Contact Us / Visit Us (click here)
If the Shopping Cart takes too long to respond, you can bypass the shopping cart and go straight to the checkout page by clicking the following link: Checkout.
International Customers Click Here [Updated 1/2024]
Loading Trivia . . .

Search This Category:
Select layout:
Products (Click sub-categories above to ONLY display results for that Sub-Category) 2353-2400 of 3532
Price: $7.45

Buy Details

Availability: In-Stock Item
Item #: 14-0019 -

New spray silicone lubricant for the squeaky Mercury or Ford. This spray lubricant is great for door hinges, trunk hinges, hood hinges and basically anything else that needs to be lubricated. Easy to use and will definitely de-squeak your vehicle.

MSRP:$3.99
Price: $0.85

Buy Details

Availability: In-Stock Item
Item #: 32395 -

New slotted pan head screw for mounting distributor points or condensers. Three total, per single advance Ford distributors. We know that these fit FoMoCo, Autolite and Motorcraft marked distributors 1967-73. These are AMK screws 8-32x9/32". Sold individually, but you likely need 3. 

Price: $1.05

Buy Details

Availability: In-Stock Item
Item #: 32396 -

New slotted pan head screw for mounting distributor vacuum advances. Two total, per Ford distributor. We know that these fit FoMoCo, Autolite and Motorcraft marked distributors 1967-73. These are AMK screws 8-32x1". These are phosphate dipped. Sold individually, but you likely need 2. 

Price: $2.88

Buy Details

Availability: In-Stock Item
Item #: 15-0178 -

Used snap ring that is used to hold the bearing on you the steering shaft. This ring was used on 67 - 78 fixed columns and 70 - 78 tilt columns. Not for use on 67 - 69 tilt columns.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Price: $1,695.85

Buy Details

Availability: Ships Direct from Supplier (Except International)
Item #: 32128 -

Reproduction black Holley "Sniper" fuel injection conversion carburetor for the 67 - 73 Cougar or Mustang. Upgraded Sniper II also now available! Dual Pattern bolt on carburetor replacement, designed to fit 4150 Flange & Spread Bore manifolds - (Spread Bore Sealing Plate Part #9006 is recommended)Throttle body mounted ECU – no extra boxes to mountSupports up to 650hp with Four 100 Lb/Hr InjectorsOnly 4 Wiring Connections Required! (Battery +, Battery - , Switched Ignition & RPM)Includes...

Price: $1,795.85

Buy Details

Availability: Ships Direct from Supplier (Except International)
Item #: 33548 -

The #1 EFI conversion system just got better! Introducing Sniper 2 EFI - a self-tuning, easy-to-install, EFI conversion for common 4-barrel (4150 flange) style carburetors. Holley took everything that they learned from the original Sniper EFI system and added 14 new features that will make your EFI conversion more simple, reliable, and modern. Like all Sniper EFI systems, Sniper 2 is designed to work with the Sniper Ecosystem that includes Hyperspark ignition, complete fuel systems, multiple...

Price: $72.86

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 25486 -

IMCO emissions air cleaner snorkel for a 1972 Cougar with 351-2V engines only. Non-California, 49 states only. (California required IMCO with NOx, see D2ZZ-9A626-B). Ford part number D20Z-9A626-C.

Price: $94.86

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 25252 -

Application is for all 1971 Cougars with 351 engines, both 2V and 4V engines. Additionally it includes 1972 351-4V without NOx. Our research shows that NOx was a California emissions requirement. Ford part number D10Z-9A626-B. *Note - 1972 49 state 351-4V air cleaner snorkel.

Price: $138.87

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 25547 -

California emissions 351-4V air cleaner snorkel. DSO 52 and DSO 53 Cougars with Q-code 351-4V engines.

Price: $19.98

Buy Details

Availability: In-Stock Item
Item #: 10714 -

Air cleaner pre-heater paper hose. Should fit most applications from 1970-73 Mercury Cougar and Ford Mustang with V8 engines. 2 inch inside diameter, we cut these to about 9 inches long. Correct black paper outside, flexible paper tube, kind of like a Slinky. Please verify your needed length, we leave them a bit longer than needed so that they fit more than one application.

Socket - Clutch Equalizer - PAIR - Repro ~ 1971 - 1973 Mercury Cougar / 1971 - 1973 Ford Mustang
1965 - 1971 Ford Galaxie and Full Size (Galaxie, XL, LTD, Custom 500 etc..)| 1970 Torino 429|1972 - 1976 Ford Torino, Gran Torino and Ranchero |1973 - 1976 Ford Maverick
0
Price: $22.75

Buy Details

Availability: In-Stock Item
Item #: 14065 -

Replacement pair of Clutch Equalizer Bar ( Z-Bar) Bushings. These are for manual transmission equipped models and are a bushing that is no longer available from Ford. These are the split bushing style that replace Ford part number C5AZ-7543-C. These fit 1965 1966 1967 1968 1969 1970 1971 Ford Galaxie and Full Size Models (Galaxie, XL, LTD, Custom 500 etc..), 1970 Torino 429 Models, 1971 1972 1973 Mustang, 1972 1973 1974 1975 1976 Ford Torino, Gran Torino and Ranchero models and 1973...

Price: $4.28

Buy Details

Availability: In-Stock Item
Item #: 41606 -

Fits both front and rear marker light sockets. Four per vehicle. These are made so that you can splice into your harness. These solve the corroded socket and intermittent light problem.These fit the side marker lights as well as the instrument panel lights. We highly recommend converting these over to LED.Replaces Ford Part #: D0DZ-15434

Price: $176.75

Buy Details

Availability: In-Stock Item
Item #: 12135 -

This new version sequential box works with either standard or plasma LED bulbs NOTE: Although your existing emergency flasher might work just fine with the new sequential unit, it is highly recommended that you also use the same updated electronic sequential flasher in its place to guarantee proper operation. This is a direct fit replacement, just pop open your black plastic box located in the driver side trunk drop off and plug it in. Your January 1970 and newer Cougar will have...

MSRP:$90.99
Price: $74.65

Buy Details

Availability: In-Stock Item
Item #: 25672 -

This is the exact same cut of sound deadener as the tar based sound deadener, but cut out of the foil heat shield rather than the paper backed tar. The foil heat shield weighs over 20 Lbs less than the paper backed tar when cut into the same pattern. This makes shipping this over seas much more affordable than the paper backed tar version of the underlayment kit.For a super cheap version of this insulation, try this item: foil insulation ...

Price: $62.05

Buy Details

Availability: In-Stock Item
Item #: 11842 -

5/16" thick sound deadening and heat reflecting material, comes in a 4' X 6' sheet that can be cut to fit. This insulation consists of two layers of polyethylene bubble film sandwiched between two layers of aluminum foil. Temperature range rated -60 deg. F. to 180 deg. F. Combining this with the tar-based sound deadener underlayment will result in similar sound deadening as the OEM sound deadener.Below is listed how many rolls you will need to underlay the sections of a Cougar:  Area...

Price: $173.95

Buy Details

Availability: In-Stock Item
Item #: 14538 -

Reproduction 7 Piece sound deadener underlay for the the 71 - 73 Convertible Cougar.

Price: $174.15

Buy Details

Availability: In-Stock Item
Item #: 14540 -

Reproduction 5 piece sound deadener underlay for the 71 - 73 Cougar Coupe

Price: $94.45

Buy Details

Availability: Ships Direct from Supplier (Except International)
Item #: 14537 -

This is the same kit everyone else is offering, but if what you are looking for is a kit that fits and performs as good or better than the original... What you get when you order this kit is rather disappointing. For years we have not sold any underlay kits at all, we have just suggested you get your dose of disappointment closer to home and save the shipping costs or visit your local stereo store and see what high tech "cut to suit" materials they offer. Well, at least this listing will give...

MSRP:$71.99
Price: $45.85

Buy Details

Availability: Ships Direct from Supplier (Except International)
Item #: 14539 -

This is the same sound deadener kit that everyone else is offering, but if what you are looking for is a kit that fits and performs as good or better than the original... What you get when you order this kit is rather disappointing. For years we have not sold any underlay kits at all, we have just suggested you get your dose of disappointment closer to home and save the shipping costs or visit your local stereo store and see what high tech "cut to suit" materials they offer. Well, at least...

Price: $65.55

Buy Details

Availability: In-Stock Item
Item #: 25937 -

This aluminum backed, tar sound deadener with adhesive is approximately 1/16 of an inch thick and works well behind door panels, at the firewall and under the headliner as a sound, heat and vapor barrier. One sheet required per door. Cut to fit, then remove paper backing to reveal adhesive, and stick in place. Comes in a 36 inch tall by 50 inch wide roll. *NOTE* Use caution when working with this product. The thin sheet of aluminum is quite sharp. We highly recommend using gloves. Before...

Price: $98.85

Buy Details

Availability: In-Stock Item
Item #: 12174 -

HushMat sound deadening and thermal insulation enhances your firewall with the easiest to install sound deadening material. Your vehicle is fun to drive, but the engine gets hot. There is over 200 degrees of heat cooking your firewall and floor pan. Your engine, headers, manifold and exhaust generate tremendous heat that transfers to the metal firewall and floor and this heats up your vehicle interior. It can create a very uncomfortable ride, especially in the summer. This also forces your AC...

Price: $199.85

Buy Details

Availability: Discontinued
Item #: 12320 -

HushMat sound deadening and thermal insulation enhances your firewall with the easiest to install sound deadening material. Your vehicle is fun to drive, but the engine gets hot. There is over 200 degrees of heat cooking your firewall and floor pan. Your engine, headers, manifold and exhaust generate tremendous heat that transfers to the metal firewall and floor and this heats up your vehicle interior. It can create a very uncomfortable ride, especially in the summer. This also forces your AC...

Price: $25.88

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 25070 -

Alternator spacer bracket for all 351 engines. 1970-73 Mercury Cougar and Ford Mustang among others such as Torino, Cyclone, Galaxie, LTD, etc. Aluminum material, 2-1/4 inches long, with a 7/16" hole. Sometimes solid and sometimes open along the side. Ford part number D0OZ-10A370-A.

Price: $2.88

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 11907 -

Used alternator fan spacer for the 1967 - 1973 Mercury Cougar or Ford Mustang.  This spacer also fits many other Ford applications.  Ford part number: C5AZ-10A344-B.

Price: $14.85

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 33563 -

Fuel tank spacer. Welds to the bottom side of the trunk pan. Spaces the tank, so that the fuel vapor separator assembly, isn't pinched. Easy to make these stands, and there are two needed, are approximately 1-1/2 inches tall. Strap is 1-1/8 inches wide.  

Price: $9.86

Buy Details

Availability: In-Stock Item
Item #: 14-1037 -

Used spacer that fits inside your seat belt buckle and serves as a stop for when you assemble the metal buckle into the face plate/bezel. Installation is as shown in the pictures above.  Sold individually, one per buckle.

Price: $11.45

Buy Details

Availability: In-Stock Item
Item #: 30498 -

Reproduction 384543-S8 Power steering pump adjusting spacer for use without air conditioning. For most 1970 - 1973 Mercury Cougar or Ford Mustang with 351C engines. Spacer dimensions: 7/16" I.D. and 1/2" thick.*Note 1970 and later cars with 302 or 351W engines use a 3/4 inch spacer.

Price: $16.07

Buy Details

Availability: In-Stock Item
Item #: 11-0417 -

Replacement disc brake pedal mounting spacer. Correct diameter and length for installing disc brake pedals 1967-73 Mercury Cougar and Ford Mustang. About 2-1/8 inches long, correct I.D. and O.D. made from Moly steel. Basic Ford part number 2A188, the correct Mustang / Cougar number has been obsolete in the Ford MPC's for years.

Price: $6.89

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 23774 -

One per side, 1968 does not use the triangle markings. The letter "D" stamping was in place to aid line workers with correct placement on the car.

Price: $92.57

Buy Details

Availability: In-Stock Item
Item #: 26053 -

Reproduction engine block spacer plate for 69 - 73 Cougars or Mustangs with 351 engines and 3 or 4 speed manual transmissions. According to the Master Parts Catalog, it also fits 164 tooth bellhousings on 1968-70 with 302 engines too. We also stock the early version from 1968 and 157 tooth versions.

Price: $17.87

Buy Details

Availability: Discontinued
Item #: 15318 -

This spring does NOT have correct spring finish or tension, but will work fine if you want to save a few $$$. Above is a comparison to this reproduction which is carried by other retailers, compared to our spring which is very close to the correct finish, length, and tension. Replaces Ford Part # : C8ZZ-17119-A ...

Price: $995.04

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 22230 -

Original space saver tire marked F78-14 B.F. Goodrich, from a 1970's Mercury or Ford. These were optional in 1968-73. It has the smaller hub size and single valve stem. Never inflated condition. One RARE unit! Just looking for a space saver spare? We have much lower priced space savers with different sized / marked tires, and some with dual valve stems from the 1970's. Please inquire. *NOTE* Does not include inflator bottle and valve caps are usually missing. ...

Price: $83.65

Buy Details

Availability: In-Stock Item
Item #: 26761 -

These were never offered originally but are a popular accessory and more cost efficient than buying a replacement for that unsightly old wheel and tire you took from a Granada in the bone yard! Only the 71-73 came with the speckled pattern.

Price: $87.95

Buy Details

Availability: In-Stock Item
Item #: 26759 -

These were never offered originally but are a popular accessory and more cost efficient than buying a replacement for that unsightly old wheel and tire you took from a Granada in the bone yard! Only the 71-73 came with the speckled pattern.

Price: $16.75

Buy Details

Availability: In-Stock Item
Item #: 20551 -

10 5/8" Spare Tire Mounting Bolt. Not 100% correct, but close replacement for the 1969 - 1973 with the 10 3/4" spare tire mounting bolt. Replaces Ford Part #: C8ZZ-1448-A, D0ZZ-1448-A & D1ZZ-1448-A.

Price: $3.16

Buy Details

Availability: In-Stock Item
Item #: 13890 -

Correct Autolite 24 spark plugs for all 1970-73 351 Cleveland engines. This is what Ford installed originally from the factory. Typically these should have a electrode gap of 0.035", with either stock points or Pertronix ignition systems. Sold individually.

Price: $2.85

Buy Details

Availability: In-Stock Item
Item #: 13863 -

Correct Autolite 45 spark plugs for all 1967-73 289/302/351W/390/428CJ engines. This is what Ford installed originally from the factory. BF32 crosses over to this spark plug. Typically these should have a electrode gap of 0.035", with either stock points or Pertronix ignition systems. Sold individually.

Price: $17.42

Buy Details

Availability: In-Stock Item
Item #: 42059 -

These Spark Plug Wire Separators are made of high-quality ABS plastic. Constructed to hold both standard 7mm and 8mm high-performance spark plug wires. Fits directly on valve cover clip. Available in blue, red and OE black.

Price: $54.86

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 27488 -

Not sure of the exact application for these original Ford stereo speaker wiring harnesses. We think that they may have come from the radio kits installed by Ford and Mercury dealers. Note the special speaker connector plugs. The individual right and left speaker wiring leads are about 40 inches in length from the center plug that goes to the radio or stereo. The paper tags are missing from these harnesses, but we are pretty sure that they begin with C8OA-19A041.One of our customers says that...

Price: $1.45

Buy Details

Availability: In-Stock Item
Item #: 26595 -

This correct replacement speedometer cable firewall grommet is manufactured using the original Ford blueprints and is a direct replacement for the factory grommet. Replaces Ford part number 380634-S.

Price: $8.25

Buy Details

Availability: In-Stock Item
Item #: 14345 -

Made out of Nylon. Please confirm teeth count and direction of teeth. Color codes do not guarantee direct replacement. 4 speed Toploaders have reversed tooth direction. Click here to use our Speedometer Gear Calculator. Available in 16, 17, 18, 19, 20, 21, and 23 tooth*. Replaces Ford Part: C0DZ-17271-A, C0DZ-17271-B, C0DZ-17271-C, C0DZ-17271-D, C0DD-17271-A, C1DZ-17271-A * - 23 tooth gears are not a Ford part and only have a life expectancy of 25,000 miles. They also have been reported to...

Price: $8.25

Buy Details

Availability: In-Stock Item
Item #: 12156 -

These four speed gears have the teeth reversed from the direction of the automatic gears. Made from Nylon. These gears only fit the 4 speed Toploaders. Click here to use our Speedometer Gear Calculator.   Replaces Ford Part # : C2DZ-17271-G 20 Tooth Gear Pictured