1972 Mercury Cougar

Our heater cores are the finest available anywhere for any price. Constructed from corrosion resistant copper and brass. A great buy for anyone who is sick of smelling anti-freeze and needing to make repairs to this vital part.Replaces Ford Part #: D1ZZ-18476-B. Check out our video below on how to replace a heater core! We used a '69 Cougar with AC, but many of the same concepts apply to other years. ...

Concours correct yellow striped heater hose that features durable yellow striping with "Motorcraft" spelled out and dated LQ1H04A. Correct for all V-8 engines WITHOUT air conditioning. The hoses for cars with A/C have a molded 90 degree elbow at the end that fits on the water valve side. Some length trimming may be required for a tight looking fit. Turn those hoses so that the yellow striping shows!Replaces part # D2ZZ-18472-Y

Concours correct yellow striped heater hose for Cougars and Mustangs WITH factory or integral A/C. These hoses feature durable yellow striping with "Motorcraft" spelled out and dated LQ1H03A. Correct for all V-8 engines with A/C. This hose has a correctly molded 90 degree elbow that fits on the water valve side. Some length trimming may be required for a tight looking fit. Turn those hoses so that the yellow striping shows!Replaces part # D3ZZ-18472-ACY ...

Bolt for the under side convertible plate on any 1969-73 Mercury Cougar or Ford Mustang. 6 total bolts needed for attaching reinforcement plate to undercarriage. Sold individually. These are a close match to the original bolts, which are 3/8-16 x 1-1/2". Ford tightening specs. are 25-38 lbs. ft. torque.Replaces Ford number 57048-S2.

Machine hex bolt for installing the heater cables to the climate controls on any 1969-73 Mercury Cougar or Ford Mustang. 8-32 threaded hex machine screw like the originals. Attaches cables for heater only or factory A/C cables.

This H5006 bulb is the closest Halogen Reproduction of the original FoMoCo headlights that we carry. This bulb has the number 2 at twelve o'clock (to indicate its position in your grille) just like the original, and the FoMoCo logo is actually formed into the glass rather that being etched onto it, as is on some other repros. This high / lo beam is definitely going to be brighter than your original dim bulbs. Also note: Other than Cougars, only the 1969 Mustang used these bulbs.Don't forget...

This H5001 bulb is the closest Halogen Reproduction of the original FoMoCo headlight that we carry. This bulb has the number 1 at twelve o'clock (to indicate its position in the grill) just like the original, and the FoMoCo logo is actually formed into the glass rather that being etched onto it, as is on some other repros. This high beam is definitely going to be brighter than your original dim bulbs. Note: Other than Cougars, only 1969 Mustangs used these bulbs. Don't forget that you need to...

Used hinge for any 1971-73 Mercury Cougar or Ford Mustang. Comes as shown, we select the best hinges to inventory.Replaces Ford part number D1ZZ-6506050-A.

Good used cut off driver side, trunk or deck lid hinge. Fits all 1971-72 Mercury Cougar and Cougar convertible models. Sometime in 1972, the hole spacing for the trunk lid changed from 3 inches to 4-1/4 inches spacing. This hinge will have the 3 inch spacing. These are welded to the body, expect some cleanup to the metal prior to welding. We do not drill spot welds.Additionally fits 1971-73 Mustang hardtop and convertible models (body style 65 and 76). Ford part number D1ZZ-6542700 and...

Good used driver side trunk or deck lid hinge. Fits all 1972-73 Mercury Cougar and Cougar convertible models. Additionally fits 1972-73 Mustang hardtop and convertible models (body style 65 and 76). We also sell the driver side hinge individually. Sometime in 1972, the hole spacing for the trunk lid changed from 3 inches to 4-1/4 inches spacing. This hinge will have the 4-1/4 inch spacing. These are welded to the body, expect some cleanup to the metal prior to welding. We do not drill spot...

Good used cut off passenger side, trunk or deck lid hinge. Fits all 1971-72 Mercury Cougar and Cougar convertible models. Sometime in 1972, the hole spacing for the trunk lid changed from 3 inches to 4-1/4 inches spacing. This hinge will have the 3 inch spacing. These are welded to the body, expect some cleanup to the metal prior to welding. We do not drill spot welds. Note that there are an early and late style of these hinges. Early style has a bolt spacing of 3 inches for installing the...

Good used passenger side trunk or deck lid hinge. Fits all 1972-73 Mercury Cougar and Cougar convertible models. Additionally fits 1972-73 Mustang hardtop and convertible models (body style 65 and 76). We also sell the driver side hinge individually. Ford part number D1ZZ-6542700. Sometime in 1972, the hole spacing for the trunk lid changed from 3 inches to 4-1/4 inches spacing. This hinge will have the 4-1/4 inch spacing. These are welded to the body, expect some cleanup to the metal prior to...

Set comes with economy grade pliers and 150 hog rings, enough for one bucket seat, probably two.

This kit contains 500 hog rings, more than enough for two bucket seats and one bench seat.

Reproduction replacement hold down clamp for the distributor on any 67 - 73 Cougar or Mustang. Sold individually, 2 needed per car.

Crating Fee Applies To This Item. You will be contacted once your order is reviewed to discuss the crating fee. Crating fees generally run between $175 - $250 (this does not include truck freight charges). If an item has a crating fee, this usually indicates that it must ship via Truck Freight and can only be shipped to US addresses and select Canadian addresses. Grade A hoods have no rust under the lip, nothing more than a light skim coat of filler found anywhere, no damage in the hinge areas...

Crating Fee Applies To This Item. You will be contacted once your order is reviewed to discuss the crating fee. Crating fees generally run between $175 - $250 (this does not include truck freight charges). If an item has a crating fee, this usually indicates that it must ship via Truck Freight and can only be shipped to US addresses and select Canadian addresses. Our grade B hoods are 100% rust free with minor damage to the top side. Hoods are shipped via www.forwardair.com so check their site...

Four per car, mounts to fenders. Replaces Ford part #D1ZZ-16758

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Good used OEM original driver side hood hinge. Available individually or as a set. These are far superior to the off shore reproductions you see advertised everywhere. The reproductions are very difficult to make fit and do not last very long. We carefully inspect these hinges before sending them as used hinges are prone to wear in more than one area. It is easier to fit and adjust these hinges prior to installing the springs on them. Here is a helpful youtube video that shows you how to...

Good used OEM original passenger side hood hinge. Available individually or as a set. These are far superior to the off shore reproductions you see advertised everywhere. The reproductions are very difficult to make fit and do not last very long. We carefully inspect these hinges before sending them as used hinges are prone to wear in more than one area. It will be easier to fit and adjust the hinge prior to installing the spring on the hinge. Here is a helpful youtube video that shows you how...

Good used OEM original hood hinge set. Available individually or as a set. These are far superior to the off shore reproductions you see advertised everywhere. Fits 1971-73 Mercury Cougar and Ford Mustang. The reproductions are very difficult to make fit and do not last very long. We carefully inspect these hinges before sending them as used hinges are prone to wear in more than one area. Here is a helpful youtube video that shows you how to adjust your hood. Shipped with the springs.Ford...

A modern touch to this classic muscle car look. This kit is the same Scott Drake "Shelby Style" Billet hood pin kit offered by many other vendors.Kit includes 2 Hood Pins, 2 dowel pins, 4 Nuts to hold the dowel pins on, machined billet aluminum top plates for the top of the hood, 8 screws to hold the hood plates on and 2 tie down cables. The difference between this version and the deluxe version, is that these are Machined billet aluminum top plates and the deluxe is stainless steel. Common...

This kit is the same Scott Drake "Shelby Style" hood pin kit offered by many other vendors.Kit includes 2 Hood Pins, 2 dowel pins, 4 Nuts to hold the dowel pins on, plates for the top of the hood, 8 screws to hold the hood plates on and 2 tie down cables. The difference between this version and the deluxe version, is that these are chrome plated and the deluxe is stainless steel. Common consensus is that the holes for the pins were hand drilled at the factory, so the exact location varied from...

Correct stud configuration, size, and weight. This scoop was made by using an original 1972 Cougar GT scoop to make the mold. 1971-73 Cougar GT's, and the J code 429CJ with ram air, all used the same scoop. The dimensions are just like the original and measure 19-1/4" at the widest point on the front, 24-1/8" at the widest point at the rear, and 25-1/2" tall when stood on end and measured at its longest point. The scoop is 2-1/8" tall at the front middle when mounted on the hood. Paint job not...

Welded in hooked retainer for the rear seat back installation on any 1967-73 Mercury Cougar or Ford Mustang coupe or hard top body style. This bracket welds to the edge of the package tray. Two hooks per car, sold individually. We cut out a individual sections as shown. Make good measurements prior to removal of your old brackets. You will need to drill out the spot welds prior to installation. For sure that basic Ford part number is 62118.

This is the large horizontal bracket that reinforces the front bumper on any 1971-72 Mercury Cougar. This is one of 6 brackets needed for mounting the front bumper. These were bare steel and some of our used brackets will have some erosion or minor rust. Structurally they are fine. Replaces Ford part number D1WY-17A792-A.

The High tone is indicated in raised letters located on the perimeter of the horn. The 1971-73 almost uses the same horn and bracket as the 1967-68, but was mounted at a different angle, so if you have a 1971-73 you will need to loosen the screw that holds the horn to the bracket and rotate the horn to the correct position.  These horns are close but not actually correct for a Cougar. 1967-68 Cougars used part number C7WF-13802-B Lo / C7WF-13801-B Hi and 1971-73 used D0DF-13802-A Lo /...

Tested and working used Hi tone horn. The Hi tone is indicated in raised letters located on the perimeter of the horn. 1971-73 Mercury Cougar used part number D0DF-13801-A Hi tone. Every horn is bench tested and inspected for cosmetic defects, if they do not function properly, and pass a visual inspection, they get recycled. The used horns at WCCC can be used as-is or you can clean and detail them for you show car.

Tested and working used Lo tone horn. The Lo tone is indicated in raised letters located on the perimeter of the horn. 1971-73 Mercury Cougar used part number C8DF-13802-A Lo tone. Every horn is bench tested and inspected for cosmetic defects, if they do not function properly, and pass a visual inspection, they get recycled. The used horns at WCCC can be used as-is or you can clean and detail them for you show car.

Very nice reproduction of the steering wheel hub decal with the walking cat to fit the new Shelby steering wheels. Chrome outer rim with plastic black and silver horn button in the center.

NOTE: A FEW CUSTOMERS HAVE MENTIONED THAT THE INSTRUCTIONS MAY BE WRONG. SWITCHING PINS 1 AND 5 HAD A BETTER RESULT. IF YOU RECEIVE THIS PART AND ARE HAVING TROUBLE WITH THE INCLUDED INSTRUCTIONS, TRY SWITCHING TO SEE IF YOU GET THE SAME RESULTS. Make those horns sound like they should! These relay kits work just like my headlight relay kits to deliver full system voltage to your horns. Ford used horn relays on many vehicles into the early seventies. Unfortunately Mustangs after '65 and...

If you have already begun to install or have installed this item, it is not eligible for return or refund. This rim blow horn switch is made in the United States by Daniel Carpenter Mustang and is made from vinyl like original. When installing, make sure to massage the rim blow switch in place with counter clockwise, compacting strokes. Clockwise strokes (thumb motions) will stretch the switch and when you complete the installation you will find the part has become too long to fit in place...

Tested and working used pair of Hi and Lo tone horns. 1971-73 Mercury Cougar used part number C8DF-13802-A and D0DF-13801-A. Every horn is bench tested and inspected for cosmetic defects, if they do not function properly, and pass a visual inspection, they get recycled. The used horns at WCCC can be used as-is or you can clean and detail them for your show car.

Aluminum flexible tube that connects the vapor canister to the air cleaner. To give this the look of the originals that had a black paper exterior coating you can spray paint it flat black. If anyone knows of a source to buy the original paper coated foil tubes we would like to hear from you. Fits 1970 California Delivered Cars and all 1971 - 1973 Cars. Look for Buck Tag EV or EM. Preheat/Emission Control Duct.3ft long 7/8" O.D. 3/4" I.D. Replaces Ford Part #: D1UZ-9d667-A, D4HZ-9d667-A...

Reproduction brake booster hose for Mercury Cougar or Ford Mustang. Measures 12" long

New power steering pressure hose for late 1972 and all of 1973 Mercury Cougar and Ford Mustang with 351 engines. This was a re-engineered hose to eliminate that 1971-72 extra long hose that doubles back on itself. Has brass fitting for attaching the pump end steel tube fitting, you need to save that steel tube. Made in the U.S.A. Replaces Ford Part # D1ZZ-3A719-A

Concours for 1970 351C-2V and 351C-4V with correct ink stamped Ford script, 17 1/2" long including the 90 degree bend. Connects PCV valve to carburetor spacer plate. Other parts houses list this as a 71-73 but the 71-72 is 25" long (so it can reach to the front of the driver side valve cover) on both the 2V and 4v 351 Cleveland and this hose will not reach. This will work for the 1973 Q-code 351C-4V as the 73 mates to a metal tube and is only 11".This hose was originally installed from the...

D1OZ-6A664-B Original used hose that connects the valve cover mounted PCV valve and the carburetor spacer plate on 1971 through 1972 Mercury Cougar and Ford Mustang 351C or Cleveland engines only. Used hoses will have faded striping (if present), and clamp impressions. Very often the rubber will be hard and showing some degree of stress cracks. *Note - Excludes all 1969-71 351W or Windsor engines, 1970 351C or Cleveland, and 1973 351C engines. *Note - These molded and contoured hoses were...

Replaces Ford Part # : D1ZZ-17543

Reproduction 1/2" hose clamp, commonly used on the fuel lines. This clamp is smaller than the ones used on the power steering return line.

Reproduction Power Steering Return Line Hose Clamp for the 1967 - 1973 Mercury Cougar

Reproduction flex brake hose clip for the Mercury Cougar or Ford Mustang.

Exact fit, not generic 'One Size Fits All' hoses. Quality high pressure fittings. Contains both upper and lower Hydraulic Hose for a 1971, 1972 or 1973 Mercury Cougar or Ford Mustang Convertible Hydraulic CylinderClick on images to enlarge.

These are the best CONCOURS radiator hoses on the market. All made in the U.S.A. by Gates or Goodyear both suppliers to Ford Motor Co. Hoses are also approved by Ford Motor Co.

These are the best CONCOURS radiator hoses on the market. Ink stamped for all 1972-73 Mercury Cougar and Ford Mustangs with 351C engines. All made in the U.S.A. by Gates or Goodyear both suppliers to Ford Motor Co. Hoses are also approved by Ford Motor Co. Has "MOTORCRAFT" and Ford part number D2OE-8B274-DB ink stamped on the hose. Has OEM style hose clamps stapled onto them like the factory installed hoses.

Reproduction Concours correct windshield washer hose with ribbed outer wall. Hose is 101" and is cut-to-fit.Tee connector not included, you can find it here.You can find the nozzles here.

Good used unit with no cracks, only for the xr7.