Contact Us / Visit Us (click here)
If the Shopping Cart takes too long to respond, you can bypass the shopping cart and go straight to the checkout page by clicking the following link: Checkout.
International Customers Click Here [Updated 1/2024]
Loading Trivia . . .

Search This Category:
Select layout:
Products (Click sub-categories above to ONLY display results for that Sub-Category) 49-96 of 2535
Price: $9.77

Buy Details

Availability: In-Stock Item
Item #: 16000 -

Reproduction diaphragm pump that mounts on the front all 67 - 73 Cougar or Mustang Autolite 2V carbs as well as 1967 Autolite 4V Carbs. With today's gas, these commonly fail, especially when sitting for extended periods of time. Complete failure will cause fuel leaks, but many times these will affect performance well before a leak actually starts. Good idea to replace every few years or if sitting for 6 months or more. Replaces Ford Part #: C4AZ-9B559-A.

Price: $2.88

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 41376 -

Floor shifter access plug. 1967-73 Mercury Cougar and Ford Mustang, also fits floor shift 1971+ Mercury Comet and Ford Maverick. Ford Part number C7ZZ-7C147-A. Check out our video on rebuilding your shifter below: ...

Price: $30.47

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 15-0112 -

This is the part of the tilt switch that the turn signal wand screws into. This part is always included when you purchase a new turn signal switch. 1967-69 mechanism has two springs on either side, the 1970-73 mechanism uses just one spring. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many...

Price: $49.86

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 30990 -

Used actuator for the seat back release on the 1971 - 1973 Mercury Cougar or Ford Mustang. This item is tested and will be in working condition. Left is the same as right, two required per car. Sold individually.

Price: $19.65

Buy Details

Availability: In-Stock Item
Item #: 30956 -

Reproduction center cap adapter kit for installing Legendary center caps on the Legendary Series GT9 wheels. The spacing is a bit deeper on these specific wheels, so this adapter kit comes with special adapters and longer screws.  This kit is intended to make original and after market Mag 500 and Style Steel wheels center caps work on the Legendary Series GT9 wheels.  Please note that the included screws may not fit the thread pattern of some center caps.  The plates will...

Price: $8.95

Buy Details

Availability: In-Stock Item
Item #: 14-0009 -

3M brand weather strip adhesive for installing the various rubber weather stripping found on Mercury Cougars on all years. This is the yellow colored adhesive, the factory used yellow adhesive on the weather stripping and is the 2 ounce size.

Price: $15.56

Buy Details

Availability: In-Stock Item
Item #: 14-0010 -

New 5oz tube of yellow weatherstrip adhesive for installing the rubber weatherstripping found on the Mercury or Ford. This 3M brand adhesive is a great match to the yellow colored adhesive that Ford used to attach the weatherstripping on many of it's vehicles back in the day.

Price: $0.98

Buy Details

Availability: In-Stock Item
Item #: 30880 -

This stepped window trim clip is great for times when your stainless trim just will not click into place. We have found that the reproduction cougar rear window gasket is a little taller than OEM and this adjustable clip allows you to compensate. Another instance this multi-fit clip works is when someone has replaced one or more nail-heads that the clip fastens to and located them in the wrong place.Sold Individually. These clips attach to posts built in to the car. In case you're missing some...

Price: $61.85

Buy Details

Availability: In-Stock Item
Item #: 26202 -

The Proper ignition advance curve is vital for maximum performance, economy (gas mileage) and drive-ability. Ford / Mercury owners had few acceptable choices with regard to adjusting the vacuum curve with their OEM distributor. You could fumble with the stock washers, fiber stops and springs (a hit-or-miss exercise in frustration!) or you could spend the money on an adjustable after market vacuum advance that looks completely out of place and cost you major judging points. This works on any...

Price: $25.88

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 25035 -

Used alternator adjusting arm for any 1970-73 Mercury Cougar, Ford Mustang, or generally Ford anything with 302, 351, or Boss 302 engines. This can be used on 1973 cars, Ford did switch to a different alternator bracket that tightened the alternator from the back sometime in 1973. Replaces Ford part number D0OE-10145-A, listed in the Motorcraft catalog as GY-938Also fits:Comet Montego

Price: $50.85

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 25101 -

Alternator adjusting bracket found on 429 engines. Not technically correct for 1970-71 429CJ engines, this is the passenger car version. The true 429CJ alternator bracket is slightly different and extremely hard to find. This is a very good and economical substitute. Has Ford part number D0SE-10145-A stamping.

Price: $58.25

Buy Details

Availability: Out of Stock
Item #: 10487 -

This high performance alignment kit replaces the factory eccentric bolt and cam that holds the lower control arm to the frame. The eccentric cam is used for setting wheel camber. When the eccentric is turned, the lower arm moves in or out changing camber. Stock eccentric cams can slip or rotate going over bumps, allowing the alignment to change. Which is the cause of many worn tires. The lower control arm adjusting cam eliminator kit replaces the eccentric bolt and cam with non slipping...

Price: $29.88

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 23391 -

384543-S8 Power steering pump adjusting spacer for use without air conditioning. For most 1970 - 1973 Mercury Cougar or Ford Mustang with 351C engines. Spacer dimensions: 7/16" I.D. and 1/2" thick.*Note 1970 and later cars with 302 or 351W engines use a 3/4 inch spacer.

Price: $125.35

Buy Details

Availability: In-Stock Item
Item #: 15704 -

This air cleaner assembly never came from the factory on any Cougar, but was an over the counter option available from your Ford dealer. If you have a very nice hood blanket I would think twice before using it in conjunction with this air cleaner assembly as it will leave an imprint. To avoid this problem with small block cars you can use a lower profile carburetor spacer, but on big block cars this is not an option due to the already thin design of the factory carburetor spacer. This will...

Price: $14.15

Buy Details

Availability: In-Stock Item
Item #: 26287 -

This is a reproduction of the original engine displacement round decal, Chrome background with gold followed by black and chrome checkerboard followed by gold background with chrome Cougar logo, followed by black and chrome checkerboard followed by black background with gold CJ 429-4V followed by black and chrome checkerboard followed by gold background with chrome Cougar logo, followed by black and chrome checkerboard. located on the top of the air cleaner.Outside diameter: 13 1/4"Fits...

Price: $10.89

Buy Details

Availability: Out of Stock
Item #: 20672 -

Stud that the factory line workers used for locating the air conditioning pedestal bracket. Then backed up with a nut. Used on 351C / 429CJ pedestals from 1970 - 1973.*Note - Excludes 289 / 302 / 351W / 390 / 428CJ engines.

Price: $0.85

Buy Details

Availability: In-Stock Item
Item #: 27449 -

Reproduction stud and nut assembly that the factory line workers used for locating the air conditioning pedestal bracket. Then backed up with a nut. Used on 289 / 302 / 351W / 390 / 428CJ pedestals from 1967 - 1973. Stud is threaded into the cylinder head for easy installation of the cast iron pedestal bracket.*Note - Excludes 351C and 429CJ.

Price: $148.95

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 11-0046 -

Complete heater and air conditioning control assembly that includes a bezel or face plate, knobs, bracket control mounting plate, electrical and vacuum switches. Functional, driver quality, heater control assembly for your Mercury Cougar and Ford Mustang until 1-3-1972. Does not include the indicator light plug and harness. Ford part # D1ZZ-19A884-A. *Restoration Tip* You can purchase some plastic polish (or try toothpaste) and polish for the lens back to new. Find a silver paint pen...

Price: $28.05

Buy Details

Availability: Out of Stock
Item #: 19974 -

This Filters Last 40% Longer & Holds 53% More Dirt Than Most other Filters. * This filter fits primarily Big Block cars, but a couple of other combinations, so grab a tape measure and double check the height of the one you need to replace, as that will tell you which one you need. Air Filter Height (Inches) : 2.193" Air Filter Height (mm) : 55.7 mm  Air Filter Bottom I.D. (Inches) : 11.32" Air Filter Bottom I.D. (mm) : 287.53 mm Air Filter...

Price: $23.27

Buy Details

Availability: In-Stock Item
Item #: 19978 -

These filters feature the correct color of filter paper and an red/orange molded face. In addition, they have the correct "round hole" design on the outer shell. Fits Mustang 1965-67 K code HiPo 289 and 1968 Mercury Cougar GT-E W code 427-4V engines, that were originally equipped with the chrome high performance air filter assemblies. Please note: this filter will NOT fit a standard Ford air cleaner Replaces Ford Part #: B7SZ-9601-A. ...

Price: $31.62

Buy Details

Availability: In-Stock Item
Item #: 19977 -

Correct dimensions, good fit. Will show minor cracks in rubber but will not affect performance and cannot be seen when installed. Replacement air cleaner for the 1967 - 1973 Mercury Cougar Walking Cat Oval Air Cleaner, as well as other Ford oval air cleaners.

Price: $21.05

Buy Details

Availability: Out of Stock
Item #: 19975 -

This Filters Last 40% Longer & Holds 53% More Dirt Than Most other Filters. Please note that the Ford Service Replacement specs for this filter (Service Replacement # D7AF9601AA) are; Type: 67; Inside: 13.000; Outside: 11.200; Height: 2.795. All reproductions that we have found follow these specs, making the filter 1/8" taller than the original filters. These filters will function properly, but the lid will not seat properly. ACTUAL FILTER SPECS: Air Filter Height (Inches) : 2.822...

Price: $27.15

Buy Details

Availability: In-Stock Item
Item #: 42013 -

This 1965 Mustang alignment pin is not correct for the 1969 to 1973 Cougar but it will work. See the image to the left to see the comparison to an original 69 pin.

Price: $36.45

Buy Details

Availability: In-Stock Item
Item #: 14305 -

If after installing a new stereo system you experience unwanted motor whine or engine noise, check all grounds on radio, amp, etc. If you still have the noise, this filter may help.Instructions included.

Price: $64.05

Buy Details

Availability: In-Stock Item
Item #: 11643 -

Nice reproduction of the original alternator wiring harness, 2 pin individual colored boot style connector and wire colors match up to the original Ford drawings. Application is 1971 Mercury Cougar standard models or 1971 Ford Mustang with factory tachometer option, all with 351/429CJ engines. Ford service number D1OZ-14305-B. *Caution, not for use with Cougar XR7 models or Mustang with ammeter gauge.

Price: $70.95

Buy Details

Availability: Out of Stock
Item #: 11820 -

Replaces Ford Part # D2ZZ-14305-C, D3DZ-14305-B, D2ZZ-14305-G & D3ZZ-14305-C Door Tag 65D & 76D

Price: $67.55

Buy Details

Availability: In-Stock Item
Item #: 41449 -

Reproduction Alternator Harness without Instruments for the 1971 Mercury Cougar

Price: $81.35

Buy Details

Availability: In-Stock Item
Item #: 11642 -

Nice reproduction of the original alternator wiring harness, 3 pin individual colored boot style connector and wire colors match up to the original Ford drawings. Application is 1971 Mercury Cougar XR7 models or 1971 Ford Mustang without factory tachometer option, all with 351/429CJ engines. Ford service number D1ZZ-14305-B. *Caution, not for use with Cougar standard models or Mustang with alternator warning light

Price: $14.85

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 33477 -

This plate is what is located on the backside of your door jam where your striker threads in on the driver side.

Price: $14.85

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 33478 -

This plate is what is located on the backside of your door jam where your striker threads in on the passenger side.

Price: $18.86

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 31591 -

Threaded anchor that slides into the trunk hinge on each side. Sold individually, two needed per car. These are for Cougar and Mustang built after approximately 3/31/1971. Look for bolt spacing of 4-1/4 inches on those trunk lids.  Ford number C9AZ-6242752-A.*Note - Trunks prior to March 31, 1971, did not use this anchor plate. I think that they had a bolt spacing of 4-1/2 inches.

MSRP:$40.00
Price: $38.18

Buy Details

Availability: In-Stock Item
Item #: 26005 -

Designed for optimum AM/FM reception. Excellent solution where a conventional antenna is not desirable (ie you do not want the antenna sticking out of the top of your fender), or when you want a power antenna or just better reception without having to replacing the factory antenna with a non-original looking antenna. Allows for complete removal of factory antenna or for the factory antenna to be disconnected and left in place to maintain the factory look.  Multiple mounting options...

Price: $28.45

Buy Details

Availability: In-Stock Item
Item #: 14352 -

This economy reproduction is not an exact copy, but does have a similar rectangle base. This is not a retractable antenna. Replaces part # C8ZZ-18813-A.

MSRP:$97.99
Price: $89.15

Buy Details

Availability: In-Stock Item
Item #: 14358 -

Very correct kit for the 1971-72! Not only does this kit include all the correct hardware, but also a photocopy of the original Ford template showing where to place the antenna on the passenger side fender. The rectangular base gasket is actually not correct for a Mercury Cougar as it has a Ford Mustang part number and is of a different shape and thickness (see comparison photo). To retain the exact, correct angle on your 1971 - 1973 Mercury Cougar mast you will want to reuse your thicker...

MSRP:$5.00
Price: $4.55

Buy Details

Availability: In-Stock Item
Item #: 26563 -

Mustang part that has incorrect thickness and a slightly different overall geometry to it. We also carry the correct Cougar version of this gasket, but only in used form.Replaces part # D1ZZ-18898.

Price: $11.88

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 11-0213 -

D1ZZ-223A58-A Lower door guide insert to prevent rattling of the window. Two of these inserts are inserted into the lower door guide after the door glass run is installed. Plastic piece that is subject to cracking. Two needed per door, item sold individually. Click on images to enlarge. ...