Your cart is empty!
Our shopping cart requires the use of cookies. If you have your cookies disabled, please enable them for our site to place an order. If you have cookies enabled and have added an item to your cart, but you are still seeing this message, that could indicate that the cookie for our shopping cart is corrupted on your computer.You should be able to fix this by either:
Buy Details
Clip or X-washer for attaching the emergency brake lever inside the rear brake drum. Fits 8 and 9 inch rear axles. Literally used on most all Ford products from 1965-73 and likely beyond. Also called a retainer for the parking brake lever pin. The long ears get squeezed with a good set of pliers for attaching. Replaces Ford number 91A-2106.
Delicate clip that attaches to a nail-head stud attached to the firewall. Very functional and visible.
Special clip for attaching the pull cable to the right or left fresh air vent on any 1969-70 Mercury Cougar or Ford Mustang.
Exact copy of the hard to find original. This two piece clip is used to mount gas and/or brake line to floor pans.
Partially dipped clip for attaching the fuel line harness or trunk wiring harness, or fuel line at fuel tank. Found in various places on 1967-70 Mercury Cougar and Ford Mustang.
These retainer clips work for both the windshield and rear window stainless steel mouldings. These are often times rusty so when you are replacing your seal or trim be prepared to replace a few if not all of them. See chart below to determine how many you need for your application. Replaces Ford Part # :C5ZZ-6542413-C, C5ZZ-65423A26-B or C5ZZ-6543413-B.This listing is for a bag of 25 clips. We recommend buying the box of 100 clips to be certain you have enough clips with plenty to spare....
These retainer clips work for both the windshield and rear window stainless steel mouldings. These are often times rusty so when you are replacing your seal or trim be prepared to replace a few if not all of them. See chart below to determine how many you need for your application. Replaces Ford Part # :C5ZZ-6542413-C, C5ZZ-65423A26-B or C5ZZ-6543413-B.This particular clip is used on many Ford cars throughout the 60's and 70's.This listing is for a box of 100 clips. We recommend buying...
These retainer clips work for both the windshield and rear window stainless steel mouldings. These are often times rusty so when you are replacing your seal or trim be prepared to replace a few if not all of them. See chart below to determine how many you need for your application. Replaces Ford Part # :C5ZZ-6542413-C, C5ZZ-65423A26-B or C5ZZ-6543413-B.Sold Individually.We recommend buying the box of 100 clips to be certain you have enough clips with plenty to spare. You'll also save...
Used plastic clip for the Mercury Cougar or Ford Mustang.
Known to have been used on 1969-70 air conditioning boxes to hold a vacuum hose.Used plastic clip for the Mercury Cougar or Ford Mustang.
Used plastic clip for the Mercury Cougar or Ford Mustang
Used plastic clip for the Mercury Cougar or Ford Mustang. Cougar owner Mike B. shares that this clip was also used on 1970 Cobra Jets with Drag Pak option. Used to hold the wiring harness behind the factory oil cooler on the radiator core support.
Used wire loom plastic clip for the Mercury Cougar or Ford Mustang
Non-original style replacement clip for mounting the quarter window regulator arm to the window channel bracket on all 1969-70 Cougar and Mustang coupe and convertibles. This clip will work with either the 1969-early 1970 bracket and the late 1970 bracket. The late 1970 brackets used a unique spring steel clip that seldom is reusable. Sold individually, one each per window.
Partially dipped clip for attaching the seal on top of the radiator core supports. Often times with air conditioning the seals were installed. The factory sometimes used staples, sometimes clips. You would have to investigate your core support for staple holes. 5 clips are typical for attaching the seal. Spread them apart to where it looks equal. Applications: 1967 - 1969 Cougars and Mustangs equipped with the 390 engine, and 1970 Cougars and Mustangs with the 428CJ engine. ...
This is the speedometer cable clip that connects to the firewall and transmission tunnel. Replaces Ford Part # : 373829
New clip for holding a single wire. Often times this clip is used for the trunk light. Also seen under the dash panel on select years. Most likely other locations too from the factory. Panel hole size is 1/4 inch. From the factory one clip was used per car for the trunk light. Sold individually. Replaces Ford part number 382929-S.
Replaces Ford Part # : C9ZZ-6503406Sold Individually.
C9ZZ-6503406-A Front windshield lower moulding retainer clips. 7 clips required per car, sold individually.
Windshield washer hose clip that holds the hose up under the cowl. Concours quality
This clip mounts the actuator shaft to the eyelids. Two required for 1967 - 1968, one required for 1969 - 1970. Same clip holds the windshield wiper motor to the wiper transmission. Replaces Ford part number C4ZB-17450-C.
This clip mounts the actuator shaft to the eyelids. Two required for 1967 - 1968, one required for 1969 - 1970. Same clip holds the windshield wiper motor to the wiper transmission.
New reproduction wire loom clip for the lower radiator core support.
Found on the lower radiator core support. 4 clips needed to attach the wiring harness and the vacuum hoses for the headlight system. Sold Individually. Replaces Ford part # 383104-S.
Found on the lower radiator core support. 4 clips total, attaches the wiring harness and the vacuum hoses for the headlight system.Replaces Ford part # 383104-S.
Secures cable to heater control assembly, heater plenum and heater box. Black oxide bracket with screw.Replaces Ford part number 378897-S
Clips that attach to the dash for mounting the defrost nozzles. Package of 3 clips and nuts. Good for cars with or without A/C. Typically found on 69-73 cars, but will also fit and work on 1967-68 as well.Replaces Ford part number 357849-S100.
Reproduction black plastic clip that goes onto the lower center of the firewall of any 1969-70 Mercury Cougar or Ford Mustang. We have found this to be one of three possible clips on the nail heads for the firewall for attaching wiring or speedometer cables. By far and away the most common clip is the one that looks like black plastic plumbers tape Ford part number 374320-S. This particular clip is the second most common. There is a third clip that is only found on 1969 cars.
Reproduction black plastic clip that goes onto the lower center of the firewall of any 1969 Mercury Cougar or Ford Mustang. We have found this to be one of three possible clips on the nail heads for the firewall for attaching wiring or speedometer cables. By far and away the most common clip is the one that looks like black plastic plumbers tape Ford part number 374320-S. This particular clip is the least common. There is a third clip that is only found on 1969 and 1970 cars.
Used black plastic clip that goes onto the lower center of the firewall of any 1969-70 Mercury Cougar or Ford Mustang. We have found this to be one of three possible clips on the nail heads for the firewall for attaching wiring or speedometer cables. By far and away the most common clip is the one that looks like black plastic plumbers tape Ford part number 374320-S. This particular clip is the second most common. There is a third clip that is only found on 1969 cars.
Used black plastic clip that goes onto the lower center of the firewall of any 1969 Cougar or Mustang. Also found on the back of the instrument cluster on the 71 - 73. We have found this to be one of three possible clips on the nail heads for the firewall for attaching wiring or speedometer cables. By far and away the most common clip is the one that looks like black plastic plumbers tape Ford part number 374320-S. This particular clip is the least common. There is a third clip that is...
Clips or clamps for attaching the 3/8" hard fuel lines to the body of any 1968-73 Mercury Cougar or Ford Mustang. Clips only, save your attaching body bolts. Sold in packages of 4 clips as shown. Will work on 1967 cars if you change to 3/8 lines. 1971-73 Cougar owners can use item 27565 attaching bolts, they are the same as the fuel tank mounting bolts. See related items. Replaces Ford 354663-S8
Pair or reproduction clips used to hold your transmission cooling lines together and keeps them from rattling.
C9ZB-15A006-B Wiring harness, or pigtail that goes from the back of the clock to the main under dash wiring harness. This wiring harness includes the 2 light sockets for the clock illumination. Ford master part number C9ZZ-15A006-A. Fits XR7 and standard Cougars. Fits 1969 Mustang.
Used in conjunction with Ford fan part # C9ZZ-8600-C that is stamped C9ZE-E. Features a parkerized shaft with an integral mounting flange. The aluminum portions are finished with silver cadmium and are mated together with filister head, Phillips machine screws (8) and an additional crimping operation was used to assemble the front and rear housings. The radial curved spring was originally finished in gold cadmium. This assembly stands 2 5/8" tall when set on its front surface, and the distance...
Reproduction thermal fan clutch that fits 1967 - 68 289 engines, 1968 302/390/427/428CJ engines, and 1969 351W engines, all with original Ford thermal cooling fans. Slightly larger in overall diameter, (still fits fine), and retains the correct spacing from radiator. We know that these will fit Mercury Cougar and Ford Mustangs 1967-69. Closest reproduction fan clutch on the market that fits the original and reproduction C8OE-B 7 blade power fan. Hayden fan clutch with an overall height of 2.98...
Closest reproduction fan clutch on the market that fits the original and reproduction C9ZE-E 7 blade power fan. Hayden fan clutch with an overall height of 2.69 inches. Similar design as originals, with thermal activated clutch. Overall diameter is 7.25 inches. The C9ZE-E 7 blade clutch fans were installed on 1969-70 Mercury Cougar and Ford Mustangs as well as 1969 Torino, Cyclone, Ranchero with 428CJ engines. Varies the fan speed with temperature of the air behind the radiator. Engaged (high...
Heavy Duty reproduction fan clutch that fits the original and reproduction C9ZE-E 7 blade power fan. Hayden fan clutch with an overall height of 2.707 inches. About 5/32" taller than our standard duty fan clutch. Please make sure that you have the clearance behind your radiator. Similar design as originals, with thermal activated clutch. Overall diameter is 7.25 inches. The C9ZE-E 7 blade clutch fans were installed on 1969-70 Mercury Cougar and Ford Mustangs as well as 1969 Torino,...
Economy version of the clutch adjusting rod that fits the 1968, 1969, and 1970 Mercury Cougar with the 390GT, 428CJ or the 428SCJ. Replaces Ford Part #: C8ZZ-7521-BR. Can be used on 1967 3 or 4 speed cars with 390 engine, but must use the 1968 clutch fork, see item 13882.
Reproduction premium adjusting rod which includes: 2 Lock Nuts 1 Spacer 1 Retaining Clip Fits the 1968, 1969, and 1970 Mercury Cougar with the 390GT, 428CJ or the 428SCJ. Replaces Ford Part #: C8ZZ-7521-BR. Can be used on 1967 3 or 4 speed cars with 390 engine, but must use the 1968 clutch fork, see item 13882.
Lower clutch rod and adjusting nuts to ensure proper clutch operation. For the Boss 302 and 351. Unless you have your original swivel, also see item 11773. This part goes between the nuts. Replaces Ford Part #: C9OZ-7521-A.
New Old Stock set of brushes only fits the Eaton brand of air compressor clutch. Pitts compressor clutch is the most common one starting in 1969. These are exact reproductions made from the original tooling.Ford part #: C8SZ-2979-A