1972 Mercury Cougar

Good used Western part that is not bent or heavily rusted and the left is the same as right. Ford master part # D1WY-16B134-A.

Hook bracket weld in retainer for the rear seat installation on any 1971-73 Mercury Cougar. This is the front bracket that holds in the rear seat and was used on both coupes and convertibles. Sold individually, two required per car. We cut out a section of the floor under the rear seat as shown. Make good measurements prior to removal of your old brackets.  The Ford number is C9AZ-6263370-A.

New Old Stock. This part is located in the right front corner of the panel and has to be rotated inward to remove it from the guide rail so the panel cannot be removed. Imprinted on the plastic portion of the part is a Golde part number 100 414 645. Ford part number C8WY-65502L08-A

This part is located in the right front corner of the panel and has to be rotated inward to remove it from the guide rail so the panel cannot be removed. Imprinted on the plastic portion of the part is a Golde part number 100 414 645. Ford part number C8WY-65502L08-A

72 - 73 Mercury Cougar and Ford Mustang Front Drum Intermediate Brake Line made of OE-style steel. Intermediate Brake Lines are the lines running from the front of the car to the back feeding your rear brakes. These lines will run along your chassis all the way back to the rear brake drop hose. All lines come Pre-Bent and flared with the correct threaded fittings which reduces your install time tremendously. These mild steel lines are Galphan coated for added protection. ...

This filter fits all V8 Mercury Cougars or Ford Mustangs with the Autolite Carburetor. This filter fits all 1967 - 1973 Cougars except for the following: the Boss 302 4V, 390 4V, 427 4V, 428 4V and the 429 4V. Will also fit many 6 cyl Mustang applications. These Filters are precisely designed and engineered to meet OEM requirements and fitment. Delivering high efficiency filtration, our filters meet modern engine demands for maximum fuel flow. Prevents harmful contaminants such as dirt,...

Reproduction OE steel one piece fuel pump return line with 5/16" fittings for the Mercury Cougar. *NOTE* All of our tank to pump fuel lines come "gently" folded over to be shipped.  When you receive your fuel line, you will have to straighten it out. It is a fairly straight forward procedure and we have not had anyone struggle with this to date.

This is the steel tube that goes from the carburetor to the fuel pump.

This is the steel tube that goes from the carburetor to the fuel pump.

This is the steel tube that goes from the carburetor to the fuel pump. Available in original steel or stainless steel.

This is the OE steel tubing the goes from the fuel pump to the carburetor.

This is the stainless steel tube that goes from the carburetor to the fuel pump. Available in original steel or stainless steel.

Reproduction fuel line for the Boss 351 engine. Bent for use with factory intake manifolds, OEM fuel pump, and OEM installed Holley carburetor.Can be carefully bent to fit most applications where replacement fuel pumps or Holley 4150 carburetors are used.

Reproduction OE steel two piece fuel tank to pump fuel line for the Mercury Cougar.*NOTE* All of our tank to pump fuel lines come "gently" folded over to be shipped.  When you receive your fuel line, you will have to straighten it out. It is a fairly straight forward procedure and we have not had anyone struggle with this to date.

Reproduction stainless steel two piece fuel tank to pump fuel line for the Mercury Cougar.*NOTE* All of our tank to pump fuel lines come "gently" folded over to be shipped.  When you receive your fuel line, you will have to straighten it out. It is a fairly straight forward procedure and we have not had anyone struggle with this to date.

Reproduction OE Steel Fuel Vapor Line for the 1970, 1971, 1972 and 1973 Mercury Cougar or Ford Mustang with 5/16" Fittings

Reproduction fuel line to side apron grommet for the Mercury Cougar or Ford Mustang. 3 needed per car.Replaces Ford part # D1ZZ-9288.

New replacement carburetor mounting gasket for 1970-73 Ford 351C or 351 Cleveland engines. Mounts between the fuel pump housing and the engine.

Exclusive to WCCC, here's our reproduction in-tank, fuel sending unit with the low fuel option. Good for all 1971 - 1973 Mercury Cougar XR7's and all Ford Mustangs with 16 gallon fuel tanks. This is a reproduction of a 1971 fuel sending unit with three prongs (2 electrical and 1 alignment prong). The original Ford casting number was D1WF-9275-AC. This unit comes with a new 3/8 inch filter, brass float, and sending unit gasket. These are completely interchangeable on all 1971 - 1973 20 gallon...

This is the two prong version fuel sending unit for 71 - 73 Cougars and Mustangs. The reason for the two prong, is that this particular year used a ground wire coming off of the sending unit. Cougars equipped with the convenience control package, and the XR7's used a three prong version. The function however is not as good as original but adequate and usually will work for years. If you have an original, often times it's just the float that needs replacing, so don't be quick to discard your...

This is the stainless steel, two prong version fuel sending unit for 71 - 73 Cougars and Mustangs. The reason for the two prong, is that this particular year used a ground wire coming off of the sending unit. Cougars equipped with the convenience control package, and the XR7's used a three prong version. These units are better than original being made from stainless. The function however is not as good as original but adequate and usually will work for years. If you have an original, often...

Reproduction fuel tank for the 71 - 73 Mercury Cougar. 20 gallon capacity, correct in every way. Beware that the Mustang tanks sold by most vendors has a different filler neck angle that doesn't fit Cougars. Replaces Ford part #: D1WY-9002-A ...

We prefer local pick-up only on these used 20 gallon fuel / gas tanks as we cannot ship anything that smells like fuel.

Ford called this part the fuel vapor separator. It mounts to the top of the fuel tank. This is part of the emissions control smog system, the fuel vapors that are collected in the charcoal canister are returned through a hose to this device into the fuel tank. Applications for this part include: 1971-73 Mercury Cougar and Ford Mustang, 1971-72 Pinto and Bobcat, 1971-72 Maverick and Comet, 1971 Thunderbird and Lincoln MKIII, and 1971-73 Ford / Mercury full sized cars. Starting about 1973, this...

Ford called this part the fuel vapor separator. It mounts to the top of the fuel tank. This is part of the emissions control smog system, the fuel vapors that are collected in the charcoal canister are returned through a hose to this device into the fuel tank. Applications for this part include: 1971-73 Mercury Cougar and Ford Mustang, 1971-72 Pinto and Bobcat, 1971-72 Maverick and Comet, 1971 Thunderbird and Lincoln MKIII, and 1971-73 Ford / Mercury full sized cars. Starting about 1973, this...

This is our reproduction, uncut, driver side (left hand), long, front and rear floor pan for your Mercury Cougar convertible.

This is our reproduction, uncut, passenger side (right hand), long, front and rear floor pan for your Mercury Cougar convertible.

Reproduction full length driver side floor pan. This pan is technically for 67 - 68, but will work for 67 - 73 Cougars and Mustangs. There were small differences such as drain holes / no drain holes etc. between the years, but will work for all years. Hi, and sincerely thanks for all help I've received from WCCC during my (mega) 1968 restoration project. If everyone would be that helpful, the world would be a much better place. ;-) My car is almost ready for the road, but - as always - there...

Reproduction full length passenger side floor pan. This pan is technically for 67 - 68, but will work for 67 - 73 Cougars and Mustangs. There were small differences such as drain holes / no drain holes etc. between the years, but will work for all years.

C8OZ-14A187-A Unique 1/4"-20 bolt for attaching the fuse blocks. 69 70 71 72 73 Mercury Cougar Ford Mustang fuse panel attaching bolt. Includes "C" clip and spring as shown. "C" clip keeps the bolt in the black fuse block.

C8OZ-14A068-A Black Bake-O-Lite original fuse block. Grade A, no cracks or chips. Perfect for upgrading your broken fuse block that has a nice wiring harness. 69 70 Mercury Cougar Ford Mustang fuse panel. Sometime in the later part of 1972 Ford switched to a nearly identical brown fuse block.

D1ZZ-14A068-A Black Bake-O-Lite original fuse block. Grade A, no cracks or chips. Perfect for upgrading your broken fuse block that has a nice wiring harness.72 73 Mercury Cougar Ford Mustang fuse panel. We suspect that this brown colored fuse block was used towards the end of 1972 and all of 1973. Identified by the brown color, and having a 20AMP fuse 'cigar lighter and horn' fuse location.

C8OZ-14A068-GRADEB Black Bake-O-Lite original fuse block. Grade B, not broken, but will have chips from prying out fuses. Perfect for upgrading your broken fuse block that has a nice wiring harness. 69 70 71 72 Mercury Cougar Ford Mustang fuse panel. Sometime in the later part of 1972 Ford switched to a nearly identical brown fuse block.

D1ZZ-14A068-A GRADE B Black Bake-O-Lite original fuse block. Grade B, not broken, but will have chips from prying out fuses. Perfect for upgrading your broken fuse block that has a nice wiring harness. 72 73 Mercury Cougar Ford Mustang fuse panel. We suspect that this brown colored fuse block was used towards the end of 1972 and all of 1973. Identified by the brown color, and having a 20AMP fuse 'cigar lighter and horn' fuse location.

C8OZ-14A033-C Brass clip with accessory terminal for attaching the accessory lead wire with multi connector. Attaches to all 1969-70 fuse blocks found on Mercury Cougars and Ford Mustangs. Accessory feed terminal for such things as 1969 swing away steering column, rear window defogger, speed or cruise control, etc. Includes fuse block mounting hardware.

For use with 1967 390 and all 1968-73 air cleaner lids except Ram Air which uses no gasket. Replaces Ford part #C8ZZ-9673.

New carburetor gasket for most 1967-73 2 barrel carburetors. 289/302/351W/351C engines. Replaces Ford Part #: C3AZ-9447-B *Excludes 1968 X code 390-2V premium fuel engines.

Round ring shaped gasket that goes on top of the carburetor. Protects and seals the carburetor to the air cleaner.

[No Description Provided]

New Old Stock Ford small block Ford distributor shaft to engine block gasket, made of rubber. Fits all 260, 289, 302, 351w, 351c engines. 1959-76. This is a "O" ring rubber washer. Will not fit big block FE, 360, 390, 410, 427, 428 engines. Ford part number B9TF-12143-A.

New Old Stock Ford FE distributor shaft to engine block gasket, made of rubber. Fits all FE or 352, 360, 390, 410, 427, 428 engines. 1958-76. This is a tapered rubber washer. Will not fit small block Windsor or Cleveland engines. Ford part number B8A-12143-A.

Ford FE distributor shaft to engine block gasket, made of rubber. Fits all FE or 352, 360, 390, 410, 427, 428 engines. 1958-76. This is a tapered rubber washer. Will not fit small block Windsor or Cleveland engines. Ford part number B8A-12143-A.