1969 Ford Mustang

8-32 x 1 inch long screws for attaching automatic shift bezels on 1969-73 Mercury Cougar or Ford Mustang with added Mass Backed Carpeting. Shiny zinc screws as shown, set of 4. Replaces Ford Part #: 381571-S

Used to seal the Aluminum shifter housing to the transmission tunnel. Replaces Ford part #: C9ZZ-7370. Check out our video on rebuilding your shifter below: ...

Reproduction Clutch Pedal Rod To Firewall Seal. Replaces Ford Part #: C6OZ-7533.*NOTE* From personal experience we have found these do not stay attached to the firewall as well as the originals. An adhesive will remedy this problem.

Fits along the lip of the cowl cover and seals to the underside of the hood. Replaces Ford Part #C9ZZ-16740. 

Perfect fit. Replaces Ford part #: C9ZZ-3513.

Wheel seal for both front disc and front drums, 1967-73 Mercury Cougar and 1967-73 Ford Mustang with V-8. Seals sold individually. Two of these are needed, one for each side on the front.

Reproduction foam seal or gasket for the Bendix style disc brake vacuum booster. The MPC books indicate that this seal was used between 1969-71, our guess is that it was deemed 'not needed' after 1971 as a cost cutting measure. We still like to use them though.Ford part number C9ZZ-2B022-A.

Comes with attaching staples made of stainless steel. Applications: 1967 - 1969 Cougars and Mustangs equipped with the 390 engine, and 1970 Cougars and Mustangs with the 428CJ engine. Replaces Ford part #: C4DZ-16238.Not all cars were assembled with this seal, some came with staples, and others used clips.

Oil seal for rear axle on any 1967-73 Mercury Cougar or Most Ford cars with 28 spline axles. Most all Cougar and Mustang received 28 splined axles, whether they have an 8 inch or nine inch rear end from the factory. Seal measurements: 1-3/8 inch inside diameter, 2-17/64 inch outside diameter. Two needed per axle, sold individually. We stock Timken brand of seals.Replaces Ford part number C7OZ-1177-B.

Oil seal for rear axle on any 1968-73 Mercury Cougar or Most Ford cars with 31 spline axles. Typically only 428CJ, 427-4V, and Boss 302's got the heavy duty 31 splined axles from the factory, most Cougar and Mustangs have 28 splined axles. Seal measurements: 1-1/2 inch inside diameter, 2-17/64 inch outside diameter. Two needed per axle, sold individually. We stock Timken brand of seals.Replaces Ford part number C7OZ-1177-A.

When it's time to replace your old decaying foam seal, go with our reproduction weatherstrip retainer foam roll with peel off adhesive. Goes between the roof and door / window channel.  These are not technically manufactured to fit the Cougar / Mustang, however these are very close to the originals and come from the manufacturer in a roll that is 4' X 1" X 1/8".  One roll is more than enough to do one side, but you will need 2 rolls to do both sides. ...

These vinyl coated clips hold the weatherstrip and guide the window when rolling up. Used clips usually are rusted and the vinyl portion is peeling. Sold individually and four are required per car. Replaces Ford part #: C9ZZ-6522204. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! 1969 Glue-In Glass: The Comprehensive Repair Guide Video ...

We suggest using white lithium grease or petroleum jelly to ensure the seal will not stick to the shift lever. Fits 1969-73 Mercury Cougar and Ford Mustang, additionally it also fits 1971+ Maverick and Comet with floor shift automatic only.  If you have any side-to-side play in the shifter, this seal will not last. We do have the shifter bushings available. Replaces Ford part  numbers C9ZZ-7D351-A & D1ZZ-7D351-A. Get the matching mounting clips here. Check...

Top Loader transmission input shaft seal, small shaft, 289, 302, 351, and 390 only. Quality Timken part. Fits all 3 and 4 speed Top Loader Ford transmissions 1967-73 Mercury Cougar and 1965-73 Ford Mustang. Follow manufacturers instructions for installation or go to YouTube University.*Note - excludes big shaft 428CJ, 429CJ, and Boss 429 transmissions.

Top Loader transmission rear seal, 28 splined shaft, 289, 302, 351, and 390 only. Quality Timken part. Fits all 3 and 4 speed Top Loader Ford transmissions 1967-73 Mercury Cougar and 1965-73 Ford Mustang. Follow manufacturers instructions for installation or go to YouTube University. *Note - excludes big shaft 428CJ, 429CJ, and Boss 429 transmissions.

Top Loader transmission rear seal, big shaft 31 splines, 428CJ, 429CJ, and Boss 429 only. Quality Timken part. Fits 4 speed Top Loader Ford transmissions 1968-71 Mercury Cougar and 1968-71 Ford Mustang. Follow manufacturers instructions for installation or go to YouTube University.

Contoured stainless steel trim for the driver side door glass. Application all 1969 Mercury Cougar and Ford Mustang hard top and coupes. See accompanying rubber seal Ford part #C9ZZ-65214A15-A. Our grade "A" door glass trim for 1969 will not have heavy scratches and the small bend over tab at the top will be in place. These will polish up to a show quality luster. Used (poor condition) weather strip may or may not be in place. Please go to our rubber section to select the new rubber strips...

This is the driver side trim / moulding that mounts to the door window and creates the seal between the door glass and the quarter window on 69 Cougars and Mustangs. Get the seal you need for this moulding here.

Unlike our un-restored used door glass trim and are sold in pairs only. If you are doing a concours correct restoration then these would not be for you as they have been "over restored" to a mirror like finish. The down fall of having such a mirror like finish is they get finger prints on them every time you touch them. The good part is they look HOT! Very nice touch to that resto-mod that cannot get enough bling.When sending cores, they must be in good shape or an upgrade core fee will apply....

Contoured stainless steel trim for the passenger side door glass. Application all 1969 Mercury Cougar and Ford Mustang hard top and coupes. See accompanying rubber seal Ford part #C9ZZ-65214A14-A Our grade "A" door glass trim for 1969 will not have heavy scratches and the small bend over tab at the top will be in place. These will polish up to a show quality luster. Sold separately, please choose between driver or passenger side. Used (poor condition) weather strip may or may not be in place....

This is the passenger side trim / moulding that mounts to the door window and creates the seal between the door glass and the quarter window on 69 Cougars and Mustangs. Get the seal you need for this moulding here.

Replacement seal with boot for all 1965-73 C4 Ford transmissions. Tail shaft and slip yoke seal. 

If your power steering control valve unit is in good working condition but seems to be leaking, this seal kit may be all it takes to correct the problem. Keep in mind many of the high mile control valves in circulation are worn beyond factory tolerances and are not easily rebuilt. Our re-manufactured units are a great solution if this is the case. We also have the complete rebuild kit available.  NOS power steering control valve seal kit.  Ford part number C3AZ-3A650-B. ...

If your pump works fine but leaks this is an easy kit to install. Replaces Ford Part #: D1AZ-3B584-A.

Sold as a pair, correct for coupe or convertible. Will fit the 70 coupe or convertible as well, but correct for the 1969. Replaces Ford part # C9ZZ-6528182 & 3B. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! 1969 Glue-In Glass: The Comprehensive Repair Guide Video ...

Kit includes all repair parts necessary to refurbish leaking cylinder/piston rod seal area. Replaces Ford Part #: C1AZ-3A764-A.

New and improved reproduction bottom of the door seal for the 1967 - 1970 Mercury Cougar or Ford Mustang. Unlike previous versions, these are now made with denser material and are much more rigid. They measure 38" for 1967 -1968 and 41" for 1969-70 so you will have to trim them down if you have a 1967-68. One of the most common missing parts on a 1967-70 Mustang or Cougar today is the lower weatherstrip seals on the doors. These seals were added to cars to keep dirt and moisture from entering...

Reproduction door glass seals for the front of the door to the window glass for the Mercury Cougar or Ford Mustang. Replaces Ford part # C9ZZ-6520264. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! 1969 Glue-In Glass: The Comprehensive Repair Guide Video

Premium reproduction rubber seal with the proper thickness of the 1967-68 seal as found on Mercury Cougar and Ford Mustang except these are not molded to the extension contours. Starting in 1969 this channel seal was manufactured slightly smaller which tightened up the gap on the fender and quarter extension seals. This seal maintains the slightly larger gaps. Sold as a pair, two pairs needed per car.  Each package has 2 strips of 25 1/2" lengths. *NOTE* Do not over tighten the...

Correct heater box seal kit for 1969 and 1970 Cougars and Mustangs. Replaces Ford part #: C9ZZ-18500-B. Check out our video below on how to replace a heater core! We used a '69 Cougar with A/C, but many of the same concepts apply to other years.

This kit is designed for the 1969-1970 heater A/C box. Replaces Ford Part #: C9ZZ-18500-A. Check out our video below on how to replace a heater core! We used a '69 Cougar with A/C, but many of the same concepts apply to other years.

Fits RH or LH standard interior, two required per car. Has correct grain texture and injection molded exactly like originals. Includes metal clip retainers pre-installed as well as the clips themselves. Use any solvent based paint to match the color of your interior. These were used on the 69 - 70 (and some 68) Mustangs but only used in 1970 for the standard model Cougar.Sold individually Replaces Ford part #: C9ZZ-6560762.

Pressure die cast with show quality chrome. Easy to install, correct fit and finish, inexpensive way to spruce up your interior. Remember when we used to send these out and pay big money to have them replated? Sold as a pair, hardware included.

Sold as a pair

Passenger side seat back release assembly, can me used for a conversion of 1970 high-backed seat backs for use in 1969 Mercury Cougar Eliminator and Ford Mustang Mach 1. This assembly has the release lever mounted nearly at shoulder level, factory 1970 high backs have the latch release at the hinge. This is a sneaky way to 'create' the factory 1969 high backed seats from 1970 seat backs. Comes with all hardware as shown. See picture for locating the three holes required for installation in a...

Used passenger side seat back release catch for the 68 - 70 Cougar or Mustang.

Fits 1967 and 1968 Standard or XR7. Holds "J" shaped plastic hinge covers in place.

Great looking replacement style seat belts. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colors. Please note: this is the only aftermarket shade of Aqua, which was only used on the Ford Mustang. Contact us for availibility of good used Cougar correct aqua seat belts.Sold individually

These are era-correct looking seat belts at an affordable price.  These are not Concours reproductions, but have the correct vintage look used by Ford on multiple cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals.Sold individually Includes: 1 Complete non-retracting seat belt (includes both male and female side)2 Bolts, nuts, and lock washers

Great looking replacement style seat belts. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colors.sold individually

These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included!sold individually

Great looking replacement style seat belts. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colors.sold individually

These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included!sold individually

Great looking replacement style seat belts. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colors. Sold individually

These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included!sold individually

Finally! A cure for those peeling chrome bezels on your car with deluxe seat belts. If your plastic bezels on your 68-72 standard belts are two part construction, you can upgrade with these attractive bezels. Before these were reproduced we used to hunt high and low for good used units from rear belts out of parts cars. Perfect fit and great quality. Sold as a pair, six per car on coupes, four per car required on convertibles. Replaces Ford part # C8AZ-65611A72-A

Now you can restore your 1968-72 Cougar or Mustang’s deluxe seat belt buckles back to their original showroom condition by replacing cracked, broken, or missing components with the new seat belt buckle restoration kit. Tooled to the original factory specifications from OEM quality injected molded black plastic. This seat belt buckle kit features the correct texture grain pattern and starburst medallions for a perfect restoration. The release button and spring are included. One kit does a pair...

These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included!Sold individually