Your cart is empty!
Our shopping cart requires the use of cookies. If you have your cookies disabled, please enable them for our site to place an order. If you have cookies enabled and have added an item to your cart, but you are still seeing this message, that could indicate that the cookie for our shopping cart is corrupted on your computer.You should be able to fix this by either:
Buy Details
Contains nut and washer. Fits all Ford alternators. AMK F-644.
AMK engine fastener kit for 1971 Mercury Cougar and Ford Mustang with J or C code 429 Cobra Jet engines. This kit claims to have 136 pieces. This kit additionally fits 1970-71 Ford Torino and Mercury Cyclone and other variants with 429CJ engine.Kit typically includes: fasteners to attach air cleaner, carburetor, crank pulley, distributor / points / condenser / vacuum advance, drain plugs, engine tag, exhaust manifolds, fan / fan clutch, fuel pump, shroud, ignition coil and strap, intake...
Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds.
Reproduction Firewall Insulation Pad Clip Kit for the 1967 - 1973 Mercury Cougar / Ford Mustang
This is a Mustang kit and it includes 4 screws, 2 metal nuts, 2 self-threading plastic nuts and 2 anti-rattle bumpers as pictured.For Cougar, you need this kit plus 2 more plastic nuts, found here.
Used bolts, and usually new washers. Coupe kit comes with 4 - "A" bolts, 4 "B" bolts, and 2 "D" bolts, 12 new washers. Kit fits all 1970-73 Mercury Cougar and Ford Mustang coupes. Coupes or hard tops will have shoulder belt hardware. We will make sure these original seat belt bolts are damage free and rust free. The gold finish will be degraded. There were minor and major changes almost every year. We also have hundreds of used belts and belt sets that we cannot possibly list...
Used bolts, and usually new washers. Convertible kit comes with 4 - "A" bolts, 4 "B" bolts, 10 new washers. Kit fits all 1970-73 Mercury Cougar and Ford Mustang convertibles. Coupes or hard tops would include shoulder belt hardware. We will make sure these original seat belt bolts are damage free and rust free. The gold finish will be degraded. There were minor and major changes almost every year. We also have hundreds of used belts and belt sets that we cannot possibly list all of, so give us...
AMK strut rod hardware kit, course threaded bolts and nuts with cotter pins as shown.
Used upper rear fender brace that brace is visible when you open the door and look in the upper part of the fender void. Welds to the cowl on 1971-73 Mercury Cougar and Ford Mustang. Same tab either side. Ford part number D1ZZ-16A006-A.
Filter / screen for the C6 transmissions, for all 1967-73 and 1967-73 Mercury and Ford.
Replacement filter for FMX transmissions. Fits all Ford FMX transmissions for any 1969-73 Mercury Cougar or Ford Mustang with that X code FMX transmission.
Replaceable filter which attaches to original fuel sending unit. Fits 3/8" tube. Replaces Ford part #: D1AZ-9A011-A.
Replacement transmission pan filter and pan gasket kit. For the C-6 (U Code) transmission. Replaces Ford Part Number: C7ZZ-7A098
Replacement transmission pan filter and pan gasket kit. For the FMX (X Code) transmission. Replaces Ford Part Number: C9ZZ-7A098
NOS air cleaner breather element filters for all 1970-73 Mercury Cougar and most all Fords with V-8 engines. This filter fits inside your air cleaner base, a hose connects to the fitting and goes to the PCV valve in the valve cover. Sold as shown, cartridge holder not included.Packaging may vary
Finally, a reproduction firewall for your Mercury Cougar or Ford Mustang convertible. Ford part # D1ZZ-6501610-A.
Rubber plugs for sealing the holes in the firewall of any 1967-68 Mercury Cougar or Ford Mustang. These plug the firewall holes if you don't have air conditioning or if you have deleted your heater core. Fits 1" body panel holes for all years.Sold as a pair.Original Ford part 377678-S2
Reproduction thin firewall insulation pad with clips for the Mercury Cougar or Ford Mustang. This unit will fit both the A/C and non A/C Cougar or Mustang.
Sold in a set of three, includes attaching screws. Replaces part # 380478-S3
Reproduction firewall to hood seal or cowl seal for the Mercury Cougar or Ford Mustang. Comes with attaching clips. Replaces Ford part # D1ZZ-16740.Customer feedback from mercurycougar.net: Don and WCCC were always one of the service quality benchmarks for my business. Despite the many pressures faced by any small business owner, Don always treated me and my car as if we were his only customer. And, he NEVER let me down - parts always as advertised, and delivered timely.That impressed me then,...
Replaces Ford Part # : D1ZZ-3513-A. For use only with 3 and 4 speed manual transmission cars.
Seal the steering column flange to the firewall. Used on cars with automatic transmission. Replaces Ford part # D1ZZ-3513
All steel fitting for the lower radiator tank, found on all cars with automatic transmissions. The fine threads go to the radiator and the transmission cooling line screws onto the flared fitting after installation into the radiator. Two needed per car, sold individually. Fits all years 1967-73, and all automatic transmissions. 1/2" threads go to cooling lines. 3/8" threads go into the radiator. *Note - This is an original steel fitting, not a brass reproduction. ...
Used convertible top flapper stopper. Technically called a "lasting", this is the thin strip of 1/16" thick metal that slides inside the sleeve of your convertible top to keep it from flapping. We will rarely have these on hand, so we've included the dimensions so that you can fabricate your own if needed. 2 required per vehicle.
This flat nut has many uses, most commonly used on the 67 - 68 corral / walking cat headlight eyelid door assembly or the 69 - 70 quarter script. Can be used on anything that has a 3/32" stud. Can be used for many items on a variety of vehicles including the Mustang, Torino, Cyclone etc.Sold individually.
New flat nut, these attach both the shifter seal and shifter dial to the under side of the automatic shifter bezel. Check out our video on rebuilding your shifter below: ...
Good used OEM flex plate for all 69 - 73 Mercury Cougar and Ford Mustang with 302 / 351W engines, and C4 or FMX transmissions. Not for use on a 1968 with 302. The starter ring will show wear and some will choose to replace, others have removed the starter ring and just turned it around so the unused portion of the ring will now contact the starter drive gear. ...
Brand new flex plate for all 1970-71 Mercury and Ford with 429CJ engines, and C6 transmissions. Comes complete with new starter ring gear installed as shown.
Reproduction flexible duct end that was originally stapled to the passenger side fresh air duct, found behind the passenger side dash panel of all 1971-73 Mercury Cougar and Ford Mustangs without air conditioning. Restoration tip - Ford used a ring of foam as a seal between the duct and fresh air vent. Replaces Ford part number D1ZA-18C305-AB.
These quality mats are made in the USA by Auto Custom Carpets. They are a good fit with an aggressive grip rubber backing. These are heavy mats that will not easily slip out of place or become "wadded up" under your brake pedal. They will hold their form for many years and do more than just enhance the look of your Cougar, they will provide an extra layer of insulation providing an added barrier for heat and sound. Very nice carpet floor mats that make for an ideal gift for that Cougar lover...
New fluorescent needle restoration paint for the gauges in your Mercury Cougar or Ford Mustang. Over the years, the sun has wreaked havoc on your Cat or Pony. This sun damage has also had it's way with the needles on you gauges and washed them out. This true fluorescent paint will not only make your needles look factory fresh, but will also bring back their glow at night. One jar contains 2.25ml worth of paint.
This is a much cheaper version of the foil sound deadeners and underlays we sell. This particular insulation is basically bubble wrap with two layers of foil on both sides. Good for insulating headliners, floor pans, trunk areas, door panels, kick panels and just about anything else you might want to use it for. This insulation comes in a 48" X 72" roll. Just grab a pair of scissors and cut your shapes. You can use any adhesive you like (contact cement or weatherstrip adhesive,...
This USB flash drive contains the electronic collection of the 64 - 71 Ford Car and Truck Technical Service Bulletins (TSB) released from October 19th 1964 through September 10th 1971. Technical service bulletins are official communications between Ford and their dealerships that describe processes for troubleshooting or fixing certain common problems. TSB's document recommended procedures for repairing vehicles, when there are several occurrences of an unanticipated problem. TSB's can range...
Reproduction driver side (left hand) inner front frame patch for Mercury Cougar and Ford Mustang.
Reproduction passenger side (right hand) inner front frame patch for Mercury Cougar and Ford Mustang.
Reproduction driver side (left hand) outer front frame rail patch for Mercury Cougar and Ford Mustang. The outer rail has weld nuts installed for proper installation.
Brass and steel freeze plug or expansion plug set for any Ford 351C engine. 1970-74 Mercury Cougar and 1970-73 Ford Mustang. 12 piece set with threaded screw in plugs as shown.
Brass and steel freeze plug or expansion plug set for any Ford 429 / 460 / 429CJ engine. 1971 Mercury Cougar and 1971 Ford Mustang. 13 piece set with threaded screw in plugs as shown.
Steel freeze plug or expansion plug set for any Ford 429 / 460 / 429CJ engine. 1971 Mercury Cougar and 1971 Ford Mustang. 13 piece set with threaded screw in plugs as shown.
Brass and steel freeze plug or expansion plug set for any Ford 289 / 302 / 351W engine. 1967-70 Mercury Cougar and 1967-73 Ford Mustang. 15 piece set with threaded screw in plugs as shown.
Good quality reproduction front cross member for your 71 - 73 Cougar or Mustang. This is the frame / body piece that goes underneath your core support and receives the front ends of the strut rods. Sold as a stand alone part and does not come with strut rods or any strut rod hardware.Width: 34.75"Diagonal from outer bottom corner to outer top edge: 5"
Reproduction driver side (left hand) front inner apron for Mercury Cougar and Ford Mustang.
Reproduction passenger side (right hand) front inner apron for Mercury Cougar and Ford Mustang.
This is the very best we can offer. No cracks in the plastic holster, good color and no fraying on the webbing. NOTE: Front retractors are not side specific for all years 67-73, and are good for Cougar AND Mustang applications.Also, the difference between the standard and deluxe versions are the end of the buckle, the standard is rounded and the deluxe is ridged. Check out our video "All about seat belts" below. ...
This is a fully functional grade "B" retractor that will have a small crack in the plastic "holster" and may show very slight pitting on chrome. Driver quality, ready to plug and play. NOTE: Front retractors are same for left and right, and are good for all 67-73 Cougar AND Mustang applications. Also, the difference between the standard and deluxe versions are the end of the buckle, the standard is rounded and the deluxe is ridged. Check out our video "All about seat belts" below. ...