1969 Ford Mustang

This is the best upgrade tower for your Mustang or Cougar that does not have the factory reinforcement plate. 1969 features the largest plate of all years 1968-70 and will fit perfectly without modification into any year 1967-70. If both of your towers are cracked this is a no brainer, if only one of your towers are cracked then it would look out of place to have one tower that is reinforced and one that was not. No specific part number for this structural front suspension section. For...

Reproduction driver side (left hand) shock tower and apron assembly for Mercury Cougar and Ford Mustang.Here's a little film to help you fortify your flexxy feline!

Reproduction passenger side (right hand) shock tower and apron assembly for Mercury Cougar or Ford Mustang.Here's a little film to help you fortify your flexxy feline!

Solid, undamaged, used driver side (left hand) shock tower brace for Mercury Cougar and Ford Mustangs. Consider our brace kits for the best bang for your buck! Ford part # C9ZZ-16A053-A. *NOTE* Excludes 1969-70 Boss 429.Here's our little film to help you fortify your flexxy feline!

Solid, used, and undamaged passenger side (right hand) shock tower brace for Mercury Cougar and Ford Mustang. Consider our brace kits for the best bang for your hard earned buck! Ford part # C9ZZ-16A052-A. *NOTE* Excludes 1969-70 Boss 429.

Reproduction shock tower brace nuts and bolts for Mercury Cougar and Ford Mustang.Here's our little film to help you fortify your flexxy feline!

Missing some of the hardware used to bolt on your shock tower braces? Here are our reproduction shock tower brace mounting kit for the Mercury Cougar or Ford Mustang.

Used, solid, and undamaged shock tower braces for all 1969-70 Mercury Cougar and most Ford Mustangs. Includes 4 used 7/16"-14 x 1-1/4 inch cowl attaching bolts. Ford part #s C9ZZ-16A053-A driver side (left hand), C9ZZ-16A052-A passenger side (right hand).  *NOTE* Excludes 1969-70 Boss 429. **Installation Tip** These brackets attach 'under' the cowl lip. Here's our little film to help you fortify your flexxy feline! ...

Individual reproduction shock tower cap or coil spring cover in chrome for the Mercury Cougar and Ford Mustang. These are not side specific and two are required per car. Replaces Ford part # C7ZZ-18A017-A.

Individual reproduction shock tower cap or coil spring cover in black for the Mercury Cougar and Ford Mustang. These are not side specific and two are required per car. Replaces Ford part # C7ZZ-18A017-A.

Individual used shock tower cap or coil spring cover in chrome for the Mercury Cougar and Ford Mustang. These are not side specific and two are required per car. While not technically restored original, we offer these to complement our chrome export braces and Monte Carlo bars.  Ford part # C7ZZ-18A017-A.

Used shock tower cap for the Mercury Cougar and Ford Mustang. These are not side specific and two are required per car. These used pieces are superior to the reproductions because they are constructed from thicker metal. Plus, you just can't beat original FoMoCo!Ford part # C7ZZ-18A017-A.

These are exact replacements for the 1964-68 Ford Mustang, but looks similar to the pans for the 1967-68 Mercury Cougar. These floor pans will also fit the 1969-73 Mustang, but the will requires modification to fit properly. 1969-70 cars have different ribbing configurations and 1971-73 cars can use these also. This is a heavy gauged stamped steel floor pan *NOTE* This floor pan has the outside lip bent up which is proper for coupes. Convertibles were bent down. You can either bend it up or...

Driver side (left hand) front seat floor pan.  This pan is cut from the full floor pans in order to save on shipping costs when a customer does not need the entire length pan. Cutting from the Dynacorn full length pans means this will be a quality cut, when compared to other pans on the market. 1967-68 style ribbing, works in 1969-70 and can be modified to fit 1971-73. *NOTE* This floor pan has the outside lip bent down which is proper for coupes, convertibles were bent up. You can either...

These are exact replacements for 1964-68 Ford Mustang, but looks similar to the 1967-68 Mercury Cougar. This floor pan will also fit the 1969-73 Ford Mustang, but 1969-70 cars have different ribbing configurations. To use this pan in 1971-73 cars will require modification. This heavy gauged stamped steel floor pan starts behind the seat platform *NOTE* This floor pan has the outside lip bent down which is proper for coupes, convertibles were bent up. You can either bend it up or remove it and...

Short rubber valve stem and cap for Ford wheels or any steel wheel with a 0.453" hole. Snap in style, sticks up 1-1/4 from wheel surface. These will work with our aftermarket Ford wheels without trim rings. These have the Dill 627 caps. Same as the 1960's cars.

Quarter window upper adjusting screw and nut - used. Mounts to the extension assembly bracket. For all 1969-70 Mercury Cougars and Ford Mustangs. Includes bolt and nut as shown. Fits hard top coupes and convertibles, N/A for fastback or sport roof Mustang.Ford number is 381742-S2 and 376762-S2 for nut.

No damage original bolt. Sold individually, two required per car.

Replaces C9AZ-15447. Sold as a set of four.

*NOTE* EARLY 69's USED THE 2112 MIRROR FOR BOTH PASSENGER AND DRIVER SIDES. LATE 69's USED TWO DIFFERENT SIZES FOR EACH SIDE (2124 for driver side, and 2112 for passenger side). BEFORE ORDERING, PLEASE CHECK YOUR DIMENSIONS AND COMPARE TO OUR LISTINGS. Precision cut replacement lens for any Ford product with sport mirror. This fits any FoMoCo Sport mirror 69 and up. Comes with two round pieces of double sided tape.  Lens measures 4 3/8 X 2 7/8. Do you have questions about installing the...

Empty shell / head / housing only for a passenger side manual adjust mirror. Found on all FoMoCo products utilizing a manual mirror 1969 - 1973. The remote mirror heads found on many 1970's Ford products do not interchange with the manual "Bullet Style" mirrors. Most customers find our reproduction unit to be a better value as it comes with the mirror and mounting hardware. Do you have questions about installing a passenger side mirror or using Riv-Nuts? Have more questions about installing a...

This kit is similar to the original type mounted in every drivers side door. These OEM style Riv-Nuts will be a challenge to install unless you have the special tool. Almost every body shop will have this rivet gun type of tool but here are a couple of ways to tackle the installation without the correct tool. Hole size is 1/4". Replaces Ford Part #: C7AZ-17696. Check out our video below for more info on mirror installation: Still have riv-nut questions? Here are riv-nut answers! ...

Quick disconnect that installs between the sight glass hose and the sight glass to A/C dryer hose. This unit also includes 2 O-rings (Part # L33,D2AZ-19D695-R or YF-368 and Part # H33, D2AZ-19D695-AE or YF-316)Quick Connect (Part # QF3,C1SZ-19B696-A or YF-241 and Part # QM6, C1SZ-19B695-A or YF-252).

Slat or pivot bracket for attaching the #4 rear most bow on a 1969-70 convertible top. Sold individually, one for each side needed for installation. Bushing is normally broken or missing, plan on sourcing or making a replacement bushing for the pivot. Ford part number C9ZZ-7650340-A.

Reproduction power steering control valve sleeve / socket for the Mercury Cougar or Ford Mustang.

New slotted pan head screw for mounting distributor points or condensers. Three total, per single advance Ford distributors. We know that these fit FoMoCo, Autolite and Motorcraft marked distributors 1967-73. These are AMK screws 8-32x9/32". Sold individually, but you likely need 3. 

New phosphate dipped slotted pan head screw for mounting distributor vacuum advances. Two total, per Ford distributor. We know that these fit FoMoCo, Autolite and Motorcraft marked distributors 1967-73. These are AMK screws 8-32x1". Sold individually, you will need 2. 

Reproduction Small Block Engine I.D. Bolt for the  1967 - 1973 Mercury Cougar / 1967 - 1973 Ford MustangSold individually 

Reproduction Small Block Intake Manifold Bolt for the 1968 -1969 Mercury Cougar - 1968 -1969 Ford MustangSold individually 

Thermactor smog hose installation clamps. Fits all Ford and Mercury 1968 S code 390-4V or W code 427-4V engines sold in the US. Additionally fits 1968-70 428 Cobra Jet and Super Cobra Jet engines. Set of clamps, several bolts and spacer as shown. Include bolts for pump pulley, top bolt on pump for adjusting bracket, and pivot bolt and spacer for pump.

Reproduction carburetor spacer plate vacuum port smog plug. Spring clamp included.

Reproduction hardware kit for installing the smog pump on cars with 390 / 427 / 428CJ engines from 1968-70. Including Cougar, Mustang, Torino, Ranchero, Cyclone, etc. Includes spacer, pivot bolt and washer, adjusting bracket bolts.

Set of thermactor smog tubes on any 1968 390GT, 1968 GT-E 427-4V, or 1968-70 428 Cobra Jet engines. Mercury Cougar and Ford Mustang, Torino, Cyclone, Ranchero, etc. These will work with original 390 or 428CJ cylinder heads drilled for air injection smog system from factory. Fits most FE engine applications that used the air pump smog system in 1968 with manual transmission. We also have the ferrules / nuts and other hardware.

Used snap ring that is used to hold the bearing on you the steering shaft. This ring was used on 67 - 78 fixed columns and 70 - 78 tilt columns. Not for use on 67 - 69 tilt columns.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Reproduction black Holley "Sniper" fuel injection conversion carburetor for the 67 - 73 Cougar or Mustang. Upgraded Sniper II also now available! Dual Pattern bolt on carburetor replacement, designed to fit 4150 Flange & Spread Bore manifolds - (Spread Bore Sealing Plate Part #9006 is recommended)Throttle body mounted ECU – no extra boxes to mountSupports up to 650hp with Four 100 Lb/Hr InjectorsOnly 4 Wiring Connections Required! (Battery +, Battery - , Switched Ignition & RPM)Includes...

The #1 EFI conversion system just got better! Introducing Sniper 2 EFI - a self-tuning, easy-to-install, EFI conversion for common 4-barrel (4150 flange) style carburetors. Holley took everything that they learned from the original Sniper EFI system and added 14 new features that will make your EFI conversion more simple, reliable, and modern. Like all Sniper EFI systems, Sniper 2 is designed to work with the Sniper Ecosystem that includes Hyperspark ignition, complete fuel systems, multiple...

Applications all 1969 351 engines, both 351-2V and 351-4V, and 1970 351W-2V engines after 2/2/1970. That is correct, after Feb 1970 the H-code Windsor engined 351's used a 1969 style air cleaner snorkel.The C9OZ-9A626-B snorkel looks the same, but is a bit longer than the 1968 C8AZ-D snorkel. Probably due to the taller deck height of the 351 over the 302 engine, and or the heat shield design. Please note: Wax stat is not tested, nor can we test them, sold as- is. Click on images to enlarge. ...

Quality recreation made from original parts. Decent reproduction, slightly different than the original Ford version. The noticeable difference is the lack of square notch in the slop joint. Ford part of C8OZ-9A626-C. This snorkel comes to you in primer.

For all 1968 through 1970 R and Q code 428CJ and SCJ air cleaners. Snorkel has the opposite jog than 390GT snorkels. This one jogs towards the rear of the engine. Originally this snorkel should have had an ink stamp of C8OF-9A626-A or -B. Ford MPC number C8OZ-9A626-C.

Application would only be for 1969 Boss 302 Eliminators and Boss2 Mustangs.Ford part number C9ZZ-9A626-C.

Air cleaner pre-heater paper hose. Should fit most applications from 1970-73 Mercury Cougar and Ford Mustang with V8 engines. 2 inch inside diameter, we cut these to about 9 inches long. Correct black paper outside, flexible paper tube, kind of like a Slinky. Please verify your needed length, we leave them a bit longer than needed so that they fit more than one application.

Used electrical wiring harness that plugs into the main under dash loom. Two wire harness with light socket and shroud for all 1969-70 Mercury Cougar. This can be made to work on a Mustang. Ford number C9WB-14412-A printed on the wire harness.Fits 69 CougarFits 70 Cougar

Fits both front and rear marker light sockets. Four per vehicle. These are made so that you can splice into your harness. These solve the corroded socket and intermittent light problem.These fit the side marker lights as well as the instrument panel lights. We highly recommend converting these over to LED.Replaces Ford Part #: D0DZ-15434

This new version sequential box works with either standard or plasma LED bulbs NOTE: Although your existing emergency flasher might work just fine with the new sequential unit, it is highly recommended that you also use the same updated electronic sequential flasher in its place to guarantee proper operation. This is a direct fit replacement, just pop open your black plastic box located in the driver side trunk drop off and plug it in. Your January 1970 and newer Cougar will have...

This aluminum backed, tar sound deadener with adhesive is approximately 1/16 of an inch thick and works well behind door panels, at the firewall and under the headliner as a sound, heat and vapor barrier. One sheet required per door. Cut to fit, then remove paper backing to reveal adhesive, and stick in place. Comes in a 36 inch tall by 50 inch wide roll. *NOTE* Use caution when working with this product. The thin sheet of aluminum is quite sharp. We highly recommend using gloves. Before...

HushMat sound deadening and thermal insulation enhances your firewall with the easiest to install sound deadening material. Your vehicle is fun to drive, but the engine gets hot. There is over 200 degrees of heat cooking your firewall and floor pan. Your engine, headers, manifold and exhaust generate tremendous heat that transfers to the metal firewall and floor and this heats up your vehicle interior. It can create a very uncomfortable ride, especially in the summer. This also forces your AC...

Replaces Ford Part #: C9WA-19F514-A