1972 Mercury Cougar

Replaces Ford Part # C8AZ-2069-A Sold individually

All new disc brake pads are supplied to us by brand name manufacturers. Boxed sets of four pads.

All new premium disc brake pads are supplied to us by brand name manufacturers. Set of 4 pads. Low dustProtective underlayerRubber/steel/rubber layered shimScorched

Longer arm than drum brake pedals. Comes with all mounting hardware. Pedal shipped bare, picture may show hardware and pedal pad with trim. Most of these pedals are dated as shown. It makes it fairly easy to identify them by year.

Reproduction drum brake pedal pad for the Mercury Cougar or Ford Mustang equipped with an automatic transmission. The 1967 version of this piece is narrower than this 1968-73 piece.Replaces Ford part # C6OZ-2457-A.

Reproduction brake pedal pad for the Mercury Cougar and Ford Mustang equipped with a manual transmission and drum brakes. This unit is a good fit and is a quality part. Replaces Ford part # C5ZZ-2457-G.

Excellent quality replacements. Includes hub, studs, and bearing races. Single piece design. 2" spacing from hub to rotor face

Used driver (left hand) side brake shoe adjustor for Mercury Cougar or Ford Mustang. This screw assembly is part of the manual and self adjusting system for your drum brakes either front or rear. These have right and left handed threads depending upon which side of the car they are intended. Left side screws are identified by an "L" on the end of the screw under the socket and a single groove machined into the pivot nut. Original Ford part number for the passenger (right hand) side is...

Used passenger (right hand) side brakes shoe adjustor for Mercury Cougar or Ford Mustang. This screw assembly is part of the manual and self adjusting system for your drum brakes either front or rear. These have right and left handed threads depending upon which side of the car they are intended. Right side screws are identified by an "R" on the end of the screw under the socket and a two grooves machined into the pivot nut. Original Ford part number for RH or passenger side is C2OZ-2041-A,...

Reproduction 10 x 2-1/4 inch premium semi-metallic front drum brake shoes for Mercury Cougar or Ford Mustang with front 10 inch drum brakes.  Double check that shoe width measurement on your car, there were some cars sold with 2-1/2 inch wide shoes.

New front10 X 2-1/2 inch brake shoes for the Mercury Cougar or Ford Mustang. These will fit the rears of some Ford vehicles, but not a Cougar or Mustang without modification.Typically this size of brake shoes is only found on the front of a Cougar or Mustang. You would have to have 2-1/2 rear backing plates in order to use these shoes on the rear of your car.

Premium grade of rear brake shoes with semi metallic brake linings. 10 inch diameter drum brakes. Please measure your brake shoes, there are also 1-3/4 inch wide shoes too.

Often when your fuel gauge is acting up, this is the culprit, not the gauge or sending unit. The benefit of using this foam float, is that sometimes the hollow brass float will leak, causing a bad reading. This foam version of the float is fuel resistant and will never leak. Replaces Ford part #C0AZ-9202-B.Check out the video below on our new gauge tester: ...

Often when your fuel gauge is acting up, this is the culprit, not the gauge or sending unit. The problem with these brass floats, is that after year of being in contact with fuel, they will begin to corrode and disintegrate. We suggest going with the new foam floats. They are fuel resistant and will last longer. Find it here. Replaces Ford part #C0AZ-9202-B.Check out the video below on our new gauge tester: ...

Core bucket seat frame bottom for the Mercury Cougar or Ford Mustang. This unit is the same from driver side (left hand) to passenger side (right hand) and is the same whether you have a standard, decor or XR7. The base is the same whether you have center release or side seat back release. The foam almost will always be deteriorating, or even missing, and will need to be recovered. These units will be solid core frames taken from a Western parts car but keep in mind they will always have a...

Core driver side (left hand) and passenger side (right hand) pair of bucket seats with side seat release for the Mercury Cougar or Ford Mustang. The seat frame is the same in the standard, decor or XR7 and are the same driver to passenger side. The foam almost will always be deteriorating, or even missing, and will need to be recovered. These units will be solid core frames taken from a Western parts car. Seat tracks are sold separately. Seat hinge covers and hardware available...

Core driver side (left hand) bucket seat with the side seat release lever for the Mercury Cougar or Ford Mustang. The foam almost will always be deteriorating, or even missing, and will need to be recovered. These will be solid core frames taken from a Western parts car. Seat tracks are sold separately. Seat hinge covers and hardware available separately. *NOTE* Want to save on shipping? If you only need the bottom portion of the bucket seat we can discard the upper portion. The...

Core passenger side (right hand) bucket seat frame with center seat release for the Mercury Cougar or Ford Mustang. This unit is the same driver to passenger side. The foam almost will always be deteriorating, or even missing, and will need to be recovered. These will be solid core frames taken from a Western parts car. Seat tracks are sold separately. Seat hinge covers and hardware available separately. *NOTE* Want to save on shipping? If you only need the bottom portion of the...

Core passenger side (right hand) bucket seat with the side seat release lever for the Mercury Cougar or Ford Mustang. The foam almost will always be deteriorating, or even missing, and will need to be recovered. These will be solid core frames taken from a Western parts car. Seat tracks are sold separately. Seat hinge covers and hardware available separately. *NOTE* Want to save on shipping? If you only need the bottom portion of the bucket seat we can discard the upper portion. The price...

Grade A used driver side bucket seat textured plastic trim panel. Available in black, blue, red, ginger, avocado, green, and white. Please specify in the notes your desired color, ginger seems to be the most prolific color, the others may or may not be available. Grade B will have scuffs and or scratches, might also be chalky in a couple of places. Various Ford part numbers associated with this panel, here are a few: D12B-6260763, D3ZB-6561633, D1FZ-6260763, D2ZZ-6260763, and...

Grade B used passenger side bucket seat textured plastic trim panel. Available in black, blue, red, ginger, avocado, green, and white. Please specify in the notes your desired color, ginger seems to be the most prolific color, the others may or may not be available. Grade B will have scuffs and or scratches, might also be chalky in a couple of places. Various Ford part numbers associated with this panel, here are a few: D12B-6260762, D3ZB-6561632, D1FZ-6260762, D2ZZ-6260762, and...

Used on the majority of Fords, this assembly can easily be removed without cutting or un-stitching the webbing. No rust, grade "A" show quality chrome, originally came stamped ROBBINS - JR - 7600 or HAMILL H-000. If you have a preference as to which version you would like just let us know in the memo box at checkout. Check out our video "All about seat belts" below. ...

Correct Backup Light Bulb for the 1967 - 1968 Mercury Cougar. Owners Manual and shop manual incorrectly state the backup light bulb to be the 1156.

Brand new 1157 (dual-filament) exterior stop lamp / turn signal light bulb for the Mercury Cougar or any vehicle equipped with 1157 bulbs. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. For even brighter...

The 67 -73 Cougar uses the 1157A (Amber) bulb for the turn signals.  This bulb will also fit other applications that require an 1157A or 1157NA bulb. Replaces bulb #: 1157A or 1157NA

Replacement lamp for the speedometer, heater controls, ashtray, automatic shift indicator, low fuel, seat belt reminder, or emergency flasher warning lights on the visual check panel.

New 1895 bulb for the instrument clusters. *Note - The table and the owners manuals are wrong for the Visual Check Panel bulbs, Ford literature calls out a 1895 bulb, when in fact the correct bulb is 1891.

Reproduction 194 light bulb that can be used for your gauges, high beam indicator, clock, or turn signal indicators for the Mercury Cougar.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

Reproduction 631 Glove / Luggage Compartment / Under Dash Courtesy / Trunk Light Bulb for the 1967 - 1973 Mercury Cougar

Used rubber bumper that fits into the bracket in the bottom center of the door shell. Fits all 1967-68 Mercury Cougar and 1965-68 Ford Mustangs. This is the rubber bumper for the window rest when the door glass is at its lowest. Bracket is in bottom of the center of the door. Fits both right and left doors. Correct for 1967 - 1968 but will work in 1969 - 1970 with Bolt-in glass if you cut it down. Sold separately, two required per car. Replaces Ford part # C5ZZ-6521762-B  Check out...

These bumpers are re-chromed using the triple plating process. This produces a significantly higher quality finished product because they have a layer of copper, nickel and chrome. It is well worth the hassle and expense by paying a little extra now rather than changing out your bumpers out again in one to five years because the chrome is beginning to deteriorate. For years now, many of the nations top honor Cougar's have worn our bumpers.Please know that chrome cracking from the installation...

These bumpers are re-chromed using the triple plating process. This produces a significantly higher quality finished product because they have a layer of copper, nickel and chrome. It is well worth the hassle and expense by paying a little extra now rather than changing out your bumpers out again in one to five years because the chrome is beginning to deteriorate. For years now, many of the nations top honor Cougar's have worn our bumpers.Please know that chrome cracking from the installation...

Mounts to the bottom lip of the coil spring cover, two required per car, sold individually. Replaces Ford Part #: C9OZ-3020-B.

Mounts to the bottom lip of the coil spring cover, two required per car, sold individually. Ford Part #: C9OZ-3020-B.

This option includes paying a core charge. By choosing this option, the re-chromed bumper you receive will have started the re-chroming process as an average quality core. We highly recommend that you send us your core first. Here's why: We can core match your bumper. Bumpers that are re-chromed using a superior quality core are always reserved for core matching. If your core is average or below average, you may be able to pay to upgrade to a re-chromed bumper that started the re-chroming...

Mounts over rear axle ends into the body/frame, two required per car, this is the more pointed Christmas tree shaped version.Ford part # C6AZ-4730

Rubber bumper / stop that sits atop the vertical center grille support on the 71 - 72 Cougar. Most times, these are very brittle and crumble when you handle them, but every once in awhile we have a bad support piece and we're able to salvage the rubber bumper.

This bumper bolt is sold individually and replaces Ford part # C4ZB-17758-A. It features the correct "button" head profile covered in stainless steel. Silver zinc with wax coating to extend plating life. Reduced shoulder height allows the nut to seat properly.Please know that chrome cracking from the installation of bumper bolts on our rechromed bumpers is not covered under warranty. We have observed that some reproduction wavy washers are of a thicker material than original and require more...

This is a complete bumper bolt kit for front and rear.Please know that chrome cracking from the installation of bumper bolts on our rechromed bumpers is not covered under warranty. We have observed that some reproduction wavy washers are of a thicker material than original and require more torque to flatten out properly for a good fit. We suggest that no matter what thickness your repro wavy washer is that you flatten them out in a vise prior to installation so as not to have to apply as much...

D1WY-17767-A Front bumper mounting arm for 1971-72 Mercury Cougars, driver side.

D1WY-17766-A Front bumper mounting arm for 1971-72 Mercury Cougars, passenger side.

D1WY-17755-A Front bumper outer mounting bracket for 1971-72 Mercury Cougars, driver side.

D1WY-17754-A Front bumper outer mounting bracket for 1971-72 Mercury Cougars, passenger side.

D1WY-17788-A Rear bumper bracket for any 1971-72 Mercury Cougar, driver side only. This bracket is located on the inside of the trunk.

D1WY-17787-A Rear bumper bracket for any 1971-72 Mercury Cougar, passenger side only.

Complete five piece set includes the horizontal support as well as the two braces inside the trunk, two brackets that bolt to the bumper and hardware. Checked closely for bends, cracks and stripped threads. What is pictured is the best of what we have, we also have B grade sets that will clean up fine. Pair of inside the trunk bumper mounting brackets D1WY-17A750-A. Passenger side bumper bracket D1WY-17787-A, driver side bumper bracket D1WY-17788-A. Rear bumper center reinforcement beam...

Complete five piece set includes the horizontal support as well as the two braces inside the trunk, two brackets that bolt to the bumper and hardware. Checked closely for bends, cracks and stripped threads. What is pictured is the best of what we have, we also have. These B grade sets will clean up, but have some slight surface rust. Pair of inside the trunk bumper mounting brackets D1WY-17A750-A. Passenger side bumper bracket D1WY-17787-A, driver side bumper bracket D1WY-17788-A. Rear bumper...

Good used set of crack free, bend free original brackets. These are Western parts that have never been exposed to road salt and can easily be restored to show quality standards. Kit includes: right and left inner bumper brackets, right and left outer brackets, front beam (missing from picture), and center bumper reinforcing bracket.