1972 Mercury Cougar

Complete floor pan for the 1969-70* Ford Mustang or 1969-70* Mercury Cougar. This item ships direct from the manufacturer for most orders. This item must ship via truck freight. Shipping to business addresses tends to be less than residential addresses, sometimes substantially.This item ships direct from the manufacturer for most orders and must be shipped via truck freight, and CANNOT ship via UPS. Shipping to business addresses tends to be less than residential addresses, sometimes...

This is a complete set of four used headlight bulbs, marked with the FoMoCo logo. These sets come with two high beam and two low beam bulbs. Each bulb is tested by the electrical department. If you're trying to keep your Cougar or Mustang as close to original as possible, you should definitely grab a set.These bulbs are date coded, so if you want a particular date, be sure to mention it in the comments section of your order.  

15 Piece kit that includes quarter panel drain plugs.

NOS Motorcraft condenser for point type distributors on any 1969-73 Mercury Cougar or Ford Mustang with V8 engines. Ford part number C9AF-12300-B and C9AZ-12300-A.

This ashtray features correct plating, but customer reviews indicate that they are not a perfect fit and slightly different from the original, see reference photos above.  Replaces Ford part # D1ZZ-6504788-A.

Used ashtray for the 71 - 73 Cougar or Mustang. Customer reviews indicate that are differences between the original the reproduction, see reference photos above.  Replaces Ford part # D1ZZ-6504788-A.

Nice reproduction clear rectangular clock lens for consoles. Fits all 1971-73 Cougar and Mustang consoles. The only downside is that these lenses have a slight manufacturing flaw - there is a small crack in the hole for the clock knob (see pictures above.) Although you won't notice it unless you look closely, we prefer to be up-front about the products we sell. With that in mind, this is currently the only available reproduction lens for this application, and we think that it looks a lot...

Good used console clock surround bezel with no cracks, or peeling chrome. Engineering number on the backside reads D1ZB-15017-AA

New chrome finish screws for attaching OEM consoles. Screws fit all stock consoles 1967-73 on Mercury Cougar and Ford Mustang, most any Ford consoles actually. Phillips head oval. 1967-68 consoles use 4 attaching screws, 1969-70 consoles need 6 along the outside, 1971-73 consoles have a total of 8 screws along the outside. These are 1-1/2 inches long like the originals.

Made to concours standards. Replaces Ford Part # D1ZZ-6506024-A

Mini console assembly, comes with ashtray receptacle, wiring and socket, and console with a casting number of D1ZB-65045B72-A. Used for automatic or manual transmissions. These came color keyed to your interior, add your desired color in the comments section of your online order. We will try to accommodate color requests where possible. We will select and ship what is available, these are easy to detail with the various vinyl paints available. These are used, and often the ashtrays will need...

Four required per car, used only on the driver side master power window switch, must have carbon fiber insulator in between the two plates.

A needed part for giving your car a tune-up.

A needed part for giving your car a tune-up.

This is a used windshield wiper delay governor, or module, and is a black box that mounts under the dash to the left of the radio. Sometimes called interval or delay wipers. *NOTE* Must be used in conjunction with a intermittent wiper switch.Part # D1ZB-17C476, D2ZB-17C476, MPC # D1ZZ-17C476-A.

Reproduction front tack strip for the front bow of the convertible top on the Mercury Cougar or Ford Mustang convertible. When replacing your convertible top, it's also a good idea to replace the tack strips in the front and rear bows of the convertible top frame. This strip slips into the front bow of the convertible top's frame and allows the fabric of the top to be attached to the frame. You will need approximately 5 feet (60 inches) of material and will have to trim the tack strip to fit...

Original used three piece tack strips for the 1969 - 1970 Cougar convertible. Over-sized, must be shipped via UPS.

Reproduction tack strip for the rear bow of the convertible top on the Mercury Cougar or Ford Mustang convertible. When replacing your convertible top, it's also a good idea to replace the tack strips in the front and rear bows of the convertible top frame. This strip slips into the rear bow of the convertible top's frame and allows the fabric of the top to be attached to the frame. You will need approximately 5 Feet (60 inches) of material and will have to trim to fit your top. You can also...

Complete four piece door vapor barrier kit specifically cut for the year of your Cougar. Check out the video on replacing your door panels below.

The decal I most often see on the 1971-1973 Cougar is the used one pictured here. Will be trying to locate this decal soon.

Currently, Convertible Tops dropshipped from this supplier will not ship for 4-6 weeks. The original tops would have been double texture PinPoint Vinyl. There are 3 different materials currently offered for these premium tops. Single Texture PinPoint Vinyl (GOOD): This is the material that is offered by almost all Mustang Vendors and it looks the same on the surface as an OEM top. This is a two-ply composite which has an outer layer of canvas-looking PVC vinyl plastic, and an inner layer of...

We have found a new manufacturer of the convertible top boots that are supposed to fit much better than the boots we were previously selling.  See Pics Below. Ford calls this part the "folding top dust hood". Made from original pattern. Features long lasting vinyl. Includes foam pads. We stock the black and white. All other colors are ordered on demand from the manufacturer. Please note that convertible boots never came from the factory with snaps, so any boot that comes with snaps is not...

Used to cushion and protect top vinyl from excessive wear from side rails. Replaces Ford part #: D1ZZ-7652875.

Retainer and screws used to retain the header seal.Fits:1971 Mercury Cougar1972 Mercury Cougar1973 Mercury Cougar1971 Ford Mustang1972 Ford Mustang1973 Ford Mustang

This is an inexpensive top that is only recommended if you car is going to be stored indoors. Have you ever wondered how a convertible top is installed, or maybe considered trying it yourself? Check out our in-depth installation video below! ...

We have found a new manufacturer of the convertible top boots that are supposed to fit much better than the boots we were previously selling. See Pics Below. Ford calls this part the "folding top dust hood". Made from original pattern. Features long lasting vinyl. Includes foam pads. We stock the black and white. All other colors are ordered on demand from the manufacturer. Please note that convertible boots never came from the factory with snaps (except the 6 on the interior panels), so any...

Replaces Ford Part #: D1ZZ-7650509-A

Replaces Ford Part #: D1ZZ-7650508-A

Driver side inner convertible top rail, made of cast aluminum. One of the most fragile parts on the convertible top assembly. Prone to failure when one of the hydraulic cylinders fails and the top assembly is forced. Comes bare as shown, be sure to save all of your installation hardware and bushings.Casting number on part reads: D1ZB-76631A09-A.

Passenger side inner convertible top rail, made of cast aluminum. One of the most fragile parts on the convertible top assembly. Prone to failure when one of the hydraulic cylinders fails and the top assembly is forced. Comes bars as shown, be sure to save all of your installation hardware and bushings. Casting number on part reads: D1ZB-76531A08-A.

Our well (or boot) liners fit correctly. Made of heavy duty, textured vinyl.

We have found a new manufacturer of the convertible top boots that are supposed to fit much better than the boots we were previously selling. See Pics Below. Ford calls this part the "folding top dust hood". Made from original pattern. Features long lasting vinyl. Includes foam pads. We stock the black and white. All other colors are ordered on demand from the manufacturer. Please note that convertible boots never came from the factory with snaps (except the 6 on the interior panels), so any...

We have found a new manufacturer of the convertible top boots that are supposed to fit much better than the boots we were previously selling. See Pics Below. Ford calls this part the "folding top dust hood". Made from original pattern. Features long lasting vinyl. Includes foam pads. We stock the black and white. All other colors are ordered on demand from the manufacturer. Please note that convertible boots never came from the factory with snaps (except the 6 on the interior panels), so any...

We have found a new manufacturer of the convertible top boots that are supposed to fit much better than the boots we were previously selling. See Pics Below. Ford calls this part the "folding top dust hood". Made from original pattern. Features long lasting vinyl. Includes foam pads. We stock the black and white. All other colors are ordered on demand from the manufacturer. Please note that convertible boots never came from the factory with snaps (except the 6 on the interior panels), so any...

We have found a new manufacturer of the convertible top boots that are supposed to fit much better than the boots we were previously selling. See Pics Below. Ford calls this part the "folding top dust hood". Made from original pattern. Features long lasting vinyl. Includes foam pads. We stock the black and white. All other colors are ordered on demand from the manufacturer. Please note that convertible boots never came from the factory with snaps (except the 6 on the interior panels), so any...

No excuses 100% complete mechanism with no cracks, missing parts or heavy corrosion. We can include the top cylinders but will not guarantee they will not leak. We carefully break this down by removing the header and crossbows and placing the original bolts back in the holes. Once you get this from UPS it will be very evident how it goes back together.

Reproduction Convertible Top Utica Plant Decal for the 1970 - 1973 Mercury Cougar or Ford Mustang 

C6AE-E Multiple applications over the years. 1. Later 1967 production cooling fan, generally used after 11/14/1966 on most 289 engine applications. 2. 1968 302 without air conditioning. 3. Mid year (after 11/6/1968) 1969 351 without air conditioning. 4. 1969 Early Boss 302 before 4/14/1969. 5. 1971 Cougar with 351 engine, without air conditioning. 6. **1973 Cougar 351-2V without air conditioning prior to 2/19/1973. Fan description - 4 blades and 17-1/2 inches in diameter. Ford master part...

D2OE-AA Applications: 1. 1972 Cougar with H code 351-2V engines - without air conditioning. 2. 1973 Cougar with H code 351-2V engine after 2/19/1973 - without air conditioning. May also be marked D2OE-AB. Fan description - 4 blades and 18-1/2 inches in diameter. Ford master part number D2OZ-8600-A. Check out this interesting video where they test the efficiency of factory style and aftermarket fans. Spoiler alert: the clutch fans are the most efficient! ...

D2OE-AB Applications: 1. 1972 Cougar with H code 351-2V engines - without air conditioning. 2. 1973 Cougar with H code 351-2V engine after 2/19/1973 - without air conditioning. May also be marked D2OE-AA. Fan description - 4 blades and 18-1/2 inches in diameter. Ford master part number D2OZ-8600-A. Check out this interesting video where they test the efficiency of factory style and aftermarket fans. Spoiler alert: the clutch fans are the most efficient! ...

D2SE-AA Applications: 1. 1972 and 1973 Cougar with H code 351-2V engines and air conditioning. 2. 1972 and 1973 Cougar with Q code 351-4V or 351CJ engines with or without air conditioning. Fan description - 5 blades and 18-1/2 inches in diameter. Ford master part number D2SZ-8600-A.Interesting Ford recall article for your reading enjoyment. Check out this interesting video where they test the efficiency of factory style and aftermarket fans. Spoiler alert: the clutch fans are the most...

Copper crush washer for all disc brake hoses and calipers 1968-73 Mercury Cougar and Ford cars like Mustang. Size 0.39" x 0.62" x 0.062". Four needed per car, two per side (one on each side of the disc brake hose end) sold indiividually.

Get your hands on the new, long awaited Mercury Cougar Eliminator book! Besides various specifics about "optional this" and "factory that", this book includes stories written by car owners. These stories remind us that our cars are more than just a collection of technical details. They link the cars directly to the people who own(ed) them. Why did they choose a Cougar and what impact did it have on their lives? Where did it come from and where is it now? Truly, the stories and history are the...

This Cougar II 1/25 scale factory sealed model kit was made by the Industro Motive Corp in Troy Michigan. This car was actually introduced in 1964 and was a Shelby Cobra based Ford- Cougar prototype vehicle that never made it into production.    Features: Retractable lightsWorking steeringOpening doorsOperating windowsPressure vent flapTubular frameChrome wire wheels260 cubic inch high performance engine ...

This marketing poster came from the C. Gayle Warnock collection which was liquidated on Ebay after his passing in 2007. Mr. Warnock was a Public Relations Executive for the Ford Motor Company, retiring in 1976. These NOS posters are the only known survivors.Measures 39" x 24"All edges are slightly worn from shelf life.

This marketing poster came from the C. Gayle Warnock collection which was liquidated on Ebay after his passing in 2007. Mr. Warnock was a Public Relations Executive for the Ford Motor Company, retiring in 1976. These NOS posters are the only known survivors.Measures 39" x 24"All edges are slightly worn from shelf life.

This marketing poster came from the C. Gayle Warnock collection which was liquidated on Ebay after his passing in 2007. Mr. Warnock was a Public Relations Executive for the Ford Motor Company, retiring in 1976. These NOS posters are the only known survivors.Measures 39" x 24"All edges are slightly worn from shelf life.

For the Cougar fan who has everything! This is a unique, awesome piece to hang on your wall. Made from laser-cut 18-gauge steel, rusted on the surface for a unique patina. Features a walking cat logo and COUGAR lettering. Measures 24" wide by 13" tall.We can also customize your sign for an extra $50 - such as your last name, business name, Joe's Garage, or whatever you'd like in lieu of "COUGAR", as long as we can make it fit (20 characters or less). Mention it in the order comments and we'll...