Your cart is empty!
Our shopping cart requires the use of cookies. If you have your cookies disabled, please enable them for our site to place an order. If you have cookies enabled and have added an item to your cart, but you are still seeing this message, that could indicate that the cookie for our shopping cart is corrupted on your computer.You should be able to fix this by either:
Buy Details
Reproduction fuel line to side apron grommet for the Mercury Cougar or Ford Mustang. 3 needed per car.Replaces Ford part # D1ZZ-9288.
For use with your original Carter fuel pump on Cougars equipped with a BOSS 302, GT 390, 428 Cobra Jet or 429 Cobra Jet.
New replacement carburetor mounting gasket for 1970-73 Ford 351C or 351 Cleveland engines. Mounts between the fuel pump housing and the engine.
Exclusive to WCCC, here's our reproduction in-tank, fuel sending unit with the low fuel option. Good for all 1971 - 1973 Mercury Cougar XR7's and all Ford Mustangs with 16 gallon fuel tanks. This is a reproduction of a 1971 fuel sending unit with three prongs (2 electrical and 1 alignment prong). The original Ford casting number was D1WF-9275-AC. This unit comes with a new 3/8 inch filter, brass float, and sending unit gasket. These are completely interchangeable on all 1971 - 1973 20 gallon...
This is the two prong version fuel sending unit for 71 - 73 Cougars and Mustangs. The reason for the two prong, is that this particular year used a ground wire coming off of the sending unit. Cougars equipped with the convenience control package, and the XR7's used a three prong version. The function however is not as good as original but adequate and usually will work for years. If you have an original, often times it's just the float that needs replacing, so don't be quick to discard your...
This is the stainless steel, two prong version fuel sending unit for 71 - 73 Cougars and Mustangs. The reason for the two prong, is that this particular year used a ground wire coming off of the sending unit. Cougars equipped with the convenience control package, and the XR7's used a three prong version. These units are better than original being made from stainless. The function however is not as good as original but adequate and usually will work for years. If you have an original, often...
Ford called this part the fuel vapor separator. It mounts to the top of the fuel tank. This is part of the emissions control smog system, the fuel vapors that are collected in the charcoal canister are returned through a hose to this device into the fuel tank. Applications for this part include: 1971-73 Mercury Cougar and Ford Mustang, 1971-72 Pinto and Bobcat, 1971-72 Maverick and Comet, 1971 Thunderbird and Lincoln MKIII, and 1971-73 Ford / Mercury full sized cars. Starting about 1973, this...
Reproduction full length driver side floor pan. This pan is technically for 67 - 68, but will work for 67 - 73 Cougars and Mustangs. There were small differences such as drain holes / no drain holes etc. between the years, but will work for all years. Hi, and sincerely thanks for all help I've received from WCCC during my (mega) 1968 restoration project. If everyone would be that helpful, the world would be a much better place. ;-) My car is almost ready for the road, but - as always - there...
Reproduction full length passenger side floor pan. This pan is technically for 67 - 68, but will work for 67 - 73 Cougars and Mustangs. There were small differences such as drain holes / no drain holes etc. between the years, but will work for all years.
C8OZ-14A187-A Unique 1/4"-20 bolt for attaching the fuse blocks. 69 70 71 72 73 Mercury Cougar Ford Mustang fuse panel attaching bolt. Includes "C" clip and spring as shown. "C" clip keeps the bolt in the black fuse block.
C8OZ-14A068-A Black Bake-O-Lite original fuse block. Grade A, no cracks or chips. Perfect for upgrading your broken fuse block that has a nice wiring harness. 69 70 Mercury Cougar Ford Mustang fuse panel. Sometime in the later part of 1972 Ford switched to a nearly identical brown fuse block.
C8OZ-14A068-GRADEB Black Bake-O-Lite original fuse block. Grade B, not broken, but will have chips from prying out fuses. Perfect for upgrading your broken fuse block that has a nice wiring harness. 69 70 71 72 Mercury Cougar Ford Mustang fuse panel. Sometime in the later part of 1972 Ford switched to a nearly identical brown fuse block.
C8OZ-14A033-C Brass clip with accessory terminal for attaching the accessory lead wire with multi connector. Attaches to all 1969-70 fuse blocks found on Mercury Cougars and Ford Mustangs. Accessory feed terminal for such things as 1969 swing away steering column, rear window defogger, speed or cruise control, etc. Includes fuse block mounting hardware.
For use with 1967 390 and all 1968-73 air cleaner lids except Ram Air which uses no gasket. Replaces Ford part #C8ZZ-9673.
New carburetor gasket for most 1967-73 2 barrel carburetors. 289/302/351W/351C engines. Replaces Ford Part #: C3AZ-9447-B *Excludes 1968 X code 390-2V premium fuel engines.
Round ring shaped gasket that goes on top of the carburetor. Protects and seals the carburetor to the air cleaner.
[No Description Provided]
New Old Stock Ford small block Ford distributor shaft to engine block gasket, made of rubber. Fits all 260, 289, 302, 351w, 351c engines. 1959-76. This is a "O" ring rubber washer. Will not fit big block FE, 360, 390, 410, 427, 428 engines. Ford part number B9TF-12143-A.
New Old Stock Ford FE distributor shaft to engine block gasket, made of rubber. Fits all FE or 352, 360, 390, 410, 427, 428 engines. 1958-76. This is a tapered rubber washer. Will not fit small block Windsor or Cleveland engines. Ford part number B8A-12143-A.
Ford FE distributor shaft to engine block gasket, made of rubber. Fits all FE or 352, 360, 390, 410, 427, 428 engines. 1958-76. This is a tapered rubber washer. Will not fit small block Windsor or Cleveland engines. Ford part number B8A-12143-A.
Replaces Ford part #D1AZ-6522428. Sold individually.
Made from fuel resistant cork like original. Modeled off the Mustang \ 69 Cougar gasket which has 5 screws (67-68 Cougar only used 4 screws), but works for any 67-73 Mustang / Cougar. For 67-68 Cougar applications you will have to just screw through the cork. We can say with out a doubt, that in both Dearborn and San Jose, the factory workers did not use the pre-drilled holes when installing the fuel filler necks. We have suggested that the supplier not make them with holes. Probably...
Replaces part #C0AF-9276-A. Goes between fuel sending unit and tank.
Door lock and trunk lock gasket as found on all 1969-73 Mercury Cougar. Gasket used to seal the lock cylinders to the exterior door on all 1967 - 1973 Mercury Cougar and Ford Mustang as well as the trunk lock gasket on all 1969-73 Mercury Cougar. It is not used for the trunk lock cylinder on the 1967 - 1968 Mercury Cougar because they uses a flip up trunk lock cover that instead uses a gasket between the covers housing and the trunk. Replaces Ford part #C7AZ-6243625.
Gasket, for the C6 transmission filter. Fits all c-6 transmissions 1967-73 Mercury Cougar and Ford and Mustang.
One piece molded rubber gasket with metal core. Keeps the rails flat and rigid, and prevents damage from over-tightening. Made by Fel-Pro. Oil pan SnapUps are included for easy mounting. This is by far the best oil pan gasket on the market.
OEM style cork oil pan gasket for the 429 Cobra Jet on the 1971 Mercury Cougar or Ford Mustang.
New outer axle gasket for any 8 or 9 inch Ford rear end with 28 splined axles. Common on all Mercury Cougar and Ford Mustang with V-8 engines. Excludes 31 splined axles as found on Boss and Cobra Jet cars. One required per side, two per car.
Replaces Ford part #C7AZ-13568
Thermostat Housing Gasket BY FEL-PRO® Replaces Ford Part #: C5AZ-8255-A.
Thermostat Housing Gasket BY FEL-PRO® for the 351 Cleveland.
Adhesive-Backed Gasket Material Helps Prevent Breaking of Water Outlet. Gasket Cement is Not Needed. Self-Adhesive Backing Holds Thermostat in Place While Water Outlet is Being Installed.
New water pump gasket for 1971 Mercury Cougar and Ford Mustang with 429CJ engines. Water pump to water pump plate gasket only.
New water pump gasket for 1971 Mercury Cougar and Ford Mustang with 429 Cobra Jet engines. Single gasket, seals engine to water pump plate only. Also fits the 360 engine. Will also fit Torino, Comet and Cyclone.
New gaskets for installing your intake manifold. This is the Felpro branded gasket. Fits 1964-73 small block Ford engines with size 260/289/302 cubic inches. C code 289-2V, A code 289-4V, F code 302-2V, and J code 302-4V.*Note - Excludes 1969-70 Boss 302 engines.
New gaskets for installing your intake manifold. This is the Felpro branded gasket. Fits all 1970-73 Ford 351C engines with 4 barrel intake manifolds 1969-70 Mercury Cougar and Ford Mustang with 351C-4V engines. This gasket set includes a metal valley pan.Any doubts? 351 Windsor engines have 6 bolts holding the valve covers in place. 351 Cleveland engines have 8 bolts holding down the valve covers.*Note - Excludes 351W engines. *Note - Excludes 351C-2V Cleveland engines. ...
New gaskets for installing your 429 Cobra Jet intake manifold. This is the Felpro branded gasket. Fits 1970-71 Ford 429CJ engines. 1971 Mercury Cougar and Ford Mustang with J or C code 429CJ engines. Intake to cylinder head gaskets and intake end pieces, along with O ring for distributor. *Note - Excludes N code 429-4V or Thunderjet, passenger car engines.
New timing cover gasket set for 1970-73 Mercury Cougar and Ford Mustang with 351C engine. Includes gaskets as shown, timing cover, water pump to timing cover, fuel pump, crankshaft seal, and oil pan saddle.
Cork gasket for the disc brake splash shield. Fits all 1968-73 Mercury Cougar and Mustang and 1968-71 Ford mid size including Torino, Cyclone, Ranchero, Fairlane.Replaces Ford part number C8OZ-2B160-A.
Reproduction pair of taillight lens to housing gaskets for the 71 - 73 Mercury Cougar.
Cork valve cover gaskets for any 289/302/351W Ford engine. Sold in pairs, works well with either stamped steel or cast aluminum valve covers. Excludes Boss 302.
Rubber valve cover gaskets for any 289 302 351W Ford engine. Sold in pairs, works well with either stamped steel or cast aluminum valve covers. Excludes Boss 302.
NEW PRODUCT! This gauge tester can be used to test all gauges on any Ford vehicle from 1956 to 1983. We are privileged to be one of the first companies able to offer this new product that has long been needed by the classic car community. Now you can quickly determine if the gauges in your car are accurate with this gauge tester. You can verify the high medium and low reading for your gauges, and also shows that the Instrument Voltage Regulator is working. If you own a...
Four piece CLEAR window glass set for the 1971, 1972 or 1973 Mercury Cougar convertible with MANUAL windows. Kit includes drivers door glass, passenger door glass, drivers quarter window glass and passenger quarter window glass.This glass does not have the faint Car-Lite markings in the corner but rather very bold, large SAFETY GLASS in raised letters that cannot be removed without special equipment. Many feel a few minor scratches on an original look better than the raised white lettering...
Reproduction clear four piece glass set for the Mercury Cougar or Ford Mustang convertible equipped with power windows. This set does not include any of the window trim so save yours for reuse. There are three versions of this glass. The clear version is just that, clear with no tint. There is a tinted version that will have a slight green tint to the glass. There is also a second tinted version that is called smoked and this version has a grey / brown tint to the glass. The clear and the...