Brakes

New front Inner wheel bearing with cup / race for original drum and disc brakes for all 1970-73 Mercury Cougar and 1970-73 Ford Mustang with V-8 engines. These are tapered bearings with cone or race. Inner diameter is 1.378 inches. These are dry bearings, meaning they will need to be packed with chassis bearing grease, prior to installation. A smaller outer bearing and this inner bearing are required for each side. Two of each needed for the front wheels. *Note - This bearing only fits the...

New front outer wheel bearing with cup / race for original drum and disc brakes for all 1970-73 Mercury Cougar and 1970-73 Ford Mustang with V-8 engines. These are tapered bearings with cone or race. Inner diameter is 0.865 inches. These are dry bearings, meaning they will need to be packed with chassis bearing grease, prior to installation. A large inner bearing and this outer bearing are required for each side. Two of each needed for the front wheels. *Note - This bearing only fits the...

Bleeder screw for your 1968 - 1973 Cougar or Mustang Calipers.

Bolt and nut for installation of disc brake pedals in any 1967-73 Mercury Cougar or Ford Mustang. See related items for plastic bushings and metal spacer.

New rubber boot for brake push rod to the master cylinder on all drum brake cars. Fits all 1967-72 Mercury Cougar and 1965-73 Ford anything cars, including Mustang.Trivia - Did you know that 100% of all 1973 Mercury Cougars, came from the factory with front power disc brakes?

Used brake hose support bracket for all 1971-73 Mercury Cougar and Ford Mustang. This attaches with two bolts to the driver side rear frame rail, it supports the flexible brake hose that goes to the rear axle. Ford had two versions of this part, picture shows the early version, later versions had a chunk cut off of the corner. Replaces Ford part number D1ZZ-2073-A, and D1WY-2073-A.

Reproduction brake and fuel line clamp kit for Mercury Cougars and Ford Mustangs equipped with drum brakes.

Rear Wheel Cylinder (29/32", Right Hand) Fits either Right Hand or Left Hand. Sold individually, 2 required per car. Replaces Ford Part #: C3OZ-2262-B and D2ZZ-2262-B.

Reproduction driver side (left hand) front wheel cylinder for 10 inch x 2-1/4 inch drum brakes. This unit fits in a 1-1/8 inch hole on the brake backing plate. Replaces Ford Part #: C3OZ-2062-B, D2ZZ-2062-A, & D3ZZ-2062-A.

Reproduction passenger side (right hand) wheel cylinder for 10 inch x 2-1/4 inch drum brakes. This unit fits into a 1-1/8 inch hole on the brake backing plate. Replaces Ford Part # C3OZ-2061-B, D2ZZ-2061-A, & D3ZZ-2061-A.

Reproduction drum brake backing plate hole cover plug. Replaces Ford Part # 8A-2092.

Used driver side (left hand) front drum brake backing plate for 2-1/2 inch brake shoes on the Mercury Cougar or Ford Mustang, and Fairlane / Torino equipped with 351 or larger V8 engines. Ford part # C9OZ-2013-B. *NOTE* Excludes 1969-71 Mustang and other Ford/Mercury with 302 engines, which normally came with 10" x 2-1/4" drum brakes on the front.

Used passenger side (right hand) front drum brake backing plate for 2-1/2 inch brake shoes on the Mercury Cougar, Ford Mustang, and Fairlane / Torino equipped with the 351cid or larger V8 engine.Ford part # C9OZ-2012-A. *NOTE* Excludes 1969-71 Mustang and other Ford/Mercury with 302 engines, which normally came with 10" x 2-1/4" drum brakes on the front.

This option includes paying a core charge. By choosing this option, the rebuilt booster you receive will have started the rebuild process as an average quality core.We highly recommend that you send us your core first. Here's why:We can core match your booster. Boosters that are rebuilt using a superior quality core are always reserved for core matching. If your core is average or below average, you may be able to pay to upgrade to a rebuilt booster that started the rebuild process as a...

This option REQUIRES sending your core in advance. Here are the advantages of pre-sending your core:We can core match your booster. Boosters that are rebuilt using a superior quality core are always reserved for core matching. If your core is average or below average, you may be able to pay to upgrade to a rebuilt booster that started the rebuild process as a superior quality core.You can find out the quality of your core before paying a core charge and avoid unnecessary core charges....

Quality rebuilt LH disc brake caliper for 1968-1973 Cougar / Mustang. Hardware not included. Check out out video on converting from drum to disc brakes below: ...

Quality rebuilt RH disc brake caliper for 1968-1973 Cougar / Mustang. Hardware not included. Check out out video on converting from drum to disc brakes below: ...

Used drum brake distribution block for Mercury Cougar and Ford Mustang equipped with front drum brakes. This unit mounts to the driver side fender apron with two nuts. Bare block without brake switch. Plan on testing and or rebuilding before installation. Rebuild kits available.Ford part # D0OZ-2B257-B. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts...

These new brake drums are perfect replacements for tired and thin originals on you Cat or Pony. Fits cars with either the 2 1/4 inch or 2 1/2 Inch shoes. Front drums do not include studs or a hub. Drums Provide Consistent Quality & Reduced Noise.; Drums Are Vehicle Specific & Meet Federal Safety Standards.; Castings Meet Sae J431/g3000 Specifications For Proper Tensile Strength.; Machined To Control Perpendicularity & Run-Out For Optimal Performance & Brake Life.Also fits V8...

Quality replacement brake drum. # of Bolt Holes : 5 Inside Diameter : 254 mm Bolt Circle Diameter : 114.3 mm Brake Drum Surface Depth : 71.6 mm Center Bore Diameter : 61.8 mm Maximum Discard Diameter : 256.3 mm O.D. : 296.3 mm Replaces Ford Part #:C2OZ-1126-B

STOPFLEX?? incorporates a special 4 layer design for superior strength and virtually no volumetric expansion. It starts with a Teflon PTFE core (liner) which is wrapped first in a Kevlar braid, followed by an elastomer barrier and then it's strengthened further by the outer stainless steel braid. Replacing original equipment rubber hoses with STOPFLEX?? stainless steel braided hoses will increase braking performance by doing away with the soft spongy brake pedal. Rubber hoses expand, with the...

Flexible high pressure replacement brake hose for the driver (left hand) side on Mercury Cougar and Ford Mustang equipped with disc brakes.Replaces Ford part # D1ZZ-2078-B.

Flexible high pressure replacement brake hose for the passenger (right hand) side of Mercury Cougars and Ford Mustangs equipped with disc brakes.Replaces Ford part # D1ZZ-2078-A.

Please note, this is a Mustang rear brake hose and the fittings are different for the Cougar. Flexible high pressure replacement brake hose for rear drum brakes on Ford Mustang that attaches to the rear end housing.   Replaces Ford part # D1ZZ-2282-A.*NOTE* If you have ordered a reproduction Cougar brake line from the front of the vehicle to the rear axle you will want to make sure which fitting you have as many of the reproduction cougar brakes lines come with the incorrect mustang...

Two-piece Stainless Rear Axle Brake Line Set 71, 72 & 73 Mercury Cougar and Ford Mustang with the 8" or 9" Rear Axle. The Rear Axle Brake Lines are mounted on the axle going to the left and right rear wheels. These will either connect to a caliper hose or thread directly into a wheel cylinder. All lines come Pre-Bent and flared with the correct threaded fittings which reduces your install time tremendously. These stainless-steel lines are T304 but are of a special softer blend to help...

Two-piece OE-Style steel Rear Axle Brake Line Set 71, 72 & 73 Mercury Cougar and Ford Mustang with the 8" or 9" Rear Axle. The Rear Axle Brake Lines are mounted on the axle going to the left and right rear wheels. These will either connect to a caliper hose or thread directly into a wheel cylinder. All lines come Pre-Bent and flared with the correct threaded fittings which reduces your install time tremendously. These mild steel lines are Galphan coated for added protection. ...

All new disc brake pads are supplied to us by brand name manufacturers. Boxed sets of four pads.

All new premium disc brake pads are supplied to us by brand name manufacturers. Set of 4 pads. Low dustProtective underlayerRubber/steel/rubber layered shimScorched

Longer arm than drum brake pedals. Comes with all mounting hardware. Pedal shipped bare, picture may show hardware and pedal pad with trim. Most of these pedals are dated as shown. It makes it fairly easy to identify them by year.

Reproduction drum brake pedal pad for the Mercury Cougar or Ford Mustang equipped with an automatic transmission. The 1967 version of this piece is narrower than this 1968-73 piece.Replaces Ford part # C6OZ-2457-A.

Reproduction brake pedal pad for the Mercury Cougar and Ford Mustang equipped with a manual transmission and drum brakes. This unit is a good fit and is a quality part. Replaces Ford part # C5ZZ-2457-G.

Excellent quality replacements. Includes hub, studs, and bearing races. Single piece design. 2" spacing from hub to rotor face

Used driver (left hand) side brake shoe adjustor for Mercury Cougar or Ford Mustang. This screw assembly is part of the manual and self adjusting system for your drum brakes either front or rear. These have right and left handed threads depending upon which side of the car they are intended. Left side screws are identified by an "L" on the end of the screw under the socket and a single groove machined into the pivot nut. Original Ford part number for the passenger (right hand) side is...

Used passenger (right hand) side brakes shoe adjustor for Mercury Cougar or Ford Mustang. This screw assembly is part of the manual and self adjusting system for your drum brakes either front or rear. These have right and left handed threads depending upon which side of the car they are intended. Right side screws are identified by an "R" on the end of the screw under the socket and a two grooves machined into the pivot nut. Original Ford part number for RH or passenger side is C2OZ-2041-A,...

New front10 X 2-1/2 inch brake shoes for the Mercury Cougar or Ford Mustang. These will fit the rears of some Ford vehicles, but not a Cougar or Mustang without modification.Typically this size of brake shoes is only found on the front of a Cougar or Mustang. You would have to have 2-1/2 rear backing plates in order to use these shoes on the rear of your car.

Premium grade of rear brake shoes with semi metallic brake linings. 10 inch diameter drum brakes. Please measure your brake shoes, there are also 1-3/4 inch wide shoes too.

Bushing that goes to the inside of the brake booster pushrod. This is the early version of this part that is made of plastic, a later version was introduced in 1969 which was made of nylon and is/was more durable.

Reproduction bushing for the master cylinder push rod where the switch and brake pedal converge. Two required per car and the bushings are sold separately.Ford part number C5DZ-2B129-B

These reproduction brake and clutch pedal bushings are made from high strength plastic that is wear resistant. Two are required for automatic cars, four for manual transmission cars. Sold as a pair. Replaces Ford part # B7AZ-2471-A.

Premium, reproduction, and near concours correct front emergency / parking brake cable for the Mercury Cougar or Ford Mustang. This cable hooks onto your inside foot activated brake assembly inside the car, through the floor board, and hooks to the brake equalizer cable under the car. This unit is very close to an OEM replacement, much better than our economy cable. ...

This used emergency / parking cable anchor bracket is spot welded to your passenger side (right hand) front floor pan and anchors the cable. Comes "as taken from parts car". *Customer Feedback* from mercurycougar.net: "Best guys to always talk to about Cougars..will take the time on the phone with you, call you back if you leave a message, got all the time in the world for you when your talkin 'cause your important to them. Greatest thing for our hobby. Thanks Lin and Don for making/getting...

Reproduction concours correct premium grade passenger side (right hand) emergency / parking brake cable for the 1970-73 Mercury Cougar and Ford Mustang with V-8 engines. This is the long one on the passenger side (right hand) and measures approximately 133-1/8 inches long.

Reproduction emergency / parking brake cable for the Mercury Cougar or Ford Mustang with V-8 engines, that is approximately 133 1/8" long. This unit fits from equalizer to rear brakes and one is required per vehicle.Replaces Ford part # D0ZZ-2A635-A.

Premium grade reproduction driver side (left hand) rear emergency / parking brake cable. This is the short one, 31 inches, located on the driver side and is an exact fit for 1970 - 1973 Mercury Cougar and Ford Mustangs. Ford Part # D0ZZ-2A635-B

Front emergency brake cable bracket that welds to the floor under the drivers side floor board.  It is spot welded to the floor pan and frame rail and is often over looked when floor pans are replaced. The unit you receive will need clean up, but will not be heavily rusted. Fits all 1971-73 Mercury Cougar and Ford Mustang.

Keeps proper tension on emergency / parking brake cable by taking up the slack when the brake is off. Hook attaches to the bracket under the passenger side floor. Replaces Ford Part # C7ZZ-2A808-A.

Keeps proper tension on emergency / parking brake cable by taking up the slack when the brake is off. Hook attaches to the bracket under the passenger side floor. Replaces Ford part # C7ZZ-2A808-A.

Reproduction disc brake caliper insulators for a large array of FoMoCo products starting in 1968. 2 are required per caliper, 4 total per vehicle. Sold as a pair.Replaces Ford part # C8AZ-2B299-A.