1969 Ford Mustang

Contains nut and washer. Fits all Ford alternators. AMK F-644.

Reproduction brake and fuel line clamp kit for Mercury Cougar and Ford Mustang.

Bolts, washers, and spacers kit for installing the rear bumper brackets on any 1969-70 Mercury Cougar or Ford Mustang.

Sold as a Kit as Pictured.

Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds.

Reproduction Fender Extension Stud & Nut Kit for the 67 - 69 Cougar or Mustang

Fits Standard and XR7 Sold as a Kit as Pictured.

Reproduction Firewall Insulation Pad Clip Kit for the 1967 - 1973 Mercury Cougar / Ford Mustang

Fits Standard and XR7 with front bumper guards.

This reproduction hood latch and catch screw and U nut kit fits both the Standard and XR7 and is sold as a kit as pictured.

This reproduction hood latch vertical support screw and U nut kit fits both the Standard and XR7 and is s sold as a kit as pictured.

This is a Mustang kit and it includes 4 screws, 2 metal nuts, 2 self-threading plastic nuts and 2 anti-rattle bumpers as pictured.For Cougar, you need this kit plus 2 more plastic nuts, found here.

Fits Standard and XR7

Fits Standard and XR7 Sold as a Kit as Pictured.

Fits Standard and XR7

We will make sure these original seat belt bolts are damage free. There were minor and major changes almost every year. We also have hundreds of used belts and belt sets that we cannot possibly list all of, so give us a shout for details! *NOTE* Pictured is a complete set of 1969 Torx bolts, spacers, and washers for a coupe. May also have some minimal surface rust.

We will make sure these original seat belt bolts are damage free and rust free. There were minor and major changes almost every year. We also have hundreds of used belts and belt sets that we cannot possibly list all of, so give us a shout for details! 503-463-1130*NOTE* Pictured is a complete set of 1969 Torx bolts, spacers and washers for a coupe.

AMK strut rod hardware kit, course threaded bolts and nuts with cotter pins as shown.

Replaces Ford part # C5ZZ-9673. Fits 1967 289 and 68 -70 390 - 428 cars without Ram Air (C8ZZ-9673).

Fits Standard and XR7 Sold as a Kit as Pictured.

This is our used driver side (left hand) upper rear fender brace. Welds to the upper cowl on any 1969-70 Mercury Cougar and Ford Mustang Ford part number C9ZZ-16A005-A driver side, C9ZZ-16A006-A passenger side.

Used passenger side (right hand) upper rear fender brace that brace visible when you open the door and look in the upper part of the fender void. Welds to the cowl on 1969-70 Mercury Cougar and Ford Mustang. Ford part number C9ZZ-16A006-A passenger side, C9ZZ-16A005-A driver side.

Used for multiple applications. 7/8" from bend to center hole.

Bag of 25 reproduction j-nuts for the front fenders on the Mercury Cougar or Ford Mustang.5/8" from bend to center hole.

Sold as a pair. These often become dislodged due to the force required to be applied after they have rusted in place for decades. Located at the bottoms of the fenders.

Filter / screen for the C6 transmissions, for all 1967-73 and 1967-73 Mercury and Ford. 

Replacement filter for FMX transmissions. Fits all Ford FMX transmissions for any 1969-73 Mercury Cougar or Ford Mustang with that X code FMX transmission. 

Replaceable filter which attaches to original fuel sending unit. Fits 3/8" tube. Replaces Ford part #: D1AZ-9A011-A.

Replacement transmission pan filter and pan gasket kit. For the C-6 (U Code) transmission. Replaces Ford Part Number: C7ZZ-7A098

Replacement transmission pan filter and pan gasket kit. For the FMX (X Code) transmission. Replaces Ford Part Number: C9ZZ-7A098

Reproduction stamped steel firewall for Mercury Cougar and Ford Mustang.Here's our video on front suspension and chassis upgrades.

Pair of reproduction firewall to shock tower braces for the Mercury Cougar or Ford Mustang. These Chinese made units are already painted black, so the only thing you need to do is bolt them on. However, we highly recommend that you get our superior quality used FoMoCo units right here!Replaces Ford part #'s C9ZZ-16A053-A driver side (left hand), C9ZZ-16A052-A passenger side (right hand). ...

Rubber plugs for sealing the holes in the firewall of any 1967-68 Mercury Cougar or Ford Mustang. These plug the firewall holes if you don't have air conditioning or if you have deleted your heater core. Fits 1" body panel holes for all years.Sold as a pair.Original Ford part 377678-S2

Reproduction thick premium firewall insulation pad with clips for the Mercury Cougar or Ford Mustang. These are pre-formed for a perfect fit and appearance and greatly reduced engine noise and heat. The A/C and non A/C versions are one in the same and this unit will fit both A/C and non A/C cars. Unlike cheap paper backed insulation, these quality pads are backed with thick rubber.

Oil filter adapter for all Ford small block engines including 221, 260, 289, 289HiPo, 302, and 351W engines. Ford indicates that this was used 1962-1970. Screws into the engine block. We do not know the threads, but the small side is standard oil filter sized.Ford part number C2OZ-6882-C.

All steel fitting for the lower radiator tank, found on all cars with automatic transmissions. The fine threads go to the radiator and the transmission cooling line screws onto the flared fitting after installation into the radiator. Two needed per car, sold individually. Fits all years 1967-73, and all automatic transmissions. 1/2" threads go to cooling lines. 3/8" threads go into the radiator. *Note - This is an original steel fitting, not a brass reproduction. ...

Concourse Correct FLAPPER DOOR ASSEMBLY for vehicles equipped with ram-air. Includes: door, pivot rod, and 2 retaining clips Fits 1969 390GT and 1970 Boss 302, 351W, 351C. Replaces Ford Part #: C9ZZ-9610-A

Used convertible top flapper stopper. Technically called a "lasting", this is the thin strip of 1/16" thick metal that slides inside the sleeve of your convertible top to keep it from flapping. We will rarely have these on hand, so we've included the dimensions so that you can fabricate your own if needed. 2 required per vehicle.

This flat nut has many uses, most commonly used on the 67 - 68 corral / walking cat headlight eyelid door assembly or the 69 - 70 quarter script. Can be used on anything that has a 3/32" stud. Can be used for many items on a variety of vehicles including the Mustang, Torino, Cyclone etc.Sold individually.

New flat nut, these attach both the shifter seal and shifter dial to the under side of the automatic shifter bezel. Check out our video on rebuilding your shifter below: ...

Good used OEM flex plate for all 69 - 73 Mercury Cougar and Ford Mustang with 302 / 351W engines, and C4 or FMX transmissions. Not for use on a 1968 with 302. The starter ring will show wear and some will choose to replace, others have removed the starter ring and just turned it around so the unused portion of the ring will now contact the starter drive gear. ...

Brand new flex plate for all 1970-71 Mercury and Ford with 429CJ engines, and C6 transmissions. Comes complete with new starter ring gear installed as shown.

These quality mats are made in the USA by Auto Custom Carpets. They are a good fit with an aggressive grip rubber backing. These are heavy mats that will not easily slip out of place or become "wadded up" under your brake pedal. They will hold their form for many years and do more than just enhance the look of your Cougar, they will provide an extra layer of insulation providing an added barrier for heat and sound. Very nice carpet floor mats that make for an ideal gift for that Cougar lover...

These correct floor pan patches are for the 1969-70 convertible and do not have drain plugs like the 1967-68 panels. These are made from a really rigid steel and do not easily bend or dent easily like many of the offshore pans you find on the market. These 20 gauge panels are 24" long and 15 1/4" wide. Great for the person doing a "Correct" restoration on their 1969-70 Cougar / Mustang / Shelby.

New fluorescent needle restoration paint for the gauges in your Mercury Cougar or Ford Mustang. Over the years, the sun has wreaked havoc on your Cat or Pony. This sun damage has also had it's way with the needles on you gauges and washed them out. This true fluorescent paint will not only make your needles look factory fresh, but will also bring back their glow at night. One jar contains 2.25ml worth of paint.

Remanufactured OEM Ford Boss 429 and 429 Cobra Jet manual transmission flywheel. Stamped C9AE-C. New ring gear, resurfaced clutch surface. No visible issues, no discoloration from heat. 1971 Mercury Cougar and Ford Mustang, 1970-71 Ford Torino and Mercury Cyclone and variants. 1969-70 Boss 429. Ford part number C9AE-6375-C.

This is a much cheaper version of the foil sound deadeners and underlays we sell. This particular insulation is basically bubble wrap with two layers of foil on both sides. Good for insulating headliners, floor pans, trunk areas, door panels, kick panels and just about anything else you might want to use it for. This insulation comes in a 48" X 72" roll. Just grab a pair of scissors and cut your shapes. You can use any adhesive you like (contact cement or weatherstrip adhesive,...

Reproduction rubber bumper that mounts to the metal axle snubber on Ford nine inch rear ends on 1969 - 1970 Mercury Cougar and Ford Mustangs. New part with a course threaded stud, also called a pinion bumper. The correct casting number is seen on this rubber axle bumper is C9OA-4906-A, this version has course threads. The version most often seen on the 1967-68 is C3AA-4906-C. It will have a fine threaded mounting stud.