Exhaust

Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds.

Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds.

Concours reproduction horseshoe clamp with correct style of nuts. Used on all 1967 - 1973 models with 2 inch exhaust tips. Correct for XR7-G, GT-E, Mustang GT, Shelby Mustang, all Ford.   Clamp only, Sold individually. This is a Scott Fuller reproduction.

Concours reproduction with FoMoCo rectangular stamp and correct style of nuts. Used on all 1968 - 1971 models with 2-1/4" exhaust. Correct for Boss 302, Boss 429, Shelby Mustang, all Ford with 2-1/4 inch exhaust at the H - Pipe.  Clamp only, Sold individually. This is a Scott Fuller reproduction.

Concours reproduction with FoMoCo rectangular stamp. Used on all 1967 - 1973 models with 2" exhaust. Used on the rear section of the exhaust pipe next to the gas tank. Used in conjunction with tail pipe hangers. Clamp only, Sold individually. This is a Scott Fuller reproduction.

Concours reproduction with FoMoCo rectangular stamp. Used on all 1968 - 1973 models with 2-1/4" exhaust. Many of the stock exhaust systems were actually 2 inches. Most reproduction "Systems" are 2-1/4, use accordingly. Used on the rear section of the exhaust pipe next to the gas tank. Used in conjunction with tail pipe hangers. Clamp only, Sold individually. This is a Scott Fuller reproduction.

Exhaust pipe flange gasket, for use with stock cast iron exhaust manifolds. Cougar applications: all 289/302 engines 1967-69, 390 engines 1967-69, and 427-4V 1968 GT-E engine which uses 390 exhaust manifolds.Mustang and most all other Ford engines: 289/302 engines 1965-69, 390 engines 1967-69Fits between exhaust manifold and header pipe (H or Y pipe) steel construction, 2-1/32 inch inside diameter, tapered top and bottom, smooth inside. Sold individually, two required per car.These will work...

Exhaust pipe flange gasket, for use with stock cast iron exhaust manifolds. Fits all 351 Windsor engines 1969-70, 351C-2V  and 351C-4V (Cleveland) from 1970-73 Mercury Cougar and Ford Mustang.Fits between exhaust manifold and header pipe (H or Y pipe) 2-1/8 inch inside diameter, tapered top and bottom, smooth inside. Sold individually, two required per car.These will work with our reproduction H and Y pipes. Replaces Ford part number C8AZ-9450-B.

This 2-1/4 inch dual exhaust system is manufactured right here in the good old USA from original 1971 M code and 1972-73 Q code Cougars equipped with the 351C engine. This direct replacement system includes: 1 H pipe, 2 intermediate pipes, 2 mufflers, and a right and left tail pipe. The system is constructed from 2-1/4 inch aluminized piping and features blue printed bends with everything being replicated as close as possible to the original. The mufflers in the system have the hanging...

Very nice reproduction of the drivers side muffler hanger as found on 1970 - 1973 Mercury Cougar and Ford Mustang. Every thing looks correct, riveted rubber and stamped steel brackets as original. You can hang up to a 3 inch pipe with this unit.

Reproduction OEM style passenger side (right hand) exhaust hanger for the Mercury Cougar or Ford Mustang. You can hang up to a 3 inch diameter pipe with this unit.

D1ZE-9431-AA or D3AE-9431-AA (for 1973) 351-2V Cleveland factory original cast iron exhaust manifold for driver side. *351C-2V exhaust manifolds only match up to factory 2V intake manifold ports and some aftermarket aluminum cylinder heads, such as one offered by Edelbrock.

D3AE-9431-AA (for 1973) 351-2V Cleveland factory original cast iron exhaust manifold for driver side. Same casting as D1ZE-9431-AA used 1971-72ish.*351C-2V exhaust manifolds only match up to factory 2V intake manifold ports and some aftermarket aluminum cylinder heads, such as one offered by Edelbrock.

Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds.

This direct replacement is the 2-1/4 inch H pipe only and is for any 1971-73 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2-1/4 inch aluminized pipes and made from an original 1971 Cougar and Mustang with either the H, M, or Q code 351C engine. We also sell OEM style dual exhaust systems that include the H pipe, mufflers, and tail pipes.*NOTE* Will not fit 351 Windsor, 1970 351 Cleveland engines. Please...

1971 *351-4V prior to 4-12-1971. 1972 and 1973 351-4V with "Quiet" dual exhaust. Holds the rear of the muffler to the underside body. Ford part number D1WY-5260-B. *Early production prior to 4-12-1971.

Shopping list of applications. For all H code 351-2V engine codes with singles exhaust. 1971 *351-4V prior to 4-12-1971. 1972 and 1973 with "Quiet" dual exhaust. Engine designated as a 351-4V on air cleaner lid. Holds the rear of the muffler to the underside body. Ford part number D1WY-5260-A. *Early production prior to 4-12-1971.

1971 *351-4V after 4-12-1971. 1971 429 CJ 1972 with "Sporty" dual exhaust. Engine designated as a 351-CJ on air cleaner lid. Holds the rear of the muffler to the underside body. Ford part number D1WY-5260-C. *Late production - after April 12, 1971.

Mounts to the frame on the left side of the fuel tank. Supports and holds the rear of the tailpipe stationary. 1971 all 351 and 429CJ with dual exhaust. 1972 all 351 with "Quiet" and "Sporty" dual exhaust. Ford part number D1ZZ-5260-E. *Pipe clamp D1AZ-5A231-C needed 2" diameter pipe "Quiet". *Pipe clamp D1AZ-5A231-A needed 2-1/4" diameter pipe "Sporty".

Mounts to the frame on the right side of the fuel tank. Supports and holds the rear of the tailpipe stationary. 1971 351-2V single exhaust. 1971 351-4V and 429CJ. 1972 351-CJ with "Sporty" dual exhaust. Ford part Number D1ZZ-5260-A.

Mounts to the frame on the right side of the fuel tank. Supports and holds the rear of the tailpipe stationary. 1972 1973 351-2V single exhaust. 1971 351-4V and 429CJ. 1972 1973 351-4V with "Quiet" dual exhaust. Ford part number D1ZZ-5260-B. *Pipe clamp D1AZ-5A231-C needed 2" diameter pipe "Quiet".

Muffler mounting tabs for using factory Ford muffler hangers on aftermarket turbo style exhaust mufflers. These help achieve that concours look using a replacement muffler or mufflers. We recommend using your existing horse shoe shaped muffler hanger as a jig for locating these tabs prior to welding. These were copied from the original style tabs found on most 1968-73 Mercury Cougar and Ford Mustangs. 1967 cars and some Mustangs used a single transverse muffler behind the rear axles, these may...

Reproduction hex screw for exhaust pipe clamps for the 1967 - 1973 Mercury Cougar and Ford Mustang. 5/16 x 1-1/2 screw. Fits original and new clamps.

Reproduction exhaust pipe to exhaust manifold nut for the Mercury Cougar or Ford Mustang and they are sold individually.Ford part # 376420-S.

Reproduction Exhaust Manifold Pipe Stud Kit for the 260, 289, 302, 351 and 1969 390GT 1967 - 1972 Mercury Cougar and Ford Mustang

Kit has the longer studs for use with spacers or butterfly spacers, between 390 and 428CJ passenger side exhaust manifolds and H pipe flange.

This 2-1/4 inch rear segment exhaust system is manufactured right here in the good old USA from an original 1971 M code Cougar with the 351C engine. This direct replacement system includes: 2 intermediate pipes, 2 mufflers, and a right and left tail pipe. The system is constructed from 2-1/4 inch aluminized piping and features blue printed bends with everything being replicated as close as possible to the original. The mufflers in the system have the hanging tabs attached so that they...

Air cleaner pre-heater paper hose. Should fit most applications from 1970-73 Mercury Cougar and Ford Mustang with V8 engines. 2 inch inside diameter, we cut these to about 9 inches long. Correct black paper outside, flexible paper tube, kind of like a Slinky. Please verify your needed length, we leave them a bit longer than needed so that they fit more than one application.

OEM Style Universal Exhaust Hanger Bracket 1967, 1968, 1969, 1970, 1971, 1972 and 1973 Mercury Cougar and Ford Mustang

This direct replacement is the 2 inch Y pipe only with 2-1/4 intermediate pipe outlets and is for any 1971-73 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2 inch aluminized pipes and made from an original 1971 Cougar and Mustang with the 351C 2V engine. We also sell OEM style dual exhaust systems that include the H pipe, mufflers, and tail pipes.*NOTE* Will not fit 1970 351 Cleveland engines. Please...

Yoke style factory exhaust pipe clamp. For 2 inch outside diameter exhaust pipes. Two piece clamp see picture Ford part number D1AZ-5A231-C.

Yoke style factory exhaust pipe clamp. For 2-1/4 inch outside diameter exhaust pipes. Two piece clamp see picture Ford part number D1AZ-5A231-A.

D2OE-9430-BA 351-2V Cleveland engine, factory original cast iron exhaust manifold for passenger side. *351C-2V exhaust manifolds only match up to factory 2V intake manifold ports and some after market aluminum intakes such as one offered by Edelbrock.

D1ZE-9431-B 351-4V Cleveland factory original cast iron exhaust manifold for driver side. At some point there may have been a D1ZE-9431-BA casting number used, which may be substituted as per the Master Parts Catalog. *351C-4V exhaust manifolds only match up to factory 4V intake manifold ports and some aftermarket aluminum intakes such as offered by Weiand and Edelbrock.

D0AE-9430-B 351-4V Cleveland factory original cast iron exhaust manifold for passenger side. At some point there may have been a D0AE-9430-G casting number used, which may be substituted as per the Master Parts Catalog. Same manifold 1970-1973. *351C-4V exhaust manifolds only match up to factory 4V intake manifold ports and some aftermarket aluminum intakes such as offered by Weiand and Edelbrock.

351-2V Cleveland, factory cast iron 2V exhaust manifold set, both correct right D2OE-9430-BA and left D1ZE-9431-AA or D3AE-9431-AA side matching exhaust manifolds.

351-4V Cleveland factory cast iron 4V exhaust manifold set, both correct right and left set of matching exhaust manifolds. Manifolds the same 1971-1973.

1971 *351-4V after 4-12-1971. 1971 429 CJ. 1972 with "Sporty" dual exhaust. Engine designated as a 351-CJ on air cleaner lid. Holds the rear of the muffler to the underside body. Ford part number D1WY-5260-D. *Late production - after April 12, 1971.

Ford part number D2AZ-9A603-D (outer section) and D2AZ-9A603-B (inner section) make up this two piece metal shroud for all 1972 - 1973 H code 351-2V engines. The outer shield section is common to both 2V and 4V 1972 - 1973 351c engines but the inner is unique to the 2V.

Ford part number D2AZ-9A603-D (outer section) and Ford part number D2AZ-9A603-C (inner section) make up this two piece shroud for the 1972 - 1973 Q code 351-4V engine. This inner shield conforms to the 351-4V cast iron exhaust manifold only and the outer portion fits both the 2V and 4V.