trunk...anywhere. The 36" x 60" material can be easily...

Reproduction disc brake hose bolt for any 1968-73 Mercury Cougar and generally all other Ford cars with factory disc brakes. Special hollow bolt with cross drilled hole. Attaches the high pressure hose to the caliper.