1973 Mercury Cougar

D3ZF-9600-AA Air cleaner base for all 1973 H code 351-2V engines. About 14.75 inches in diameter. Ford part number D3ZZ-9600-A.  Does not include snorkel.

Reproduction battery heatshield that fits many applications from 70-73, on most hi-performance engines. It was often the first part discarded but serves a real purpose.

Each of these great kits include all three required cables, including part numbers, proper terminal and post clamp ends. Starter cables are properly shielded from heat. The originals were either 43-55 Amp (Standard) Draw or 65-70 Amp (High) Draw. We recommend going with the High Draw. For 1972-73 Mercury Cougar and Ford Mustang all with V-8 engines.Positive cable is 10 1/4" center to centerNegative cable is 42" center to centerGround wire is 41" center to center Replaces Ford Part # :...

Each of these great kits include all three required cables, including part numbers, proper terminal and post clamp ends. Starter cables are properly shielded from heat. For all 1972-73 Mercury Cougar or Ford Mustang with 43-55 AMP alternators and V-8 engines. The originals were either 43-55 Amp (Standard) Draw or 65-70 Amp (High) Draw. We recommend going with the High Draw. As one customer put it, "These [standard draw cables] look anemic." (Thanks for the feedback Charles!) Replaces Ford Part...

No more crust, white powdery battery terminals. Just spray this stuff on, and after a few minutes....simply wash off with water! Not only can you use this stuff on your car, you can use it on your ATV's, quads, dirt bikes and even your ride on lawnmower! A handy item to have laying around your garage. Of course, there's a little more messy, mostly free alternative which you can find the ingredients for online, but why bother? This is a simple, fairly cheap product to have.  

This battery cover is designed to be used with any maintenance free flat top battery **24/60 series with original terminal location for the Autolite battery covers.

Everything you need to hold the battery down on your 71 -73 Cougar or Mustang. Included in this kit are the two stainless steel J-bolts, the hold down bracket and the hold down clamp.

Reproduction "Battery OK" Decal for the 1967 - 1982 Mercury Cougar / Ford Mustang

NOS service replacement battery tray, may not be exactly like the assembly line tray. Group 27 battery tray is typical for cars with air conditioning and higher amp alternators. Fits 1971-73 Mercury Cougar and Ford Mustang. Also 1970-71 Ford Torino and Mercury Cyclone and variants of the B or C midsize Ford and Mercury bodied cars.  Replaces Ford Part #: D0OZ-10732-B.

Exactly like the originals. This group 27 battery trays are a popular item for restorers since most of the originals have been destroyed by leaking batteries over the years. Fits 1971-73 Mercury Cougar and Ford Mustang. Also 1970-71 Ford Torino and Mercury Cyclone and variants of the B or C midsize Ford and Mercury bodied cars. Supplier misidentifies this part as D1ZZ-10732-B. Replaces Ford Part #: D0OZ-10732-B.

For those cold days in the garage, keep your head warm with our 100% acrylic knit 8" beanie. Classic black color with an embroidered WCCC walking cat logo on the front. Also works as a head collision absorber for those who own 1970 Cougars and work under the hood (you know what we mean). Great gift idea for Cougar fans, and for those who prefer beanies over baseball hats.

New axle bearing for any 8 or 9 inch Ford rear end with 28 splined axles. Common on all Mercury Cougar and Ford Mustang with V-8 engines. Excludes 31 splined axles as found on Boss and Cobra Jet cars.These should be professionally installed with a bearing press.

New front Inner wheel bearing with cup / race for original drum and disc brakes for all 1970-73 Mercury Cougar and 1970-73 Ford Mustang with V-8 engines. These are tapered bearings with cone or race. Inner diameter is 1.378 inches. These are dry bearings, meaning they will need to be packed with chassis bearing grease, prior to installation. A smaller outer bearing and this inner bearing are required for each side. Two of each needed for the front wheels. *Note - This bearing only fits the...

New front outer wheel bearing with cup / race for original drum and disc brakes for all 1970-73 Mercury Cougar and 1970-73 Ford Mustang with V-8 engines. These are tapered bearings with cone or race. Inner diameter is 0.865 inches. These are dry bearings, meaning they will need to be packed with chassis bearing grease, prior to installation. A large inner bearing and this outer bearing are required for each side. Two of each needed for the front wheels. *Note - This bearing only fits the...

Reproduction steering column bearing for the 67-73 Cougar or Mustang. The tilt columns take an upper and lower bearing, while the fixed column only takes an upper. Outside diameter: 1 1/2" Inside diameter: 1 1/4"*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Used lower steering column bearing for the 67-73 Cougar or Mustang. The tilt columns take an upper and lower bearing, while the fixed column only takes an upper. The upper bearing can be found here. Outside diameter: 1.500"Inside diameter: 1.060" *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

D2OZ-7976-A Aluminum bell housing, sometimes called a converter housing in the Ford shop manual. 1972 - 1973 Mercury Cougar and Ford Mustang with 351 engine and automatic FMX transmission, code X on your door data plate tag. Ford master part number D2OZ-7976-A.

Correct for 1971, 1972 and 1973 only. 351-2V and 351-4V engines , including Boss 351 for 1971 - 73. Ford part number D1TZ-6392-A and D1TZ-6392-C. Shipped bare, no hardware or clutch fork.

Eight piece kit that includes inner and outer belt-line for both door and quarter glass. This kit contains enough for both pieces of door and quarter glass. These strips run horizontally against your glass and keep water and debris from entering your rear quarter panels and doors causing them to rust out. These kits include the correct stainless steel trim on the interior side strips. Old belt-lines will become hard and trap grit causing your glass to get heavy vertical scratches. You can...

Eight piece kit that includes inner and outer belt-line for both door and quarter glass. This kit contains enough for both pieces of door and quarter glass. These strips run horizontally against your glass and keep water and debris from entering your rear quarter panels and doors causing them to rust out. These kits include the correct stainless steel trim on the interior side strips. Old belt-lines will become hard and trap grit causing your glass to get heavy vertical scratches. You can...

Eight piece kit that includes inner and outer belt-line for both door and quarter glass. This kit contains enough for both pieces of door and quarter glass. These strips run horizontally against your glass and keep water and debris from entering your rear quarter panels and doors causing them to rust out. These kits include the correct stainless steel trim on the interior side strips. Old belt-lines will become hard and trap grit causing your glass to get heavy vertical scratches. You can...

Eight piece kit that includes inner and outer belt-line for both door and quarter glass. This kit contains enough for both pieces of door and quarter glass. These strips run horizontally against your glass and keep water and debris from entering your rear quarter panels and doors causing them to rust out. These kits include the correct stainless steel trim on the interior side strips. Old belt-lines will become hard and trap grit causing your glass to get heavy vertical scratches. You can...

Used cigar or cigarette lighter bezel for 1971-73 Mercury Cougar and Ford Mustang. Ford part # D1ZZ-15052-A and D1ZB-15053-A

Lower dash bezel to the left of the steering column. This one is for those 1971-73 Mercury Cougars with factor air conditioning. Cars with only the heater option used a different bezel that has a hole for the vent cable. This bezel is blank, and only has the rectangular hole for the air conditioning vent register.Replaces Ford part number D1WB-65044A13-BC (cast on the part) or D1WY-6504393-B

Lower dash bezel to the left of the steering column. This one is for those 1971-73 Mercury Cougars without factor air conditioning. Cars with only the heater option had dual fresh air vents. This bezel is for the driver side fresh air vent register and control cable, it has a molded hole for the vent cable.Replaces Ford part number D1WB-65044A13-AC (cast on the part) or D1WY-6504393-A.

Chromed plastic driver side fresh air "Vent" bezel. Mounts with the cable through a hole in the dash panel, just to the right of the vent register. Most all of these used bezels have a defect in the chrome plating along the bottom, not visible when installed.Replaces Ford part D1WA-18A405 (casting in the part), or D1WY-10852-B.*Note - Does not fit Mustang

This trim ring that surrounds the glove box release button is often missing. Easily installs by snapping in place. Better fit than the reproductions out there.Replaces Ford part number C6OB-62060A12.

Best used bezel we can find from a Western parts car. "Almost" pit free. If you look close you will see some tiny specs. Click onto the image to enlarge the picture.Replaces Ford part number D3WB-13064, and D3WY-13064-B.

Restored driver (left hand) side headlight bezel moulding for any 1973 Mercury Cougar. Chromed only, detail black painted portions not completed. We also have grade A and B used mouldings. Refundable core charge additional.Like all of our rechromed parts, if you have exceptionally clean cores and have high standards you will want to send your cores in advance. When you do we will do what we call "core matching". If you send in parts with ZERO pits you will get back restored parts that had...

Best used bezel we can find from a Western parts car. "Almost" pit free. If you look close you will see some tiny specs. Click onto the image to enlarge the picture.Replaces Ford part number D3WB-13052 and D3WY-13064-A.

Restored passenger (right hand) side headlight bezel moulding for any 1973 Mercury Cougar.  Chromed only, detail black painted portions not completed. We also have grade A and B used mouldings. Refundable core charge additional.Like all of our rechromed parts, if you have exceptionally clean cores and have high standards you will want to send your cores in advance. When you do we will do what we call "core matching". If you send in parts with ZERO pits you will get back restored...

These B grade headlight doors will have some pitting in the chrome. Some of them will be nearly pit free, but may have a small crack. Click onto the image to enlarge the picture.Replaces Ford part number D3WB-13064, and D3WY-13064-B.

These B grade headlight doors will have some pitting in the chrome. Some of them will be nearly pit free, but may have a small crack. Click onto the image to enlarge the picture.Replaces Ford part number D3WB-13052 and D3WY-13064-A.

Reproduction headlight switch bezel for any 1971-73 Mercury Cougar and Ford Mustang.  Replaces Ford part number D1ZB-11649-AC.

Used headlight switch bezel for any 1971-73 Mercury Cougar and Ford Mustang. Good used bezel with shiny chrome. May have one small nick in the chrome or one broken plastic stud on the reverse.Replaces Ford part number D1ZB-11649-AC.

No cracks or deterioration from UV rays.

License to rear bumper spacer used on all 1973 Cougars. Usually this item is badly cracked or missing. This is a show quality used part for those that are concerned about less than obvious detail items.NOTE: The difference between the 71-72 version and this 73 version is that the 73 did not have a casting number and the earlier year versions did.

Used grade A power window switch bezel for the Mercury Cougar. This bezel is used with all power window switches, except for the driver side door, and was only used on the 1973 model. Ford engineering # D3MB-14528-DA.

Used grade B power window switch bezel for the Mercury Cougar. This bezel is used with all the power window switches, except for the driver side door, and was used on the 1973 model only. B grade, expect rust pitting in the chrome. Ford engineering # D3MB-14528-DA.

The Cougar radio bezel at first glance looks much like the Mustang radio bezel. It does in fact carry a Cougar part number and has a slightly different shape to it. The most noticeable difference is the fifth screw hole at the top middle, Mustang does not have this hole. Keep in mind the AM-8 track used the same bezel but with an enlarged hole.This enlargement was done at the factory prior to plating and if you look at the back side you will see the cut line. This is a pit free bezel that has...

The Cougar radio bezel at first glance looks much like the Mustang radio bezel. It does in fact carry a Cougar part number and has a slightly different shape to it. The most noticeable difference is the fifth screw hole at the top middle, Mustang does not have this hole. Keep in mind the AM-8 track used the same bezel but with an enlarged hole.This enlargement was done at the factory prior to plating and if you look at the back side you will see the cut line. This is a B grade bezel that has...

Replace that old, pitted, and cut up radio bezel with this quality concours part. This is a Mustang piece that will work on your Cougar but is slightly different. The easiest way to identify a Mustang bezel from a Cougar bezel is that Mustang had four mounting holes and Cougar had five. Will need slight modification to fit Cougar. Replaces Ford Part #: D1ZZ-18842-A.

Used driver side (left hand) rear marker light bezel for any 1971-73 Mercury Cougar. Originally painted body color, flush mounted to the passenger side rear quarter panel. Has two attaching studs, and sometimes one locating stud. We often times find that the locating stud is broken or cut off. You will want to cut the corner stud off if using the available reproduction Mustang red rear reflectors. All of our bezels will have the 2 larger studs intact. See related items for new lenses and...

Used passenger side (right hand) rear marker light bezel for any 1971-73 Mercury Cougar. Originally painted body color, flush mounted to the passenger side rear quarter panel. Has two attaching studs, and sometimes one locating stud. We often times find that the locating stud is broken or cut off. You will want to cut the corner stud off if using the available reproduction Mustang red rear reflectors. All of our bezels will have the 2 larger studs intact. See related items for new lenses and...

Good used part with no peeling foil covering or cracks. Of the three studs on the back you can rest assured one if not two of the studs will have cracks or a portion missing. We also have these in grade "B" for $43.85. Contact us for the many options as we have over 50 in stock. We sell the metal woodgrain painted center section separate. ...

Good used part with a little peeling on the foil and this part will most likely have cracks. Of the three studs on the back you can rest assured one if not two of the studs will have cracks or a portion missing. Contact us for the many options as we have over 50 in stock. We sell the metal woodgrain painted center section separate.

Restored driver side (left hand) 1973 Mercury Cougar taillight bezel. These have been restored with the correct bright dipped, anodize finish. You will have to do the finish, detail painting. Note that in the buffing process the ridges are worn down noticeably on the horizontal bars. Mercury part number D3WY-13489-B. This is a trim restoration service, if you do not have an acceptable core trim piece, please purchase a used or core D3WY-13489-B trim. Call 503-463-1130 if you have any...

Used driver side 1973 Mercury Cougar tail light bezel. Minor blemishes, perfect driver quality. Mercury part number D3WY-13489-B. No Core required. Thinking about adding some LED taillight bulbs to your car? Here is great little video that shows the performance of LEDs and traditional bulbs side by side so that you can make an informed decision. ...