Your cart is empty!
If you have cookies enabled and have added an item to your cart, but you are still seeing this message, that could indicate that the cookie for our shopping cart is corrupted on your computer.You should be able to fix this by either:
Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds.
Backup light switch retainer for Hurst shifters as installed on 1970-73 Mercury Cougar, Ford Mustang, and most vintage Ford cars with factory installed Hurst shifters.
Reproduction A/C Tag Retainer for the 1967 - 1973 Mercury Cougar
Molded rubber plug, seals access hole in the side of shift housing. Replaces Ford Part # : C5ZZ-7C147-B Check out our video on rebuilding your shifter below: ...
Floor shifter access plug. 1967-73 Mercury Cougar and Ford Mustang, also fits floor shift 1971+ Mercury Comet and Ford Maverick. Ford Part number C7ZZ-7C147-A. Check out our video on rebuilding your shifter below: ...
Reproduction Alternator Pulley Nut for the 1967 - 1973 Mercury Cougar - 1967 - 1973 Ford MustangSold individually
D2OZ-7976-A Aluminum bell housing, sometimes called a converter housing in the Ford shop manual. 1972 - 1973 Mercury Cougar and Ford Mustang with 351 engine and automatic FMX transmission, code X on your door data plate tag. Ford master part number D2OZ-7976-A.
Correct for 1971, 1972 and 1973 only. 351-2V and 351-4V engines , including Boss 351 for 1971 - 73. Ford part number D1TZ-6392-A and D1TZ-6392-C. Shipped bare, no hardware or clutch fork.
These Spark Plug Wire Separators are made of high-quality ABS plastic. Constructed to hold both standard 7mm and 8mm high-performance spark plug wires. Fits directly on valve cover clip. Available in blue, red and OE black.
Used bolt and washer for attaching the crankshaft balancer or damper to the crank shaft. 15/16 inch hex head with 5/8-18 threads and 1.75 inches long. Basically fits all Mercury Cougar engines except the 1971 429 Cobra Jets engines. Fits 1967-73 289, 302, Boss 302, 351W, 351C, 390, 427, and 428CJ engines.Torque specifications for this bolt are 70-90 foot pounds.*Note does not fit 429 or 460 V8 engines or any 6 cylinder engines.
Reproduction AC Compressor Clutch Bolt for the 1967 - 1973 Mercury Cougar - 1967 - 1973 Ford MustangSold individually
Zinc (dark silver)
Bolts and installation kit for most 1970-73 Mercury Cougar and Ford anything, including Mustang with V-8 engines. Kit includes main pivot bolt and adjusting bolt as shown. Spacer not included, but available used.
Phosphate & Oil (gay-black)
Four of these bolts are used to secure the isolator portion of the engine mounts to the 289/302/351 blocks. Includes 351W and 351C engines. 5/8" hex head bolt. Sold individually Concours phosphate & Oil (gray-black).
Used on all small block engines to attach the timing pointer to the timing cover. 1967 - 1973 V-8 engines 289, 302, & 351.
Replaces Ford part # 385664-S
Replaces Ford part # 378172-S
part # 56131-S
Reproduction 351W Intake Manifold Bolt for the 1969 - 1973 Mercury Cougar - 1969 - 1973 Ford MustangSold individually
Phosphate & Oil finish. Sold individually. Replaces Ford part #: 378782-S
This is longer of the two with the + on the bolt head.
This is the shorter version of the top-loader with no "+" on the head.
New valve cover bolts for all Boss 302, 351C-2V, and 351C-4V Ford engines. These are the AMK bolts with original style Ford assembly line head markings. Correct 7/16 hex head and split tooth captured washer, sold in sets of 16.*Note - Excludes 289/302 and 351W engines (see part number 8316)Replaces Ford part number 373071-S.
Reproduction bolts and washers for the automatic transmission bell housing on any 1971 - 73 Cougar or Mustang equipped with a 351 engines and C-6 transmissions. Bell housing to engine block bolts. Fits most all other Ford small block V-8's from 1971-73.
Set of 6 new correct bolts for attaching the FMX transmission to 351 engines. Fits all 1967-73 Mercury Cougar and 1967-73 Ford and Mustang with transmission code X, or FMX automatic transmissions. Quality fasteners from AMK.
Reproduction bolts and washers for the manual transmission bell housing on any 1969 - 73 Cougar or Mustang equipped with a 302 / 351 engines and either 3 or 4 speed manual stick shift transmissions. Bell housing to engine block bolts. Fits most all other Ford small block V-8's from 1969-73.
Four of these bolts are used to secure the isolator portion of the engine mounts to the 289/302/351 blocks. Includes 351W and 351C engines. 5/8" hex head bolt. Sold as a set of 4. Concours phosphate & Oil (gray-black).
Bolts for securing the inspection cover for small block C-6 automatic transmissions 1971-73 Mercury Cougar or Ford Mustang. Not sure why 3 bolts, but one is different.
Pair (2) Bolts for securing the inspection cover for any C-4 automatic transmission 1967-68 Mercury Cougar or 1965-70 Ford Mustang. Additionally also fits FMX transmissions 1969-73 Mercury Cougar.or Ford Mustang.
4 Bolts for securing the inspection cover for any C-6 automatic transmission 1967-70 Mercury Cougar or Ford Mustang.
Set of new bolts for attaching the floor shift bucket to the hump in the floor board, 1/4-20 bolts with washer head and 3/8 inch hex head. Sold as a set of 4 bolts. Fits all 1967 - 1973 Mercury Cougar and Ford Mustangs, and likely all of other floor shift Ford products from this time period. Check out our video on rebuilding your shifter below: ...
This bracket connects the battery hold down clamp to the fender apron to stop the battery from rocking from side to side. Most cars are missing this crucial part to stabilize the battery. Replaces Ford Part #: D0OZ-10757-A.
Replacement rubber bushing for repairing any automatic shift arms on any 1967-73 Mercury Cougar or Ford Mustang, and most Fords with automatic floor shift levers. Fits arms with 3/4 inch lower holes for attaching transmission shift rods. Replaces Ford part number C7ZZ-7343 Check out our video on rebuilding your shifter below: ...
This kit is for the clutch equalizer or clutch Z-bar on 1971-73 Mercury Cougars or Ford Mustangs, all V8 engines. All parts included as shown. *Tip - Add a liberal amount of grease to these parts during installation.
These reproduction brake and clutch pedal bushings are made from high strength plastic that is wear resistant. Two are required for automatic cars, four for manual transmission cars. Sold as a pair. Replaces Ford part # B7AZ-2471-A.
(7526) Nylon plastic injected. Correct original design. Protects clutch equalizer and rod, and removes excess play. These are to put on either end of your clutch pedal rod. Sold individually. If your going to do both ends you will need to order 2 of these.Replaces Ford Part #: C0AZ-7526-B.Customer review: Called WCCC the other day after calling around to a lot of garages and auto parts stores trying to find out the torq specs for my rocker arms on my Cougar. I wanted to check to make sure they...
Internal tail shaft assembly from a C4 transmission. We only disassemble up to what you see in the picture. *Excludes later versions of C4 transmission that have thicker output shafts.
Internal tail shaft assembly from a C-6 transmission. We only disassemble up to what you see in the picture.
Replaces Ford part # 351089-S
Zinc (dark silver) finish
Used transmission line adapter and check valve for all FMX transmissions. This fitting goes into the rear part of the transmission case and connects the rear most cooling line to the case. Has internal ball check valve to prevent fluid from back flowing. All FMX transmissions 1969-73 Mercury Cougar or Ford Mustang. The male threads going into the transmission case are 1/2-20 pipe threads.Replaces Ford part number C3AZ-7D174-A.
Pair or reproduction clips used to hold your transmission cooling lines together and keeps them from rattling.
Adjusting rod - Lower clutch rod that fits between the Z-bar and the clutch fork. Replaces Ford Part # C8AZ-7521-B THIS FITS: 1971 1972 1973 MUSTANG 6 CYLINDER 302 351C BOSS 351 1971 MUSTANG 429CJ 429SCJ 1972 1973 1974TORINO351C 351 CJ 1968 1969 1970 1971GALAXIE 6 CYLINDER 302 351 390 429 1968 1969 1970 1971 MERCURY FULL SIZE351 390 429 1971 COUGAR429CJ 429SCJ 1971 1972 1973COUGAR 351C 351CJ 1972 MONTEGO6 AND 8 CYLINDER
Clutch equalizer pivot mount, engine side. Fits all 1971 - 1973 Mercury Cougar with 351 Cleveland engine, and 1971 - 1973 Ford Mustangs with 302 or 351 Cleveland engine. Replaces Ford part #: D1ZZ-7A572-A.
Clutch Fork Pivot for Cougars manufactured after 2/16/1968. Replaces Ford Part #: C8AZ-7522-A.