Engine & Under Hood

Round ring shaped gasket that goes on top of the carburetor. Protects and seals the carburetor to the air cleaner.New Old Stock Ford gasket, Ford part number C5ZZ-9654-B.

Used original heat riser / S tube for 1968, 1969, and 1970 Cougar and Mustang 428 Cobra Jet / Super Cobra Jet. These will seldom be available. The one pictured above is the best example we've ever seen - removed from the car in 1969 just days after purchase. The pictures below are a more realistic example of the used condition you might expect. There are also additional comparison shots next to the reproduction S tube we also sell. The differences are small but the most obvious is the fact...

These steel tubes made to exact O.E.M. standards and specifications.

C8OZ-9A603-B metal shroud that attaches to the passenger side stock cast iron exhaust manifold. Works in conjunction with a metal 'S' tube sold separately (C8AZ-9652-A). R code and Q code Cobra Jet engines only.

If you are not looking to match the part numbers of your original hinges, we recommend considering our PREMIUM quality reproduction that is made of thicker material than the originals for added durability and is far superior to any previous reproduction. This listing is for you folks out there who want the correct part number on your hinge. Good used OEM original hood hinges that are available individually or as a set.   We carefully inspect these hinges before sending them...

C7ZZ-6A664-B Original used hose that connects the original threaded PCV valve combination with C7OZ-6A706-A elbow and the 390 PCV transfer tube on the intake manifold. Molded hose with 5/8" valve end and 1/2" tube end. All 1967-68 S code 390GT or 390-4V engines and 1968-69 428CJ and 428SCJ engines, includes Cougar, Mustang, Fairlane, Torino, Ranchero, Cyclone, and Comet. Used hoses will have faded striping (if present), and clamp impressions. Very often the rubber will be hard and showing some...

Generic hose kit that will fit the 289 or 302 for those who are not concerned about the CONCOURS look. Used on both the 20" and 24" wide radiators Replaces Ford Part #'s C4ZE-8260-A and C4ZE-8286-A. For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check out our video: ...

NOS Air conditioning belt tension pulley for Cougars and Mustangs with the 289 or 302 engine built between 1/3/1967 and 3/1/1968.  Ford part # C7AZ-8678-B. NOTE* Send in your old core for a credit toward the purchase of this NOS pulley. *NOTE* Must be used with the C7AA-2888-G cast iron lateral support brace. ...

Looks right and it works, but belt alignment will be off. Needs about 1/8 inch of shim to align with the other pulleys. See pictures. This adjustable bracket and pulley can be used on all 1968 - 1973 Cougars or Mustangs with the V-8 engine as long as they have the "stamped steel" lateral air compressor support brackets. This bracket will only have the big bearing pulley and may have various casting numbers such as D5TA-8A617, D3OA-8A617, D5OA-8A617, D8OA-8A617, etc. This is a...

New old stock bracket and pulley assembly for Cougars or Mustangs equipped with the 289, 302, or 1969 351W engine. We also offer a bearing replacement service to rebuild your 289, 302, or 1969 351W fixed idler pulley, see item 27539. Ford part # C8AZ-8678-C. ...

Used fixed idler bracket and pulley assembly with new installed bearing for 1968-69 Cougars and Mustangs with the 390 or 428CJ engine. This part will have a small bearing on the pulley and is not marked with a casting number. The 1970 bracket and pulley assembly was a service replacement part and are the same as the 68-69 with the exception of a slightly larger bearing. This later service replacement part is an economically priced service replacement for the earlier originals. All pulleys come...

C8OZ-3C511-B Rear power steering pump support bracket. Also called the high pressure hose indexing bracket. For any 1968 - 1970 Cougar or Mustang with any of the 390 / 427 / 428CJ engines. OEM used part designed to maintain the position of the high pressure power steering hose from coming in contact with with moving or high heat parts. *Note - May or may not work with non-original or replacement high pressure hoses.

C8TE-9425-A Cast iron intake manifold used on all 1968 X code 390-2V engines in a Mercury Cougar or Ford Mustang. Stock 2 barrel intake manifold, used after 1-9-1968. Take off manifold with correct casting number of C8TE-9425-A. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C5AZ-9424-R. *Installation Tip - A 1 inch aluminum spacer plate with PCV provision is needed for proper air cleaner clearance. ...

C7TE-9425-G Cast iron intake manifold used on all 1968 X code 390-2V engines in a Mercury Cougar or Ford Mustang. Stock 2 barrel intake manifold, used before 1-9-1968. Take off manifold with correct casting number of C7TE-9425-G. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C5AZ-9424-P. *Installation Tip - A 1 inch aluminum spacer plate with PCV provision is needed for proper air cleaner clearance. ...

Cast aluminum Sidewinder intake manifold. Over the counter speed part for the 427 Medium Riser. The offset carburetor placement was to help provided equal length runners in regards to flow. Single 4 barrel intake manifold as shown. Looking closely at the photos, this one has had a repair performed in the past. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford casting number C6AE-9424-J.

Rechromed GT air cleaner lid for the Mercury Cougar and Ford Mustang equipped with either the Boss 302, GT 390, or 428 CJ engine without the shaker option. It was possible to order a 390 GT motor for your Cougar without ordering the 390 GT package. Cougars equipped with the S code 390 6.5 Litre engine, that did not come with the GT package, would have used the painted air cleaner lid. Replaces Ford part # C7OZ-9661-A.*NOTE* The outside dimension of the lid is 16.75 inches and will not fit the...

This used assembly includes lamp socket, bracket, mercury switch, and length of wire.Replaces part # C7ZB-15702-A

Used engine or 'motor' mount for any 1969 Mercury Cougar or 1967-69 Ford Mustang convertible. There is not a replacement engine mount for the 1967 cars with 289 engine. These have the Ford casting number of C7ZA-6038-F, in the rubber. The mounts that we have in stock are a 30 year accumulation, needless to say it is very limited supply. They all appear to be in good shape without cracks in the rubber. We offer them for those enthusiasts that want correctness for concours judging, we suggest...

These Brackets are made from stamped steel just like the original, and built to Ford specifications for an exact fit. Available in correct OEM Black. customers looking for a little more flash under the hood might be interested in the highly-polished stainless steel version of this bracket! Replaces Ford Part #: C7ZZ-8A193-A. Check out our video on Radiator and Fan upgrades below: ...

Application is for the FE engines 390, 427 428. This assembly is needed for the installation of the cylinder head air supply tubes. Sold as one nut / one ferrule. 8 total needed for smog tube attaching. Originally these were installed in conjunction with a lower tube.

Used 1970-72 black AUTOLITE marked oil fill cap with black plastic elbow. Several variations noted from our collection, AUTOLITE and MOTORCRAFT versions. Will need detailing or fresh black paint applied. Would also suggest replacing the rubber grommet. These 50 year old rubber grommets are rock hard and likely leak air. Gasket to valve cover will also need replacement. Even though this cap has a 1971 parts number, we see these on the 1970 351C engines quite often. Replaces Ford part...

Precision machined to the factory specifications. Light gold anodize finish just like the original.

Concours correct dipsticks for 1967 - 1969 big block engines. These are exact reproductions of the originals with the proper length and oil level for these big block FE's. They have all of the correct markings including the Ford part number and recommended oil weight. Each dipstick is finished with a show quality chrome handle capped with the correct plastic plug. Ford part # C7OZ-6750-A, Ford casting # C7OE-6750-A.

The oil filter made by the original Ford supplier.

New Old Stock oil filter adapter from any 1968-70 Ford with 390 or 428CJ (non SCJ). Fits Cougar, Mustang, Torino, Fairlane, Cyclone, Ranchero, etc. Nice cast aluminum bracket for installing the spin on oil filter and oil pressure sending unit. Ford casting number C8AE-6881-A. Will fit 1967 FE engine blocks too. Those technically used an adapter with a casting number of C0AE-6881-A.

Famous 'Cal Custom' aluminum finned oil pan that was so popular throughout the 60's, 70's and 80's. It has not been available for years, but it is back again. Pan is made from all new pressure die cast tooling and then fully machined to offer a precise fit and leak free installation. These look great in combination with the Finned Air Cleaner and Valve Covers. Replaces Ford Part #: C5ZZ-6675.

Includes drain plug.

Used oil screen pick up tube assembly from a FE or big  block 1966-70 Ford car, such as 352, 390, 410, 428, or 428CJ engine. This is for most front sump oil pans. Used item, should be degreased and cleaned inside and out prior to installation. Tube assemblies with damaged screens, damaged tubes or bends are thrown away or scrapped. We only save undamaged, used oil pick up tubes. Melling sells a quality reproduction of this item. Replaces Ford Part #: C6OZ-6622-A ...

New pair of white and yellow paint sticks for the Mercury or Ford. These units were used by FORD at the assembly plants to mark fender aprons, radiator support, transmission, rear end housing, sheet metal, glass and variety of other parts. It's often little details like this that separate first and second place at the show.

Front steel vacuum fitting for 390, 427, 428CJ engines. New Old Stock. Replaces Ford part number C7AZ-9A474-A.

C7AE-6A666-B is stamped on this used PCV valve. Absolutely correct for 1968 390GT, 427-4V GT-E, and 428CJ Mercury and Ford cars. Must be used with either of the 90° elbows available, reproduction or OEM Ford.. This is used, no guarantee that it functions like new. Ford MPC number C7OZ-6A666-A. There is a published procedure for refurbishing these valves. These positive crankcase ventilation valve can be disassembled. ...

Used threaded PCV valve for use on 390-4V, 428CJ, 427-4V cars from 1967-70. Unknown functioning condition, these have the correct threaded tops and work with either of the 90° elbows available, reproduction or OEM Ford.

Pertronix brand 7mm spark plug wires. These are performance oriented wires compared to the concours spark plug wires. For any 1967-73 Mercury Cougar and Ford with 289 or 302 engines. Black wires and boots, quality spark plug wires taylor made for the small block Ford engines. Recommended by Pertronix for use with the Flame Thrower coils.

Ford part number C8AZ-6A312-A. Application 390-2V, 390-4V engines, and 428 Cobra Jet with air conditioning. Power steering optional, with dual alternator belts. Ford casting number C8AE-6312-A. Triple sheave 68 crank pulley.

1968 390-4V all with factory manual transmissions and factory air conditioning. Pulley diameter 5.89" inches. Ford part number casting # C8AE-9B480-B. Mounting bolts sold separate.

C8OZ-8509-C 1968 427 / 390-4V without air conditioning and 1968-1970 428CJ without air conditioning. Thermactor on all applications, power steering optional. 3 sheave pulley with two different diameters. The MPC lists it as 6 inches on the dual sheave portion and 5-1/16 inches on the outer but we find the actual outer most measurements to be 6 1/8" wide on the dual pulley and 5 3/16" wide on the single sheave pulley. When laid on a flat surface the height is 2 3/8" tall. Ford casting number...

Used FoMoCo 20 inch small block radiator. This is for a 1968 Mercury Cougar or Ford Mustang with 289-2V, 302-2V, or 302-4V and automatic transmission (code w). Used core radiator for recoring and restoration. Typical Dearborn installed assembly line radiator. Factory installed automatic transmission radiators came with the fittings in the bottom tank for transmission cooling. Current listing is dated 8FD or 4th week of June 1968. Very late production date.Replaces Ford part number C8ZE-8005-H1 ...

Used Western Modine (W/Mo) 24 inch big block radiator. This is for a 1968 Mercury Cougar or Ford Mustang with 289-2V, 302-2V or 302-4V engines and (automatic code W) transmission. Used core radiator for recoring and restoration. Typical Dearborn radiator, only FoMoCo on the top tank. 1968 Mercury Cougar or Ford Mustang. This is the typical radiator installed at the San Jose, California assembly plant. W/Mo embossed on the top of the tank with a date. Dated 67-10 or October...

Used WMo or Western Modine 24 inch small block radiator. This is for a 1968 Mercury Cougar or Ford Mustang with 289-2V, 302-2V, or 302-4V and 3 or 4 speed manual transmission. Used core radiator for recoring and restoration. Typical San Jose installed assembly line radiator. Factory installed manual transmission radiators did not come with the fittings in the bottom tank for transmission cooling.Replaces Ford part number C8ZE-8005

Used 24 inch big block radiator. This is for a 1968 Mercury Cougar or Ford Mustang with 390-2V or 390-4V and C-6 (automatic code U) transmission. Used core radiator for recoring and restoration. Typical Dearborn radiator, only FoMoCo on the top tank. 1968 Mercury Cougar or Ford Mustang. Replaces Ford part number C8ZE-8005

Used WMo or Western Modine 24 inch big block radiator. This is for a 1968 Mercury Cougar or Ford Mustang with 390-2V or 390-4V and C-6 (automatic code U) transmission. Used core radiator for recoring and restoration. Typical San Jose installed assembly line radiator. Dated 67 12. Replaces Ford part number C8ZE-8005

These concours quality Chrome caps are made in America and bear all the original markings. O.E.M. details include original letter style, "S.M.C.O." and "Autolite". Pound rating is stamped on cap. Replaces Ford Part #: C7ZZ-8100-A.

Concours appearance with black case and authentic Autolite markings. Disappointing functionality, often will fail in less than a year. We recommend buying the genuine Motorcraft version instead, or even one of the generic versions we also sell. *NOTE* There are dozens of styles which were produced by several manufacturers. This unit represent the most common type and is marked C7AF-11450-A1 & "AUTOLITE". When you see this icon on a product, it means it's a sub-par item that we don't recommend,...

Brass sensor that screws into intake manifold and activates temperature gauge in dash. Replaces Ford Part #: C6DZ-10884-B (SW-552) or C9WY-10884-A (SW-888)*. Temp Sender Switch Temp Rating : 15.2-19 Ohms Resistance At 220 Deg F Temperature Switch Thread Size : 3/8" x 18 NPT * - The 1969 351 Windsor temperature sending unit has been discontinued. Most manufacturers list the 1968 302 temperature sending unit as the closest replacement.Check out the video below on our new gauge tester: ...

NOS new old stock Motorcraft water temperature sending unit, fits Ford 289, 302, 390, 427, 428CJ. 260° stamped, for Mercury Cougar 1967-69, and Ford Mustang 1966-69.  Ford number C6DZ-10884-B. *Note - these are specifically NOT for 1969 351W. Ford had a unique part number for that one engine.... and we don't stock that one. Sorry. Check out the video below on our new gauge tester: Check out our video on replacing the fuel system on a '68 Cougar! ...

Used Autolite water temperature sending unit, fits Ford 289, 302, 390, 427, 428CJ. 260° stamped, for Mercury Cougar 1967-69, and Ford Mustang 1966-69.  Ford number C6DZ-10884-B. *Note - these are specifically NOT for 1969 351W. Ford had a unique part number for that one engine.... and we don't stock that one. Sorry. Check out the video below on our new gauge tester: Check out our video on replacing the fuel system on a '68 Cougar! ...

Left side Thermactor smog tube with the jog and bracket around the coil. Bare tube, installation hardware is not included. Not always available, hard to keep on the shelf, look for our reproduction tube set (right and left) available soon. Must have the correct cylinder heads with the drilled and tapped holes for these tubes. Also called air manifold, this unit is part of the air manifold assembly.

Right side Thermactor smog tube. Installation hardware is included as shown. Not always available, hard to keep on the shelf, we always have the reproduction tube set (right and left) in stock. Must have the correct cylinder heads with the drilled and tapped holes for these tubes.