1969 Ford Mustang

Service replacement NOS passenger side hood hinge for Mercury Cougar and Ford Mustangs. 1978 manufactured date, this one is painted a gloss black color. New old stock hood hinge less spring. These hinges will work on 1970 Cougars, but because the grill center is attached to the hood during that year. The hood hinge requires heavier duty springs to accommodate the additional weight on the hood.Ford part # C5AZ-16796-B, C8AZ-16796-A, and C9AZ-16796-A.Anghel Restorations offers a very detailed...

This kit is the same Scott Drake "Shelby Style" DELUXE hood pin kit offered by many other vendors.Kit includes 2 Hood Pins, 2 dowel pins, 4 Nuts to hold the dowel pins on, plates for the top of the hood, 8 screws to hold the hood plates on and 2 tie down cables. The difference between the standard version and this deluxe version, is that the standard is chrome plated and the deluxe is stainless steel. Common consensus is that the holes for the pins were hand drilled at the factory, so the...

This item has been discontinued until further notice.Basically correct looking except for screws in place of the rivets. The High or Low tone is indicated in raised letters located on the perimeter of the horn. Replaces Ford Part #: C9ZZ-13832 / C9ZZ-13833 or C9ZF-13801-B / C9ZF-13802-C.

Tested and working used Hi tone horn. The Hi tone is indicated in raised letters located on the perimeter of the horn. 1969-70 Mercury Cougar and Ford Mustangs used part number C9ZF-13801-B Hi tone. Every horn is bench tested and inspected for cosmetic defects, if they do not function properly, and pass a visual inspection, they get recycled. The used horns at WCCC can be used as-is or you can clean and detail them for you show car.

Tested and working used Lo tone horn. The Lo tone is indicated in raised letters located on the perimeter of the horn. 1969-70 Mercury Cougar and Ford Mustangs used part number C9ZF-13802-C Lo tone. Every horn is bench tested and inspected for cosmetic defects, if they do not function properly, and pass a visual inspection, they get recycled. The used horns at WCCC can be used as-is or you can clean and detail them for you show car.

Reproduction gas tank to filler pipe hose fits the 67 to 70 Mercury Cougar, measures 4 1/2" long. Excludes 1970 with California emissions. Even if yours is not cracked it will be hard if it is over two decades old. We highly suggest you replace this part if yours is in fact hardened with age because a minor rear end collision could cause it to fail and send fuel spilling into your trunk area. Replaces Ford part #: C8ZA-9047-A.

This Pump to Value Outlet Pressure Hose is 100% correct for the 1967, 1968, 1969, 1970 big block. This hose has industrial high pressure fittings that are much higher quality than those available by most Mustang / Cougar Parts Dealers. Replaces Ford Part #: C9OZ-3A319-C.

C9OZ-6A664-A Original used hose that connects the original PCV valve to the carburetor spacer plate. All 1969-70 351 Windsor 2V and 1969 351Windsor 4V engines. Used hoses will have faded striping (if present), and clamp impressions. Very often the rubber will be hard and showing some degree of stress cracks. This hose is a bit longer than the 289/302 version due to the taller deck height of the 351 Windsor engines. *Note - These molded and contoured hoses were designed to work with the...

C7TZ-6A664-A Used after 02-21-1969. Original used hose that connects the original PCV valve to the carburetor spacer plate. All later 1969 S code 390-4V engines. Used hoses will have faded striping (if present), and clamp impressions. Very often the rubber will be hard and showing some degree of stress cracks. *NOTE* These molded and contoured hoses were designed to work with original style PCV valve (modern 90° PCV valves won't work). Additionally anything other than period original intake...

Used vacuum hose with inline muffler, connects the Servo Valve to the Regulator on 1969 Mercury Cougar and Ford Mustang with factory Speed Control. Hose about 42.7509 inches long. Ford number for hoses is C9ZZ-9D860-A.

Good used original power steering lower hose bracket and retainer with a new reproduction insulator installed in place of the original crusty or missing insulator.This bracket is for cars with the big block routed power steering hoses.

Used connector plug that attaches to the A/C vacuum switch assembly on the 69 - 72 Cougar or Mustang. The six vacuum hoses are molded into the plug, and for those instances when someone has cut a hose, simply use a hose connector.

This is the correct control valve end hoses that comes from the power steering pump on all big blocks and the 1969 and 70 small blocks, and will work for the 1967 or 1968 small blocks with the 5/16 inch control valve fitting if the power steering hoses are routed the same as on the big block engines. Includes both Pressure and Return hose that connect to the control valve. The big block routing is far superior to the original routing as the original routing was susceptible to rubbing against...

We are one of the only Mustang / Cougar vendors that carry "correct" power steering hoses for your early, big block Cougar or Mustang. The tubing bends are all "spot on" and the portion that passes through the rubber insulator are identical to NOS. You will not find all of these hoses at your local auto parts store or the the "Mustang Discount" folks. Fits the FE Big Block 390, 427 & 428 Mercury Cougar or Ford Mustang with or without Power Steering Cooler.  Be sure to select the option to...

This is the 1967- 1968 retrofit or re-route hose kit! The tubing bends are all "spot on" and the portion that passes through the rubber insulator are identical to NOS for 1969. You will not find these at your local auto parts store or the the "Mustang Discount" folks. These hoses will also work on a 1967 or 1968 5/16" control valve fitting if it is routed the same as the big block. You will need to purchase the power steering hose bracket for the big block in order to make it work. This is a...

[No Description Provided]

Used A grade dog dish style hubcaps / wheel covers for the Mercury Cougar as well as other Mercury and Ford products. Used item as would have been found on 1969 Eliminators as well as other models with the plain poverty or dog dish center cap, about 7-1/2 inches in diameter. Replaces Ford part # C8OZ-1130-G, or C8MY-1130-A. Fits: 1969 Mercury Cougar Eliminator / Cyclone1970 Mercury Cougar Eliminator / Cyclone1971 Mercury Cougar / Cyclone1972 Mercury Cougar 1973 Mercury Cougar 1969 Ford Mustang...

The Hustler Stick features heavy-duty 1-1/4" diameter tubing, and is an alignment bar designed for bumpers, hoods, decks, panels etc. Made in the USA, it has a 1/4", 6 foot long chain with hooks at each end. This versatile tool is very useful in shaping damages on a vehicle body. To use it, hook it up to the panel or bumper, anchor the stick properly, and pull it by hand.We will loan this hustler stick for 60 days, with a 100% refundable purchase price. Tool must be returned in undamaged...

Tag marked HBA-BF or HBA-BF1 for use on 1967-68 Cougar and Mustang with power steering pumps originally installed on 289/302/390/427 and all 1968 428CJ engines. Various dates, and could be designated for either a Ford-Thompson (F) or TRW (W) power steering pump. For 1969 dated tags please see the related listing.*Please Note - Current inventory is exclusively 1967-68.

Fits all 1967-70 Mercury Cougar and Ford Mustang with factory manual steering. Rarely did these last 60,000 miles. To find one after 50 plus years is quite a find! These are intended for professional restoration with new bushings prior to installation. That is why they are graded as "CORE GRADE". Very limited quantities, we offer core grade suspension parts for those car owners that wish to avoid reproduction parts. Typically this manual steering, idler arm would have had a pink...

Quality reproduction. Fits all 1967-70 Mercury Cougar and Ford Mustang. Rarely do these last the life of the rest of the front suspension, if you get 60,000 miles out of one you are lucky. The slightest amount of play in this component will translate to major slop in the steering. Lin, Hey, just wanted to thank you for your prompt service. Last Friday 4/24/09 I ordered a 71 - 73 Idler Arm and today (Monday 4/27/2009) I received it. WOW!!! I just wanted to let you know that you guys are...

Fits all 1967-70 Mercury Cougar and Ford Mustang with factory power steering. Rarely did these last 60,000 miles. To find one after 50 plus years is quite a find! These are intended for professional restoration with new bushings prior to installation. That is why they are graded as "CORE GRADE". Very limited quantities, we offer core grade suspension parts for those car owners that wish to avoid reproduction parts. Typically this manual steering, idler arm would have had a yellow paint mark on...

This reproduction emergency / parking brake idler bracket welds to the under side of the floor on the driver side (left hand) of the vehicle and has the factory spec pin.

New old stock bracket and pulley assembly for Cougars or Mustangs equipped with the 289, 302, or 1969 351W engine. We also offer a bearing replacement service to rebuild your 289, 302, or 1969 351W fixed idler pulley, see item 27539. Ford part # C8AZ-8678-C. ...

Used fixed idler bracket and pulley assembly with new installed bearing for 1968-69 Cougars and Mustangs with the 390 or 428CJ engine. This part will have a small bearing on the pulley and is not marked with a casting number. The 1970 bracket and pulley assembly was a service replacement part and are the same as the 68-69 with the exception of a slightly larger bearing. This later service replacement part is an economically priced service replacement for the earlier originals. All pulleys come...

NOS ignition switch kit for any 1968-69 Mercury Cougar or Ford Mustang. Includes ignition cylinder and plug with pigtail wires. This is a new old stock Motorcraft part. Comes as shown, you will need to reuse your key lock cylinder. Ford part number D1AZ-11572-C.

C8OZ-3C511-B Rear power steering pump support bracket. Also called the high pressure hose indexing bracket. For any 1968 - 1970 Cougar or Mustang with any of the 390 / 427 / 428CJ engines. OEM used part designed to maintain the position of the high pressure power steering hose from coming in contact with with moving or high heat parts. *Note - May or may not work with non-original or replacement high pressure hoses.

Universal driver side (left hand) or passenger side (right hand) inner floor frame patch that you can trim to fit the area that needs to be repaired.

Full driver (left hand) side front frame rail that measures 52" long. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...

Full passenger (right hand) side front frame rail that measures 52" long. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...

Grade A used inspection plate cover for all 390-4V and 428CJ engines with a manual transmissions, both 3 and 4 speeds. All years 1967 - 1970. Access cover to the flywheel and clutch. This is a real clean rust free cover but if you are wanting to save money, we have grade B's which will have a dent or creases for about half the price. Find the grade B here.Ford part number C3AZ-6366-A. ...

C9ZE-9425-A or -B Cast iron intake manifold used on all S code 390-4V engines in a Mercury Cougar or Ford Mustang. Stock 4 barrel intake manifold. Take off manifold with correct casting number of C9ZE-9425-A or -B. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C9ZZ-9424-A. Current date 8H14.*Installation Tip - A water heated aluminum spacer plate with PCV provision is needed for proper air cleaner clearance....

C9ZE-9425-D or C9ZE-9425-E Cast aluminum intake manifold used on all 1969 G code Boss 302 engines in a Mercury Cougar Eliminator or Ford Mustang. Stock 4 barrel intake manifold. Take off manifold with correct casting number of C9ZE-9425-D or -E . Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C9ZZ-9424-C. Has "Buddy Bar" cast into the bottom side.

Cast aluminum Sidewinder intake manifold. Over the counter speed part for the 427 Medium Riser. The offset carburetor placement was to help provided equal length runners in regards to flow. Single 4 barrel intake manifold as shown. Looking closely at the photos, this one has had a repair performed in the past. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford casting number C6AE-9424-J.

Reproduction intermediate pipe exhaust bracket for the 67 - 70 Cougar or Mustang. Used on big block vehicles equipped with the transverse muffler. Attaches to the resonator exhaust hangers just before the muffler pipe rises above the rear end. Sold individually, 2 required per car.

Used intermediate pipe exhaust bracket for the 67 - 70 Cougar or Mustang. Used on big block vehicles equipped with the transverse muffler. Attaches to the resonator exhaust hangers just before the muffler pipe rises above the rear end. Sold individually, 2 required per car.

This used conversion kit includes the controller and switch to convert your standard two speed wiper system over to delay wipers. Controller part # C9ZB-17C476Switch part # C9ZF-17A553-B

Rubber isolator used in tilt away steering column near the lower bearing. Two required per car. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Reproduction jack and tool bag for the trunk area of your Cougar or Mustang. Made in the same plaid style as the trunk mat on the outside, and a white soft liner on the inside. Measures 16 1/2" x 8 1/2"

This is the original JB Weld. We decided to bring this stuff in as a convenience to you, our customers. Why not buy a pack so that the next time you need to bond something together, you'll have a couple of tubes handy? No need to get up and go to the hardware store. With just a few clicks of your mouse, you can have it at your door in a few days (more or less, depending on your location). Good for all sorts of projects around the house or garage.

According to the MPC, this "Transmission Kick Down Control Shaft Rod" is used on all C6 Cougars and Mustangs in 1969, including the 390 and 428 Cobra Jet.  Our research and in hand examples off original Cougars would differ. Because of the different intake manifold used on the 390, Autolite carburetor vs. Holley and different exhaust manifolds we have found that the 1969 390 IP with C6 is distinctly different than the 428CJ and stands on its own by not interchanging with any...

Used on both 351w 2V and 4V FMX transmissions in 1969. Approximately 17-1/2" long with a black color code paint daub on the end closest to the carburetor. This is not correct for any 1970 Cougar equipped with a 351 Cleveland or Windsor motor. *NOTE* Although the MPC lists this part as 1969 only it does in fact apply to the 1970 Cougars equipped with the 351 Windsor two barrel motor. Not only did Ford confuse the public by giving both the 1970 351C 2V and 351W 2V the same engine code "H" in...

Good reproduction of a knob that is always broken off. Made from milled aluminum rather than plastic as the originals were made. This makes it so it is not as susceptible to breaking off. Unique to Cougars with tilt columns in 1968 - 1969. Replaces Ford part number C8MY-17513-C. This part also fits the 68-69 Mustang, Lincoln, Marquis, Thunderbird and other like models with an adjustable steering column.

Used emergency flasher knob for the tilt / tilt away steering column equipped Mercury Cougar or Ford Mustang. This unit is a very fragile part which we never find in good used condition. What you will see when it has been broken off is an exposed Phillips screw head. *NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this service is $90 per hour and most columns with serious problems do need complete tear down and build up which usually takes...

Good chrome, better fit than the reproductions we sell.

Very nice knob with no missing / lifting chrome. If you don't mind some damage on your knob we have plenty that are less than perfect, mention it and we will give you one for free with your order.

Used knob for the speed control or cruise control switch for any 1969 Mercury Cougar or Ford Mustang. Very rare and expensive option for 1969. About 1% of 1969 Cougars had this option and way less than 1% of Mustangs had this option. Switch hangs down over the radio. Look in your owners manual for exact location.   *Knob only - Switch sold separately.

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. Used upper knuckle for the tilt / tilt away steering column equipped Mercury Cougar or Ford Mustang.  There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way...