1971 Ford Mustang

Nuts and washers for attaching the rear differential carrier or pumpkin or third member to the rear axle housing. Correct for all 1969-73 Mercury Cougar and 1969-73 Ford Mustang. 8 inch or 9 inch third members, all the same.

Correct size and style white square plastic insert that clips onto front or rear license plate bracket on any 1967-73 Mercury Cougar. Each kit allows one license plate to be mounted. The actual screw has a large head which is made for license plates, but is not the factory Ford style of fastener for Concours judged cars. We also sell an accepted original style of screw, see item 8286.

New rubber "O" ring for Ford V-8 distributors from 289/302/351W/351C/429 engines.

Brightens the engine compartment and looks sharp. Fits our big block finned aluminum valve covers (item# 26018) and others with the round push-in style opening. Requires a rubber grommet to fit into the valve cover, which is usually included with new valve covers.Does NOT fit valve covers with the "stovepipe" fitting (like our small block finned aluminum units) or factory valve covers the tabs for twist-on oil caps. This cap is for after market valve covers.

Brightens the engine compartment and looks sharp. Fits aftermarket valve covers only. These require a rubber grommet to fit into the valve cover. Please Note: This oil cap DOES NOT fit the finned "G" valve covers we sale, as they are built to OEM specs.

Original used oil filler cap adapter for any 1967 Mercury Cougar or 1965-67 Ford Mustang. This is for use with the open emissions, push on oil cap. This adapter allows for slip-on type oil caps to be used on valve covers with the twist-on style cap hole. 1.25" O.D. Will most definitely need a new gasket. These will ship "as found" or fresh from our wrecking yard. Photo is most cases will show a cleaned part for glamour photography shots. Also have reproduction version.Ford part...

This adapter allows for slip-on type oil caps to be used on valve covers with the twist-on style cap hole. 1.25" O.D.

Nice reproduction oil dipstick made from all stainless steel. Only fits 289 or 302 Ford engines from 1967-73. These dipstick tubes have the 'full' and 'add' markings in the correct place, however they do not have any Ford part numbers stamped on them. Black steel as shown, not plain shiny steel like originals.Replaces Ford part # C7OE-6750-B or C8OE-6750-B.

Engine oil dipstick as found on most any 1970-73 Ford with 351 Cleveland engines (H, or M Code), 1972-73 (Q code). Ford used several different suppliers and there are differences that show up in the finger handle as shown. Top of the shield to the dipstick end is approximately 21-11/16 inches. The handles were painted blue originally. Ford part # D0AZ-6750-A, Ford casting # D0AE-6750-A.*NOTE* In 1970 351W engines also were designated as H codes, 351W has 6 bolts attaching the valve covers,...

Quality After-Market oil filter for the 1967 - 1973 V-8 Mercury Cougar or Ford Mustang. Better filter than OEM.

Bare Metal oil pan. Has no paint, chrome, or protective coating. Replaces Ford Part #: C5ZZ-6675

Includes drain plug

Nice reproduction oil pan, painted stock Ford blue on the exterior.

[No Description Provided]

Includes drain plug.

Reproduction Small Block Painted Oil Pan for the Mercury Cougar or Ford Mustang 289 or 302

Used oil screen pick up tube assembly from a small block Ford 260, 289, or 302 engine. This is for most front sump 260, 289, or 302 engines in Ford cars up to at least 1972. Used item, should be degreased and cleaned inside and out prior to installation. Tube assemblies with damaged screens, damaged tubes or bends are thrown away or scrapped. We only save undamaged, used oil pick up tubes. Melling sells a quality reproduction of this item.* Excludes 351W and 351C engines, and all F Series...

Hex shaped extension. Made from machined metal. Highly polished and Chrome plated. Replaces Ford Part # : C2OZ-9B339-C

Hex shaped Oil Pressure Sending Unit Extension. Mounts the oil pressure sensor away from the engine blockConstructed from steel with a durable zinc finish. 1/4" NPT male & female ends plus an additional 1/8" NPT female port for items requiring an auxiliary oil pressure source. Eliminates the need for a T-fitting adapter when adding an aftermarket gauge or sensor. Replaces Ford Part # : C2OZ-9B339 and D1UZ-9B339-DP

Hex shaped extension. Made from machined metal and Zinc plated. Replaces Ford Part # : C2OZ-9B339

Hex shaped extension. Made from machined metal. Used and road tested steel extension for installing your oil pressure sending unit. Part shipped normally will not be as clean as the one pictured, we strongly suggest cleaning the inside oil passage prior to installation, it is a used part. Fits all 289, 302, 351W, 390, 427, 428CJ engines. Several versions found on this item. Steel and aluminum construction. We have both in the bin. Please note that the 351C or 351 Cleveland engine has the it's...

Reproduction overflow hose with smooth outer wall. Hose length 36"

Reproduction disc brake pedal pad for the Mercury Cougar or Ford mustang equipped with a manual transmission. This unit is a perfect fit! Replaces Ford part # C5ZZ-2454-D.Fits: 1967 Mercury Cougar1968 Mercury Cougar 1969 Mercury Cougar 1970 Mercury Cougar 1971 Mercury Cougar 1972 Mercury Cougar 1973 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang 1969 Ford Mustang 1970 Ford Mustang 1971 Ford Mustang 1972 Ford Mustang 1973 Ford Mustang ...

This great fitting reproduction emergency / parking brake pedal pad for the Mercury Cougar or Ford Mustang. This is supposed to have a stainless steel retaining ring around the perimeter. We carry both reproduction and used. Replaces Ford part # C9ZZ-2454-A.

Reproduction foam rubber donuts that help cushion the brace from the tail panel on any 67 - 73 Cougar or Mustang.Replaces Ford part number C5ZZ-6540996Sold as a set of 4.

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. This ORR LAC chassis black paint will give the appearance of an expensive, baked on finish. Also usable on other tools, equipment, vehicle frames, shop racks, trailers and more. ORR-LAC 923 Semi Gloss black.

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. This SEM Trim Black paint is a satin black acrylic coating, formulated to match the OEM finish on automotive trim parts. Good for use on plastic, aluminum, steel, stainless steel and chrome. Great for refinishing grilles, taillight bezels, vinyl top trim, pinch weld blackout, and more.No primer...

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT.This VHT roll bar and chassis paint will give the appearance of an expensive, baked on finish. Heat resistant to 250 degrees, this epoxy coating also resists chemicals, rust, corrosion and salt. No primer is needed. Also usable on other tools, equipment, vehicle frames, shop racks, trailers and more. ...

VHT epoxy paint is great for a number of applications. It's a unique one step protective coating that dries quickly and doesn't require a primer. It provides excellent rust, corrosion and chemical resistance which, needless to say, is ideal for anything you're doing under your hood or under and around the body of your car. One can covers about 12 - 14 square feet.

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. SEM brand COLOR COAT paint is formulated to match, restore or change color on most vinyl surfaces, flexible and rigid plastics, carpet and velour. COLOR COAT is fade resistant, flexible and is a semi-permanent coating. We do not recommend this product for driver side arm rests, door pull straps, shift...

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. This is a GOOD match for 1967-68 Cougar parchement / off-white interiors. SEM brand COLOR COAT is formulated to match, restore or change color on most vinyl surfaces, flexible and rigid plastics, carpet and velour. COLOR COAT is fade resistant, flexible and is a semi-permanent coating. We do not...

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. New SEM aerosol flexable paint for the Mercury Cougar or Ford Mustang. This is a great match for the 1967, 1968 and 1969 dark blue interior color. SEM brand COLOR COAT is formulated to match, restore or change color on most vinyl surfaces, flexible and rigid plastics, carpet and velour. COLOR...

This charcoal black aerosol paint is a very close match to the original finish used on 1967-68 Cougar XR-7 lower dash structures and steering columns. We've tried it ourselves and have been satisfied with the results. Our only critique is that it's a bit slower to dry than other paints we're used to. The AccuMatch(TM) Interior Paints are the result of years of work and perfectly match the original color shades. Each color has been expertly color-matched. Paints feature extra-high pigment...

Professional grade paintless dent removal kit. This kit is designed to work with smaller blemishes such as dents from hail, door dings, etc. Complete with universal high strength glue sticks, puller, and a variety of different sized gluing tabs. NOTE: Remove glue with 91% alcoholAlthough we work with 67 - 73 Cougars and Mustangs, this kit is good for a wide variety of different vehicles.

Replacement cork pan gasket for all 1965-73 C4 Ford transmissions. 

Cork pan gasket for the C6 transmission on any 1967-73 and 1967-73 Mercury and Ford. Rubber gasket also available.

Rubber pan gasket for the C6 transmission on any 1967-73 and 1967-73 Mercury and Ford. Cork gasket also available.

Rubber pan gasket for the FMX transmission on any 1969-73 and 1969-73 Mercury Cougar and Ford Mustang.

New black screw for attaching the black plastic automatic shifter bezel on any 1971-73 Mercury Cougar or Ford Mustang. Should also be for Mercury Comet and Ford Mavericks with floor shift automatic automobiles. #8 x 1/2 black pan head screw. Replaces Ford part # 52017-S2See related items for set of 4 screws as a kit. Check out our video on rebuilding your shifter below: ...

New black (set of 4) screws for attaching the black plastic automatic shifter bezel on any 1971-73 Mercury Cougar or Ford Mustang. Should also be for Mercury Comet and Ford Mavericks with floor shift automatic automobiles. #8 x 1/2 black pan head screw. Replaces Ford part # 52017-S2 Check out our video on rebuilding your shifter below: ...

Pan head screw for attaching the sport mirror glass assembly into the passenger side painted sport mirror head. Found on all FoMoCo products utilizing a manual mirror 1969 - 1973. 8-32 pan head screw with Phillips screw head. Do you have questions about installing a passenger side mirror or using Riv-Nuts? ...

Reproduction anti rattler board - 1/8" panel board that prevents rattling noise. Installs on top of fuel tank on the side where the jack and spare tire mount. Measures 16" X 12"

NOS air cleaner breather element filter assembly for all 1970-73 Mercury Cougar and most all Fords with V-8 engines. This filter fits inside your air cleaner base, a hose connects to the fitting and goes to the PCV valve in the valve cover. Sold as shown, "AUTOLITE" marked also FA-79.  Casting number D0OF-9D696-A. Ford part number D0OZ-9D695-A.

Replaces Ford part #C7AZ-6892. For round hole with two notches, aluminum or steel valve covers.

Reproduction PCV Plastic Ring for the 1970 and 1971 Mercury Cougar or 1970 - 1971 Ford Mustang with the 429 Cobra Jet or 429 Super Cobra Jet. Decal Text: AutoliteEV-48C9TZ-6A666-A Replaces Ford Part #: C9TZ-6A666-A.

A needed part for giving your car a tune-up. PCV Valve fits all years; 289, 302, 351, 390, and 428 CID; V8. *Note - Not technically correct for 390-4V or 428CJ, those originally used a PCV valve with a threaded top, and the 90° elbow - part number C7OZ-6A706-A.

Powerful oil filled coil that generates 40,000 volts, designed to work with the either of our Pertronix Ignitors. Sold in black or chrome. *Note - This coil is not necessarily needed with the Pertronix Ignitors, the stock Ford coil works fine for most applications.