1969 Ford Mustang

Mercury Cougar and Ford Mustang AM-8 track Motorola manufactured radio. May or may not work and wiring plugs may be cut. Great radio for reconditioning and often times the 8 track feature only needs a drive belt to work perfectly again. Ford part # C9ZA-19A242. *TRIVIA* The window sticker price for this option in 1969 was $195.60. Are you going to install this unit yourself? The first issue of Legendary Cougar Magazine has a great how to article that will help you in your journey to musical...

Mercury Cougar and Ford Mustang, Bendix manufactured, factory installed AM/FM stereo radio. Tested and found to work well. Knobs sold separately. Ford part # C9ZA-19A241 or 9FBZ-A. Are you going to install this unit yourself? The first issue of Legendary Cougar Magazine has a great how to article that will help you in your journey to musical bliss. You can get it here! ...

This Autolite capacitor is stamped with part number C6OA-18832-A. It attaches to one of the lugs on the voltage regulator, bullet lead plugs into wiring harness. Sometimes called a radio ignition interference suppressor. About 1-15/16" inches long. This is one of those small detail items that judges like. All Ford and Mercury vehicles from 1966-1971 used this "Autolite" marked capacitor when a radio was installed by the factory. Starting in 1972 there is a Motorcraft version which has a...

This rubber steering coupler for your fixed column, commonly referred to as a "rag joint", connects the steering shaft to the input shaft on the steering box. This is a multi-fit part that covers many years of FoMoCo products, so you will have a couple of parts left over upon completion. Will require a grinder to remove from your old steering coupler fittings. Replaces factory steering coupler on 1967 - 1973 cars. Early 1967 Mustangs do not have coupler on fixed columns. Replaces Ford part #...

Steering column to steering box coupler, also known as a 'rag' joint. Used on 1967 1968 1969 1970 Cougar tilt columns, differs greatly from the fixed column version in that is has a "D" shaped fitting on the column side. Good used condition, supplied with one, 12 point attaching bolt. You will need to reuse your existing 12 point bolt for the other end or purchase a second one. *NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this service is...

NOS power steering ram cylinder dated 6H25 or August 25, 1966. This one is date coded for a very early built 1967 Mercury Cougar or Ford Mustang, including Shelby GT350 and GT500. Bendix manufactured, shows a paint marking and gold cadmium? nut and band. Still has the plastic plugs and cardboard protection on the threaded shaft and drag link stud. Seals presumed to be good, but no guarantees.

New old stock ashtray for any 1969-70 Mercury Cougar or Ford Mustang with factory console. This is the rear ash tray. Ford part number C8AZ-6262876-A.

Used rear console support bracket for the 69 Cougar or Mustang. Mounts under the leading edge of the storage compartment under the console.NOTE - 69 and 70 used different brackets

This is a grade 'A' used mirror assembly with no UV damage and has had the mirror lens "re-silvered". Keep in mind a restored lens that is decades old will look good when finished but almost never flawless as the surface of the glass will usually have light scratches and often faint spotting on the backside from previous water damage / staining. Sold outright, no core required. NOTE: Pictured is black, but if you would like a specific color other than black please mention it in the...

Due to time constraints, we can no longer offer the service of having your own mirror restored, this is now an exchange based service only.Any mention of it in the video below is outdated, please disregard. Restored 1967 early style larger rectangular rear view mirror lens for the Mercury Cougar or Ford Mustang. Unlike our full price restored lenses, these require no core. These lenses look good at first, but if you look close you may see a scratch, tiny chip around the perimeter or...

Due to time constraints, we can no longer offer the service of having your own mirror restored, this is now an exchange based service only.Any mention of it in the video below is outdated, please disregard. Restored rear view mirror lens for the 68 - 73 Mercury Cougar or Ford Mustang. Unlike our full price restored lenses, these require no core. These lenses look good at first, but if you look close you may see a scratch, tiny chip around the perimeter or discoloration in the lens. If your...

Professional strength adhesive for attaching your rearview mirror bracket to your windshield. Good for 1968 - 1973 Cougars and Mustangs. 1967's Didn't have the bracket attached to the windshield.

Basic FMX transmission rebuild kit. Kit includes gaskets, seals, bands, filter, modulator, everything as shown. Fits all Ford FMX transmissions for any 1969-73 Mercury Cougar or Ford Mustang with that X code FMX transmission. Quality kit, same as supplied to professional shops. 

1969 Ford four speed shifter rebuild kit. Kit includes tension spring, steel clip, threaded machined shaft, pair of roll pins, pair of dowel pins, and two bolts. Information indicates that all 1969 4 speed shifters are the same across all car lines and for all engines. Link to the Ford shifter linkage expert. Check out our video on rebuilding your shifter below: ...

Core regulator assembly or brain box for factory speed control on a early 1968-69 Mercury Cougar or Ford Mustang. This is the Perfect Circle regulator assembly. Basic Ford part number is 9D757, research has not turned up the complete Ford number possibly C8VY-9D757-A. Core grade, most likely will need servicing or repair. Bare unit, no brackets, wiring or cables. *Note - We do not have the tools or know how to test this unit. 

This pair of plates cut from 11 gauge steel (1/8") are designed to be welded onto the front crossmember that braces the front frame rails and ties together the lower control arm pivots in a superior way to the original design. When welded onto the front crossmember properly, these plates will prevent any camber change in hard cornering. This is not needed for the average Cougar owner, but if you are desiring to make your car a "Handling Machine", every bit counts. This combined with our shock...

NOS seat belt warning light relay for most Ford Lincoln and Mercury cars starting in 1967 until sometime in 1972 when a Motorcraft version of this exact relay was produced. This is a timed relay that allows several seconds of illumination to your seat belt warning light. Ford Part number C7AB-10B924-B1, Ford Service part number D1AZ-10B924-A or D2AB-10B924-AA.

New old stock tilt / tilt away steering column lock relay for the Mercury Cougar or Ford Mustang. Keep in mind we have a reproduction substitution for this part. This unit can be identified with the bend in the bracket compared to the 1967 relay which is straight.  Ford part # C8ZA-3E553-A. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.co...

Ford OEM kit for rebuilding your power steering control valve on any 1962-70 Ford or Mercury. All parts in photo are included. We also have the complete rebuild kit available.  NOS power steering control valve repair kit.  Ford part number C2AZ-3A553-A.

Good used metal strip that fastens the weatherstrip to the bottom side of the header bow. Keep in mind we have (almost) every single used part related to the 69-73 Convertible Cougar and convertible Ford Mustang / Shelby in stock at all times.

Nice reproduction clip for attaching the speedometer cable onto 3 and 4 speed 1967-70 Mercury Cougar and Ford Mustangs. Mounts to the firewall.

Larger sized retainer that screws to upper front lip near the quarter glass on all 1969-70 Mercury Cougar hardtops and 1970 Ford Mustang coupes. Ford lists this part as: Retainer - quarter trim panel rear. We see these sometimes installed in the front position at the top of the interior quarter panel next to the window glass, mostly the front position is empty or the factory installed two of the smaller retainers. This retainer helps the top section of the soft trim panels from rattling. The...

This clip secures the clutch pedal rod end as it comes through the clutch pedal hanger.C8AZ-2B277-A

NOS retainer / friction clips that replace broken injected plastic shaft retainers on fixed or tilt steering collapsible columns on most FoMoCo products starting in 1968 and through the 70's. These installs on the upper piece of what Ford called the Steering Column Shaft Assembly, also known as the inner steering column collapsible shaft.  The Steering Column Shaft Assembly is the 2 piece shaft that connects the steering wheel to the rag joint. The upper piece of this shaft...

Good grade "A" used nut with minimal scratches from removal process. The originals have deeper grooves and have a better luster on the chrome than the reproductions. This is a one year only design. Don't forget to check out our special tool used to remove and install this nut.

This fits behind the door panel and is needed to install your remote mirror correctly.*NOTE*1969 Cougar owners do not need this part as it is built in the the chromed plastic, rectangular bezel on the door panel.

Reproduction hold down clamp rivet for the 67 - 73 Cougar or Mustang. This rivet holds the clip / clamp onto the distributor. Sold individually, 2 per car.

If your original is pitted or has come apart this will be a clean, crack free used replacement that will easily snap in place. We have a reproduction, but the finish is rougher, as shown in the comparison photo. There were originally two versions of this switch: the one shown with both round contact points in plastic, and another which had one in metal.

Used Rod for the bell crank accelerator for 1969 Mercury Cougar and Ford Mustang with speed control. The Rod fits between the Servo and Bell Crank. Ford number may be C9ZZ-9D774-A, just a guess.Ford part number 9D774.

This rod was used on the Bendix brand booster (crimped together case). It measures 5 3/4" long. Used on many Ford products including Torino, Cyclone, Ranchero, Cobra, Fairlane and others. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot...

This is a modern upgrade to your manual transmission cars. It replaces the bushing that is in the crank shaft. Supports the tip of the input shaft of the transmission. Quality part with roller bearings on the inside, fits small block only.Replaces Ford Part #: C7AZ-7600-A.

New RTV  oil resistant, high temperature, Ultra Black gasket maker for use on the Mercury or Ford. It's no mistake that Ultra Black has become an automotive industry standard. It's low odor, flexible, non-corrosive, vibration resistant, oil resistant, heat resistant, fast curing formula cannot be beat. Great for use on any surface that experiences high heat and oil like the valve cover gaskets.

New Permatex RTV gasket dissolver, good for all makes, models, and years. Use this stuff when you want to remove any remnants of those old worn out silicone gaskets made with any of the common gasket makers. Handy item to have on hand so you dont have to keep using your putty knife or screwdriver! 

The 69-73 looks the same as the earlier version once installed but the casting number will read C3AA-4906-C on the early unit and C9OA-4906-A on the 1969-73 version. We have found a few rubber bumpers marked D3Z... very few. See other listing for that one..

Concours? almost, these are stainless steel screws with the wax tipped coating like the originals, for installing the door sill plates. The wax was deemed necessary by the Ford Motor Co. as a seal. These can be used on all years 1967-73 Mercury Cougar, Ford Mustang and most all other Ford, Mercury, Lincoln cars of the era. Works well with any of the reproduction sill plates, these were really made to be used with the premium reproduction sill plates in stainless steel. 1967-68 Cougar and...

Concours? almost, these are stainless steel screws with the wax tipped coating like the originals, for installing the door sill plates. The wax was deemed necessary by the Ford Motor Co. as a seal. These can be used on all years 1967-73 Mercury Cougar, Ford Mustang and most all other Ford, Mercury, Lincoln cars of the era. Works well with any of the reproduction sill plates, these were really made to be used with the premium reproduction sill plates in stainless steel. 1967-68 Cougar and...

Sold individually, original glove box cable screw with shoulder. For any 1967-70 Mercury Cougar or Ford Mustang. Probably many other Ford and Mercury cars also.Ford part number 379202-S2.

Used in the latter part of 1967 and all of 1968 and 1969 to fasten the upper column cover to the column. Early 1967 used a chrome version of this screw.

C6OZ-7A533-C. Clutch Pedal Rod To Firewall Seal. Much better than repro. Also fits 1966 Mustang / Fairlane / Comet and others.

Replacement seal with boot for all 1969-73 FMX and 1967-73 C6 transmissions. Tail shaft and slip yoke seal. 

If your power steering control valve unit is in good working condition but seems to be leaking, this seal kit may be all it takes to correct the problem. Keep in mind many of the high mile control valves in circulation are worn beyond factory tolerances and are not easily rebuilt. Our re-manufactured units are a great solution if this is the case. We also have the complete rebuild kit available.  ...

Driver side seat back release assembly, can me used for a conversion of 1970 high-backed seat backs for use in 1969 Mercury Cougar Eliminator and Ford Mustang Mach 1. This assembly has the release lever mounted nearly at shoulder level, factory 1970 high backs have the latch release at the hinge. This is a sneaky way to 'create' the factory 1969 high backed seats from 1970 seat backs. Comes with all hardware as shown. See picture for locating the three holes required for installation in a 1970...

Driver side seat back release catch for the 68 - 70 Cougar or Mustang.

These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included!Sold individually

Now you can replace this original part, which is commonly stripped out, with a nice reproduction. Must be welded to floor pan. 6 total per car, 2 inboard in the transmission tunnel, and 4 on the rear seat pans. The front outboard anchors are part of the rocker rails. Rectangular shaped like the 1967-73 cars. We have noticed that the last generation 1971-73 Cougars had 4 round shaped plates in the rear floors. Same threads, all work the same. These were pretty much used on all Ford...

Both deluxe and standard use the same retractor in 1968 - 1969 and left is the same design as right. Grade "A" retractors will show no fading or cracks on the holster / retractor cover, good chrome buckle and may even still have the date code tag sewn in place. For no extra charge we will attempt to locate the correct date code for your car if you provide your cars build date. Keep in mind no retractor was used in convertibles until 1972, only a lap belt. Check out our video "All about seat...

This is an example of the best grade A set we can come up with. This was a standard set that was converted to deluxe by installing the reproduction chrome buckle bezels. The mounting hardware is sold separate. Keep in mind we have over 200 complete sets of belts for 1967-73 in many colors and conditions. We will also sell individual belts and related parts. NOTE: The seat belts you receive will most likely not have intact tags. Check out our video "All about seat belts" below. ...

This is an example of the best set we can come up with. This was a standard set that was converted to deluxe by installing the reproduction chrome buckle bezels. The mounting hardware is sold separate. Keep in mind we have over 200 complete sets of belts for 1967-73 in many colors and conditions. We will also sell individual belts and related parts. NOTE: The seat belts you receive will most likely not have intact tags. Check out our video "All about seat belts" below. ...