1969 Ford Mustang

Used Under-dash Wiring Harness Plastic Cover / Clip for the 1969 and 1970 Mercury Cougar or Ford Mustang

SUPPLIER IS OUT OF STOCK UNTIL MAY 2024 Used in conjunction with Ford fan part # C9ZZ-8600-C that is stamped C9ZE-E. Features a parkerized shaft with an integral mounting flange. The aluminum portions are finished with silver cadmium and are mated together with filister head, Phillips machine screws (8) and an additional crimping operation was used to assemble the front and rear housings. The radial curved spring was originally finished in gold cadmium. This assembly stands 2 5/8" tall when...

New Old Stock set of brushes only fits the Eaton brand of air compressor clutch. Pitts compressor clutch is the most common one starting in 1969. These are exact reproductions made from the original tooling.Ford part #: C8SZ-2979-A

C9ZZ-7528-A Equalizer bar or "Z" bar for 351 cubic inch Windsor engines and Boss 302 Eliminators with manual transmissions. Both 3 and 4 speed manual transmissions. This is a used part and it will most likely show some wear form previous use.

D0ZZ-7528-C Equalizer bar or "Z" bar for FE big block engines with a manual transmission. Both 3 and 4 speed manual transmissions. This is a used part and it will most likely show some wear form previous use.

C9ZZ-7519-B Good used pedal but these pedals will no doubt show some wear around the clutch rod holes. Three and four speed pedals are all the same. Mustang is the same too.

Made of heavy gauge steel with a satin black painted finish. Replaces Ford Part #: C9ZZ-7535-A.

D1TZ-7600-A New Old Stock service replacement clutch pilot bushing for all 1965-71 390/428/429 engines with manual transmissions. Will fit 1967-71 Mercury Cougar and Ford Mustang with 390-4V, 428CJ, 428SCJ, and 429CJ engines with 4 speed manual transmissions. Fits Fairlane, Cyclone, Torino, Ranchero also.

New old stock stainless clutch pedal pad trim. About 1/8 inches wider that the reproduction version. Replaces Ford Part #: C9ZZ-7B544-A.

Stainless Clutch Pedal Pad Trim. Replaces Ford Part #: C9ZZ-7B544-A.

NOS plastic brackets that screw to your roof and then slide a vinyl colored piece over. Sold individually, two are required per car. Ford part # C8AZ-6229232-A.

NOS white colored coat hooks pair. Reproductions only come in black, these are new in the package. White color started in 1970, off white and parchement 1968-69. Fits 1968-73 Mercury Cougar and Ford everything including that Mustang. Ford Part #: D0AZ-6229024-K.

Powerful oil filled coil that generates 40,000 volts, designed to work with the either of our Pertronix Ignitors. Sold in black or chrome. *Note - This coil is not necessarily needed with the Pertronix Ignitors, the stock Ford coil works fine for most applications.

Made from polyurethane, a bit more rigid and stiffer than our rubber insulators. Sold individually. Two required per vehicle. These are the coil spring insulators available from most Mustang/Cougar suppliers. Replaces Ford Part #: C4DZ-5415-A.

This is an original NOS hot idle compensator for Mercury Cougar or Ford Mustang models with V-8 engine and factory A/C. It is installed in the middle of the hose that connects the PCV valve to the rear of the carburetor spacer. It opens when it reaches a certain temperature which makes the engine run faster when at idle and the A/C is on thereby making the engine run more efficiently. This is an original Ford part that came on air conditioned models from the factory. It was manufactured by...

This listing is for a 3 bolt type upper ball joint, NOS, original Ford Service replacement upper control arm assembly. We have a very hard time keeping these in stock but we keep the listing up as it is good for comparison sake when considering the differences between reproduction and OEM. Keep in mind, service replacement parts often differ slightly from what actually came on the car. Over the years tooling is often replaced or modified and suppliers of things like fasteners often change....

This windshield wiper delay governor mounts to the driver side firewall. To find where this mounts on the firewall

Galvanized three piece replacement tack strips for the 1969 - 1970 Cougar convertible. Over-sized, must be shipped via UPS.

Original used three piece tack strips for the 1969 - 1970 Cougar convertible. Over-sized, must be shipped via UPS.

This pair of reproduction convertible top hooks are beautifully chrome plated and features correct thread size. Looks close to original. These hooks are actually for 71 - 73 Cougars and Mustangs, but will work just fine on the 69 - 70.

C9ZB-7653139-A is the part number for the drivers side, C9ZB-7653138-A for the passenger side. These will often break when one hydraulic lift cylinder malfunctions and the other is still working. This scenario will put the top frame in a bind causing one of these cast parts to break. We carefully inspect these before shipment for cracks, worn areas or corrosion.

C6OE-D and C7AE-F marked fans. Applications: 1. 1968 C code 289-2V engine without air conditioning or heavy duty, or 'extra cooling' option (small radiator). 2. 1969 Boss 302 Eliminator and Mustang. Mustang owners, this 4 blade fan with the part number C6OE-D and (C7AE-F for 1967 and later), is also correct for those K code 289 HiPo engines in both 1966 and 1967. Fan description - 4 blades and 17-1/8 inches in diameter. Ford master part number C6OZ-8600-D. Check out this interesting video...

C9OE-H Application is for all 1969 428SCJ engines with the W code 4.30:1 axle ratio, and some instances it was found on 1970 428 super cobra jet engines. Fan description - 6 blade fixed pitch and 18 inches in diameter. Ford master part number C9OZ-8600-D. Check out this interesting video where they test the efficiency of factory style and aftermarket fans. Spoiler alert: the clutch fans are the most efficient! ...

C9WE-8600-A 5 blade clutch fan for Boss 302 Mercury Cougar Eliminator and Ford Mustang Boss2 cars built before 4-14-1969. 17-1/2 inches in diameter and has the 2-3/8 inch hole for the separate clutch. On page 11-05-01 of the 1969 Ford Shop Manual, volume II it does list this as a 351w Cougar fan. Would like to know if anyone has actually found one of these on a 1969 Cougar with AC. Please contact us if you have any light you can shed on this very rare fan. Click on images to enlarge. Check out...

C9ZE-E Applications: 1. All 1969 428 Cobra Jet with and without air conditioning. 2. 1969 428 Super Cobra Jet with V code 3.91 axles only. 3. 1970 428CJ with air conditioning and some without air conditioning (see your build sheet if available). Fan description - 7 blades and 18-1/4 inches in diameter. Fan does not include thermal fan clutch. Ford master part number C9ZZ-8600-C. Check out this interesting video where they test the efficiency of factory style and aftermarket fans. Spoiler...

C9ZE-6A360-A Very unique part and a component to the 'drag pack' option on the 428SCJ engines. This is an additional counter weight used on conjunction with the SCJ crankshaft, SCJ crankshaft balancer. Ford part number C9ZZ-6359-A.

Original used female half of the factory air conditioning coupler for all 1967-73 liquid line or sight glass hoses. Brass construction, includes the plunger and spring. Also sold as a two piece kit which includes the male and female components. Replaces Ford part number C1SZ-19B596-A.

These were never offered originally but are a popular accessory and more cost efficient than buying a replacement for that unsightly old wheel and tire you took from a Granada in the bone yard!

Reproduction of the very hard to find crossmember for any 67 - 70 Cougar or Mustang with the 390 or 428 engine and the C6 transmission. Replaces Ford Part number C7ZZ-6A023-B

Factory transmission support bracket for use on all 1967 - 1970 Cougars with 390-2V, 390-4V, 427-4V, 428 Cobra Jet engines and C6 automatic transmissions. Ford part number C7ZZ-6A023-B. This part weighs 3.5 pounds and when set on a level surface the height of the mounting hole on the driver side measures 2 3/4" on center and the passenger side is 3 1/2" on center. These "sometimes" will be stamped 390 on the inside.*NOTE* The key identifier on this C-6 unit that separates it from the...

This original part has been reinforced to brace the front frame rails / tie together lower control arm pivots in a superior way to the original design. This design will prevent any camber change in hard cornering. This is not needed for the average Cougar owner but if you are desiring to make your car a "Handling Machine" every bit counts and this is an inexpensive upgrade. These crossmembers are welded in house, and will be unpainted bare metal. This combined with our shock tower...

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Single cylinder head from 1968-70 Mercury Cougar with 428CJ engine with smog holes. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 2.09 and 1.65 inch valves, and the chambers measure out at 73-76cc's. With stock pistons, these heads will net an approximate compression ration of 10.6:1. Basic cylinder head number is 6090. These are the Cobra Jet exhaust manifolds with 16 drilled and tapped exhaust bolt holes. We won't have these in stock...

Plugs for all FE Thermactor cylinder heads (390-4V, 427-4V, 428CJ) and 1968 289 / 302 cylinder heads (casting number C8OE-6090-K) with the Thermactor tube holes. New Old Stock OEM plugs for the elimination of your Thermactor smog system or for replacing the "Home Depot" pipe plugs. Sold individually, a set of is 8 needed, one for each cylinder. Thread pitch 1/2" x 20

Plugs for all FE Thermactor cylinder heads (390-4V, 427-4V, 428CJ) and 1968 289 / 302 cylinder heads (casting number C8OE-6090-K) with the Thermactor tube holes. OEM plugs for the elimination of your Thermactor smog system or for replacing the "Home Depot" pipe plugs. Sold individually, a set of is 8 needed, one for each cylinder.Thread pitch 1/2" x 20 *Note - Export cars that did not require smog had a much shorter version of this plug installed at the factory. The plug shown here would be...

These were installed at the factory on 390 / 427 / 428 equipped cars that were exported to countries that did not require the smog system. They are much shorter than the over the Ford counter service plugs you see in the states that are put on after one removes the smog system.

Used steel lower dash panel for all 1969 Mercury Cougar and Ford Mustang with factory air conditioning. This is a bolt in dash section, ships bare, no brackets included. The easiest way to identify a 69 lower dash from a 70 is that the square cutout for the steering column measures 6 3/8" wide on the 69 and 7" wide on the 1970. Grade A used no pitting no extra holes. Replaces Ford part number C9ZZ-6504320-D.

Here is another great product form Permatex. This decal and adhesive remover removes bumper and window stickers, tar, sap, bugs and other gooey substances. 

Here's the original "stereo" decal for the 69 - 70 door speaker grills. If you want to keep your car as original as possible, these are for you. These decals are made from aluminum, and as you know, they can get pretty flimsy after 45 years. We'll do our best to pick out good ones for you. You can get the sticker repro version here. SOLD INDIVIDUALLY. ...

Set of 5 reproduction firewall inspection decals. During final inspection, these decals where placed in different locations on the firewall / cowl area and one P decal between the weatherstrip and dash pad inside the drivers door jam. This decal set has the assembly line inspectors names stamped on them. These decals would have been used on cars equipped with Boss 302 and BOSS 429 engines.

Used switch for the rear defog or defogger fan on any 1969 Mercury Cougar, 1969 Standard Cougar, and 1969-70 Mustang coupe or hardtop. Original switch with attached wiring harness. Tested and working two speed switch. Comes as shown with chrome knob marked "DEFOG". Some examples may have minor pits in the chrome knob. Wiring marked C9WA-18C498-A. Excludes all convertible models and Mustang fast backs.Replaces Ford part number C9ZZ-18578-A.*Note - is not technically correct for 1970 Mercury...

New old stock deluxe shifter handle in light aqua. Perfect condition, no cracks in the plastic. No release button or set screw included. NOS Ford part number C8OZ-7213-AQ The 67 version was actually a little different. Check out our video on rebuilding your shifter below: ...

Original dipstick or in Ford speak "Indicator - Oil Level" for FMX automatic transmissions. Application for 1969 - 1972 Mercury Cougar and Ford Mustang with 351 and FMX automatic transmissions, code "X" on your door data plate. Sometime during 1972 Ford changed to C9AP-7A020-C. Same dip stick, but with a longer handle.Ford master part number C9OZ-7A020-A, Ford casting # C9OP-7A020-A.

Original dipstick tube. Application 1967 - 1969 Mercury Cougar or Ford Mustang with C6 automatic transmissions, code "U" on your door data plate. Ford master part number C8ZZ-7A228-A.

Original dipstick tube. Application 1969 Mercury Cougar or Ford Mustang with FMX automatic transmissions, code "X" on your door data plate. These are identified by being painted blue. Ford part # C9OZ-7A228-B.

As seen in our YouTube video, this is a representation of the used, rebuilt and reproduction parts that we recommend you purchase to convert to disc brakes. If you do purchase this package we will insist on speaking with you prior to shipping as you may want to substitute parts based on what year your car is, manual or automatic and what style booster you prefer. Also know that if your car already has power drum brakes we will be able to reduce the price substantially as no booster or pedal...

Used core distributor for 1969 Mercury Cougar and Ford Mustang with M code 351-4V engines with 3 or 4 speed stick. Core distributors will have correct stamping of C9OF-N. Original Ford part number C9OF-12127-N.

Used core distributor for 1969 Mercury Cougar and Ford Mustang with M code 351-4V and automatic transmission. Core distributors will have correct stamping of C9OF-Z. Original Ford part number C9OF-12127-Z.