Contact Us / Visit Us (click here)
If the Shopping Cart takes too long to respond, you can bypass the shopping cart and go straight to the checkout page by clicking the following link: Checkout.
International Customers Click Here [Updated 1/2024]
Loading Trivia . . .

Search This Category:
Select layout:
Products (Click sub-categories above to ONLY display results for that Sub-Category) 1489-1536 of 2535
Price: $4.85

Buy Details

Availability: In-Stock Item
Item #: 41280 -

Stainless screw, most correct looking we have found. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding, two per center grille moulding and five per hood lip moulding for a total of 50 screws. In 1969 - 1973 they were used on the wheel lips mouldings. The 1971 - 1973 hood lip mouldings used the same screw but it was 5/8" tall. SOLD AS A SET OF 10.Fits:1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar1971 Mercury Cougar1972...

Price: $5.36

Buy Details

Availability: In-Stock Item
Item #: 41154 -

Not 100% correct, but close and functional. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding, two per center grille moulding and five per hood lip moulding for a total of 50 screws. In 1969 - 1973 they were used on the wheel lips mouldings. The 1971 - 1973 hood lip mouldings used the same screw but it was 5/8" tall. Sold as a box of 100.

Price: $0.85

Buy Details

Availability: In-Stock Item
Item #: 32158 -

8-32 x 1 inch long screws for attaching automatic shift bezels on 1969-73 Mercury Cougar or Ford Mustang with added Mass Backed Carpeting. Shiny zinc screws as shown, set of 4. Replaces Ford Part #: 381571-S

Price: $17.35

Buy Details

Availability: In-Stock Item
Item #: 26682 -

Replaces Ford part # D1ZZ-9072. Special gas proof rubber seal that mounts in gas tank and filler pipe. Warning! If reproduction tank or filler pipe is not the same dimensions as originals the seal may leak, make sure and check for a good seal before putting into use.

Price: $15.73

Buy Details

Availability: In-Stock Item
Item #: 10035 -

Oil seal for rear axle on any 1967-73 Mercury Cougar or Most Ford cars with 28 spline axles. Most all Cougar and Mustang received 28 splined axles, whether they have an 8 inch or nine inch rear end from the factory. Seal measurements: 1-3/8 inch inside diameter, 2-17/64 inch outside diameter. Two needed per axle, sold individually. We stock Timken brand of seals.Replaces Ford part number C7OZ-1177-B.

Price: $6.69

Buy Details

Availability: In-Stock Item
Item #: 10042 -

Oil seal for rear axle on any 1968-73 Mercury Cougar or Most Ford cars with 31 spline axles. Typically only 428CJ, 427-4V, and Boss 302's got the heavy duty 31 splined axles from the factory, most Cougar and Mustangs have 28 splined axles. Seal measurements: 1-1/2 inch inside diameter, 2-17/64 inch outside diameter. Two needed per axle, sold individually. We stock Timken brand of seals.Replaces Ford part number C7OZ-1177-A.

Price: $45.55

Buy Details

Availability: In-Stock Item
Item #: 27603 -

Quality kit for rebuilding your disc brake distribution block combination proportioning valve on 1970-73 Mercury Cougar and Ford Mustangs. Special molded and round O-rings are made from EPDM (Ethylene Propylene 70 Durometer) which is designed SPECIFICALLY to withstand chemical degradation caused by prolonged exposure to brake fluid. We custom made the spring from the exotic alloy INCONEL, which will never rust and will retain its factory specification compression strength many times longer...

Price: $11.85

Buy Details

Availability: In-Stock Item
Item #: 25866 -

When it's time to replace your old decaying foam seal, go with our reproduction weatherstrip retainer foam roll with peel off adhesive. Goes between the roof and door / window channel.  These are not technically manufactured to fit the Cougar / Mustang, however these are very close to the originals and come from the manufacturer in a roll that is 4' X 1" X 1/8".  One roll is more than enough to do one side, but you will need 2 rolls to do both sides. ...

Price: $5.27

Buy Details

Availability: In-Stock Item
Item #: 14248 -

We suggest using white lithium grease or petroleum jelly to ensure the seal will not stick to the shift lever. Fits 1969-73 Mercury Cougar and Ford Mustang, additionally it also fits 1971+ Maverick and Comet with floor shift automatic only.  If you have any side-to-side play in the shifter, this seal will not last. We do have the shifter bushings available. Replaces Ford part  numbers C9ZZ-7D351-A & D1ZZ-7D351-A. Get the matching mounting clips here. Check...

Price: $15.85

Buy Details

Availability: In-Stock Item
Item #: 33381 -

Top Loader transmission input shaft seal, small shaft, 289, 302, 351, and 390 only. Quality Timken part. Fits all 3 and 4 speed Top Loader Ford transmissions 1967-73 Mercury Cougar and 1965-73 Ford Mustang. Follow manufacturers instructions for installation or go to YouTube University.*Note - excludes big shaft 428CJ, 429CJ, and Boss 429 transmissions.

Price: $15.85

Buy Details

Availability: In-Stock Item
Item #: 33379 -

Top Loader transmission rear seal, 28 splined shaft, 289, 302, 351, and 390 only. Quality Timken part. Fits all 3 and 4 speed Top Loader Ford transmissions 1967-73 Mercury Cougar and 1965-73 Ford Mustang. Follow manufacturers instructions for installation or go to YouTube University. *Note - excludes big shaft 428CJ, 429CJ, and Boss 429 transmissions.

Price: $15.85

Buy Details

Availability: In-Stock Item
Item #: 33380 -

Top Loader transmission rear seal, big shaft 31 splines, 428CJ, 429CJ, and Boss 429 only. Quality Timken part. Fits 4 speed Top Loader Ford transmissions 1968-71 Mercury Cougar and 1968-71 Ford Mustang. Follow manufacturers instructions for installation or go to YouTube University.

Price: $2.75

Buy Details

Availability: In-Stock Item
Item #: 10907 -

Premium reproduction rubber seal with the proper thickness of the 1967-68 seal as found on Mercury Cougar and Ford Mustang except these are not molded to the extension contours. Starting in 1969 this channel seal was manufactured slightly smaller which tightened up the gap on the fender and quarter extension seals. This seal maintains the slightly larger gaps. Sold as a pair, two pairs needed per car.  Each package has 2 strips of 25 1/2" lengths. *NOTE* Do not over tighten the...

Price: $15.65

Buy Details

Availability: In-Stock Item
Item #: 26658 -

These feature all the original details. Quality rubber molded around a steel insert. Replaces Ford Part #: D1ZZ-6528182-B and D1ZZ-6528183-B.

Price: $1.85

Buy Details

Availability: In-Stock Item
Item #: 19966 -

These form a seal between your rear marker lights and the quarter panels. Replaces part # D1ZZ-15447. Sold as a pair.

Price: $16.45

Buy Details

Availability: In-Stock Item
Item #: 10517 -

This kit is designed for the Mercury Cougar and Ford Mustang A/C box.Replaces part # D1ZZ-18500-A.Check out our video below on how to replace a heater core! We used a '69 Cougar with A/C, but many of the same concepts apply to other years.

Price: $88.05

Buy Details

Availability: In-Stock Item
Item #: 41669 -

Reproduction plastic seat backs for the 1971 Cougar or Mustang.Sold as a pair

Price: $32.85

Buy Details

Availability: Out of Stock
Item #: 33243 -

New Old Stock passenger side eat back release knob for 1971-73 Mercury Cougar and Ford Mustang with outboard mounted seat back releases. Also fits 1971 and newer Mercury Comet and Ford Maverick with bucket seats, as well as 1971 and newer Pinto.Ford part number D1FZ-6262622-A. *Note - Not to be confused with the center mounted release knobs.

Price: $34.15

Buy Details

Availability: In-Stock Item
Item #: 10583 -

Very nice reproduction knobs for 1971-73 Mercury Cougar and Ford Mustang with outboard mounted seat back releases. Also fits 1971 and newer Mercury Comet and Ford Maverick with bucket seats, as well as 1971 and newer Pinto. *Note - Not to be confused with the center mounted release knobs.

Price: $49.86

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 31640 -

Used seat back stop for the 71 - 73 Cougar or Mustang. Right is same as left.  Sold individually, two per car.

Price: $32.75

Buy Details

Availability: In-Stock Item
Item #: 10584 -

Very nice reproduction knobs for 1971 Mercury Cougar and Ford Mustang with center mounted seat back releases. Also fits 1971 Mercury Comet and Ford Maverick with bucket seats, as well as 1971 Pinto. *Note - Not to be confused with the outboard mounted release knobs.

Price: $23.99

Buy Details

Availability: In-Stock Item
Item #: 41830 -

Great looking replacement style seat belts. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colors. Please note: this is the only aftermarket shade of Aqua, which was only used on the Ford Mustang. Contact us for availibility of good used Cougar correct aqua seat belts.Sold individually

Price: $45.75

Buy Details

Availability: In-Stock Item
Item #: 13711 -

These are era-correct looking seat belts at an affordable price.  These are not Concours reproductions, but have the correct vintage look used by Ford on multiple cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals.Sold individually Includes: 1 Complete non-retracting seat belt (includes both male and female side)2 Bolts, nuts, and lock washers

Price: $41.18

Buy Details

Availability: In-Stock Item
Item #: 13708 -

These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included!sold individually

Price: $41.18

Buy Details

Availability: In-Stock Item
Item #: 13714 -

These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included!sold individually

Price: $45.75

Buy Details

Availability: In-Stock Item
Item #: 13706 -

These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included!sold individually

Price: $38.25

Buy Details

Availability: In-Stock Item
Item #: 32360 -

Finally! A cure for those peeling chrome bezels on your car with deluxe seat belts. If your plastic bezels on your 68-72 standard belts are two part construction, you can upgrade with these attractive bezels. Before these were reproduced we used to hunt high and low for good used units from rear belts out of parts cars. Perfect fit and great quality. Sold as a pair, six per car on coupes, four per car required on convertibles. Replaces Ford part # C8AZ-65611A72-A

Price: $70.65

Buy Details

Availability: In-Stock Item
Item #: 30898 -

Now you can restore your 1968-72 Cougar or Mustang’s deluxe seat belt buckles back to their original showroom condition by replacing cracked, broken, or missing components with the new seat belt buckle restoration kit. Tooled to the original factory specifications from OEM quality injected molded black plastic. This seat belt buckle kit features the correct texture grain pattern and starburst medallions for a perfect restoration. The release button and spring are included. One kit does a pair...

Price: $45.75

Buy Details

Availability: In-Stock Item
Item #: 13715 -

These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included!Sold individually

Price: $45.73

Buy Details

Availability: In-Stock Item
Item #: 13709 -

These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included!Sold individually

Price: $45.75

Buy Details

Availability: In-Stock Item
Item #: 13710 -

These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included!sold individually

Price: $45.75

Buy Details

Availability: In-Stock Item
Item #: 13712 -

These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included! sold individually

Price: $45.73

Buy Details

Availability: In-Stock Item
Item #: 13707 -

This is an original looking seat belt at an affordable price. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included! SOLD INDIVIDUALLY

Price: $13.37

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 32041 -

Used seat belt anchor plate that has been cut out from a car in our salvage yard. Must be welded to floor pan. 6 total per car, 2 inboard in the transmission tunnel, and 4 on the rear seat pans. The front outboard anchors are part of the rocker rails. Rectangular shaped like the 1967-73 cars. We have noticed that the last generation 1971-73 Cougars had 4 round shaped plates in the rear floors. Same threads, all work the same. These were pretty much used on all Ford cars starting in...

Price: $13.37

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 32042 -

Used seat belt anchor plate that has been cut out from a car in our salvage yard. Must be welded to floor pan. 4 total per car, all 4 on the rear seat pans. The front outboard anchors are part of the rocker rails. Rectangular shaped for the front seat belts inboard on 1971-73 cars. Round anchor bracket with factory welded nut for added strength. See related items for good used seat belt anchor plates if you have concours needs. Replaces Ford Part # D1AZ-6561216-A. ...