1973 Mercury Cougar

Grade "B" part that will have only one of the four mounting tabs broken or cracked. Select a color and we will attempt to accommodate you.

This is the manual steering gear box for 1971 Mercury Cougars. Marked SMA-R and is 22:1 ratio. It is pretty rare to find a Cougar optioned without power steering. According to Kevin Marti's COUGAR...by the Numbers book 99% of all 1971 - 1973 Cougars came with power steering from the factory. If you have a non-power steering Cougar for these years you are in the 1% club.  1972-73 manual Steering boxes had a ratio of 24:1, and were tagged SMA-R.  We offer used boxes because...

This is the manual steering gear box for 1972 1973 Mercury Cougars. Marked SMA-T and is 24:1 ratio. It is pretty rare to find a Cougar optioned without power steering. According to Kevin Marti's COUGAR...by the Numbers book 99% of all 1971 - 1973 Cougars came with power steering from the factory. If you have a non-power steering Cougar for these years you are in the 1% club. The current used steering box has a date of 1H06B, August 6, 1971. For an early 1972 Cougar or Mustang. Used...

Used lower steering column knuckle for the Mercury Cougar or Ford Mustang. This unit is used in the 1970-73 tilt only column and can be the issue when you have a sloppy feeling tilt column. The hard steel pin will often waller out the soft cast metal and cause play in the column. Ford part # D1AZ-3D651-A, casting number D1AA-3D651-AA or D0AA-3508-F. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent...

Used upper steering column knuckle for the Mercury Cougar or Ford Mustang. This unit is used in the 1970-73 tilt only column. Ford casting # D1AZ-3511-AWA.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

This is the closed cell foam cover for your power steering lines to keep them from getting scuffed, and they repel oil quite well too. These are always disintegrating on the older cars and need replacement after 40 years of service. this line length can be cut to fit easily on a split line like the Cougar. Good for Cougar, Comet, Mustang, Montego, Torino, Cylone, Maverick and Ranchero.Measures 21" long

This is the brass piece that connects the keylock to the ignition switch.

Reproduction Black Steel / Black Leather steering wheel for your 68 - 73 Mercury Cougar. This kit includes: Steering wheel, hub, horn button and center decal. Hardware included.

Reproduction Chrome / Black Leather 4 spoke steering wheel for your 68 - 73 Mercury Cougar. This kit includes: Steering wheel, hub, horn button and center decal. Hardware included.

Reproduction Chrome / Black Leather steering wheel for your 68 - 73 Mercury Cougar. This kit includes: Steering wheel, hub, horn button and center decal. Hardware included.

Reproduction thick grip Mahogany Woodgrain / Chrome steering wheel for your 68 - 73 Mercury Cougar. This kit includes: Steering wheel, hub, horn button and center decal. Hardware included.

Reproduction Chrome / Dark Mahogany Woodgrain steering wheel for your 68 - 73 Mercury Cougar. This kit includes: Steering wheel, hub, horn button and center decal. Hardware included.

Reproduction OE spec reproduction of the two spoke steering wheel. This is the exact size and feel as the original, and has the correct factory detail Having issues with wobbly or loose steering? Check out our video on sloppy steering below. ...

Reproduction OE spec reproduction of the three spoke woodgrain deluxe rimblow steering wheel. This is the exact size and feel as the original, and has the correct factory detail on the spokes and center hub. Included are the wheel, gap cover and installed rimblow switch. Having issues with wobbly or loose steering? Check out our video on sloppy steering below. ...

This reproduction steering wheel is a replica of the wood rimmed steering wheel originally equipped on 1967 Shelby GT350's and GT500's. It has a beautifully finished real solid wood rim with proper finger indents and a distinctive black band around the back surface just like the originals. The 3 spoke design is brushed stainless steel with 4 chamfered holes per spoke, and unique black rubber finger guards. The main hub is CNC machined aluminum with a satin finish. Each wheel is equipped with...

Good used pad that will most likely need to be repainted unless it is black. Not hard and crispy looking. Comes naked as shown.

Decent offshore reproduction but nothing beats the fit and finish of a good original FoMoCo part. Checkout our used as we have multiple colors in stock. This repro pad only comes in black. Replaces Ford part number D0AZ-3623-A.

Good used pad available in limited colors, call for current stock on hand. We often have black and green available but hit and miss on the other colors. The center emblem is sold separate. Engineering number as seen from the backside reads D0AA-3E662-BW, Ford part number D0AZ-3623-A

This is the steel center section only. Very hard to find with no damage but we have a few! No rust other than surface, no obvious filler and no dents. Grade "A" Western sheet metal is always going to be your best bet when you can find it.This unit is also known as a bumper filler, rock guard, or filler panel.Ford part # D3WY-17779-D.

Rubberized bumper filler combination stone deflector, that mounts on the passenger side fender on a 1973 Cougar. This unit is also known as a bumper filler, rock guard, or filler panel. Grade A used condition, may have a defect that can't be seen when installed.Replaces Ford part number D3WY-17779-A.

Black plastic filler that attaches to the rear of the stone guard. Fills in the portion between the stone guard and headlights. 1973 driver side only.

Black plastic filler that attaches to the rear of the stone guard. Fills in the portion between the stone guard and headlights. 1973 passenger side only.

Used quarter window lower window guide stop. Made of black plastic, held on by a single bolt. Mounts to the window guide on any 1971-73 Mercury Cougar or Ford Mustang Coupe or convertible. One per side, sold individually.Replaces part # D1ZZ-6539805-A.

Quarter window upper stop bracket, fits all 1971-73 Mercury Cougar and 1971-73 Ford Mustang coupe or convertible models. This is the smaller of the two stop brackets, and it installs towards the back of the window. There is a decent illustration of the quarter window installation in the Osborn Body Assembly Manual. One stop bracket per side, right and left are the same.Ford part number D1ZB-6529968-A.

Quarter window lower stop bracket, fits all 1971-73 Mercury Cougar and 1971-73 Ford Mustang coupe or convertible models. This is the longer of the two stop brackets, and it installs near the B pillar of the window. There is a decent illustration of the quarter window installation in the Osborn Body Assembly Manual. One stop bracket per side, right and left are the same.Ford part number D1ZB-6530600-A.

These are the straps that hold the gas tank in place. 2 required, sold individually.Replaces Ford part number D1ZZ-9092.

Universal wire loom plastic clip for any application on Cougars or Mustangs, as well as many other models.5" x .26"

These are the straps that hold the gas tank in place. Sold as a pair.Replaces Ford part number D1ZZ-9092.

New strip caulk for the Mercury Cougar or Ford Mustang. These units come in one foot strips and are used for sealing the front fenders to top of aprons and for sealing the fuel tank flange to the trunk floor. They are also used for sealing the floor drain plugs, gas filler necks, door panel water shields, plus many other components that are fastened to the body. This box contains 60 individual strips of black non-hardening caulk.

Nice used driver side strut rod that fits all 1970-73 Mercury Cougar and Ford Mustangs. Our good used Western strut rods are the best you will find. No bends, nor damaged threads, not heavily rusted and correct for your Mustang / Cougar and 1970-71 Torino, Cyclone, Ranchero.. Functionally the same as 1968-69 strut rods, just not stepped down threads at the end. Ford part number C9ZZ-3468-C. Sold as a bare strut rod, we also offer the used hardware for installation here. ...

Nice used passenger side strut rod that fits all 1970-73 Mercury Cougar and Ford Mustangs. Our good used Western strut rods are the best you will find. No bends, nor damaged threads, not heavily rusted and correct for your Mustang / Cougar and 1970-71 Torino, Cyclone, Ranchero.. Functionally the same as 1968-69 strut rods, just not stepped down threads at the end. Ford part number C9ZZ-3468-D. Sold as a bare strut rod, we also offer the used hardware for installation here. ...

 ‹— 1967 Stock alignment verses reproduction alignment. (Thanks for the pic Peter!)   A nice reproduction. Painted black. Ready to install. Includes correct castle nut. Required to install reproduction front end rebuild kit on a 1967. Replaces Ford Part # C9ZZ-3468-D. We highly encourage you to consider our used rods over these Chinese parts. Our grade "B" rods will take some effort to make look new but in the end it is worth it. The Chinese strut rods are different (but...

A nice reproduction. Painted black. Ready to install. Includes correct castle nut. Includes both the left hand and right hand strut rod arm. These are required to install the reproduction front end rebuild kit on a 1967. Replaces Ford Part #: C9ZZ-3468-C & C9ZZ-3468-D. We highly encourage you to consider our used rods over these Chinese parts. Our grade "B" rods will take some effort to make look new but in the end it is worth it. The Chinese strut rods are different (but similar) from one end...

 ‹— 1967 Stock alignment verses reproduction alignment. (Thanks for the pic Peter!)   A nice reproduction. Painted black. Ready to install. Includes correct castle nut. Required to install reproduction front end rebuild kit on a 1967. Replaces Ford Part #: C9ZZ-3468-C. We highly encourage you to consider our used rods over these Chinese parts. Our grade "B" rods will take some effort to make look new but in the end it is worth it. The Chinese strut rods are different (but...

Nuts and bolts, associated with the installation of our used 1970-73 strut rods.

This nut fits onto the strut brace at the front of the car, and not the control arm end. It is the lock nut that goes on after the the bigger strut rod bushing nut.Replaces Ford part # 340460-S

This nut fits onto the strut brace at the front of the car, and not the control arm end.Replaces Ford part # 380517-S

This listing is for a premium quality pair of 1970 original strut rods in grade "A" used condition. What sets them apart from our grade "B" rods is that after they have been bead blasted they have a smooth finish, no pock marks from rust. This is for the person who is doing a show car and wants the very best, original correct parts that can be found. The reproductions are made in China and work fine but they are different on every detail and do not come with the specialty bolts that attach the...

Reproduction 8-32 x 1/2" stud used to attach the convertible boot mouldings on any 69-73 Cougar or 65-73 Mustang. A number of these studs were installed on the mouldings, going through the body of the car and attached underneath the sheet metal using the boot nuts.

Used 14x7" styled steel wheel for your Mercury Cougar. This painted Kelsey Hayes wheel used with small cap and brushed finish trim ring that are sold separate. Cap and lugs are sold separately. Total width is 8" with a backspacing of 4".Ford part # D0ZZ-1007-C.

Excellent quality reproduction sun visor assembly for the convertible 1971-73 Mercury Cougar and Ford Mustang. These feature the correct satin finish, fit perfect and look spot on. The original casting numbers as seen on the back side will read D1ZB-7604123-AE for the driver side and D1ZB-7604122-AE for the passenger side. Sold as a pair.Replaces Ford part numbers D1ZZ-7604144-A, D1ZZ-7604145-A, and D2ZZ-7604144-A, D2ZZ-7604145-A.

Pair of reproduction brackets and rods for the sun visors in the Mercury Cougar or Ford Mustang. *NOTE* These units will also work for the 1971-73 Ford Mustang fastback (sport roof).

Grade B used convertible sun visor bracket assembly for the driver side of any 1971-73 Mercury Cougar or Ford Mustang. Grade B will have some pitting in the pot metal. Sanding and painting will be required for the best results. Two casting numbers found between 1971 and 1973. We won't always have both numbers in stock but from the front side they are the same. Can be either D1ZB-7604123-AE or D2ZB-7604123-AA.  These will almost always, show some wear in the pocket, where the hook...

Grade B used convertible sun visor bracket assembly for the passenger side of any 1971-73 Mercury Cougar or Ford Mustang. Grade B will have some pitting in the pot metal. Sanding and painting will be required for the best results. Two casting numbers found between 1971 and 1973. We won't always have both numbers in stock but from the front side they are the same. Can be either D1ZB-7604122-AD or D2ZB-7604122-AA.  These will almost always show some wear, in the pocket where the hook...

Used 2 hole front mount center bracket for the sun visors for the Mercury Cougar and Ford Mustang convertibles.  Contrary to what the aftermarket says, these are slightly different from the 1968 'C8ZB-6504132' sun visor bracket. These colors don't always match the seat color, so plan on spraying these with vinyl paint to match your interior. We often times can supply your desired color, mention your color in the 'comments section' of your order. We have these in a limited supply. Ford...

This is the 1968 coupe version of the 2 hole front mounting sun visor center bracket and is a close match for the 1968 / 1969 / 1970 convertible sun visor bracket.  This bracket is not, however, an exact match for 1971 /1972 / 1973 convertible as some sites suggest, but it will work. On the 71 - 73, the hole spacing and distance from the windshield are identical to this bracket, but the bracket is not the same size. This bracket is 1/8" longer on the...

Reproduction 2 screw rear mount sun visor bracket is only available in black, so plan on painting this unit to match. We have most other unfaded colors in used. Replaces Ford Part #: D1AZ-6504132-A or D3AZ-6504132-A.

Used 2 screw rear mount sun visor bracket for the Mercury Cougar or Ford Mustang coupe. The MPC lists other part numbers such as D1ZZ-6504132, D2ZZ-6504132, and D3AZ-6504132, which are specific to some colors, but we have yet to seen them in a car. The colors don't always match the seat color, so plan on spraying these with vinyl paint to match your interior. We often times can supply your desired color, so mention it in the 'comments' section of your order. Ford part # D1AZ-6504132,...