1969 Ford Mustang

If your power steering control valve unit is in good working condition but seems to be leaking, this seal kit may be all it takes to correct the problem. Keep in mind many of the high mile control valves in circulation are worn beyond factory tolerances and are not easily rebuilt. Our re-manufactured units are a great solution if this is the case. We also have the complete rebuild kit available.  ...

New and improved reproduction bottom of the door seal for the 1967 - 1970 Mercury Cougar or Ford Mustang. Unlike previous versions, these are now made with denser material and are much more rigid. They measure 38" for 1967 -1968 and 41" for 1969-70 so you will have to trim them down if you have a 1967-68. One of the most common missing parts on a 1967-70 Mustang or Cougar today is the lower weatherstrip seals on the doors. These seals were added to cars to keep dirt and moisture from entering...

Driver side seat back release assembly, can me used for a conversion of 1970 high-backed seat backs for use in 1969 Mercury Cougar Eliminator and Ford Mustang Mach 1. This assembly has the release lever mounted nearly at shoulder level, factory 1970 high backs have the latch release at the hinge. This is a sneaky way to 'create' the factory 1969 high backed seats from 1970 seat backs. Comes with all hardware as shown. See picture for locating the three holes required for installation in a 1970...

Driver side seat back release catch for the 68 - 70 Cougar or Mustang.

These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included!Sold individually

Now you can replace this original part, which is commonly stripped out, with a nice reproduction. Must be welded to floor pan. 6 total per car, 2 inboard in the transmission tunnel, and 4 on the rear seat pans. The front outboard anchors are part of the rocker rails. Rectangular shaped like the 1967-73 cars. We have noticed that the last generation 1971-73 Cougars had 4 round shaped plates in the rear floors. Same threads, all work the same. These were pretty much used on all Ford...

Both deluxe and standard use the same retractor in 1968 - 1969 and left is the same design as right. Grade "A" retractors will show no fading or cracks on the holster / retractor cover, good chrome buckle and may even still have the date code tag sewn in place. For no extra charge we will attempt to locate the correct date code for your car if you provide your cars build date. Keep in mind no retractor was used in convertibles until 1972, only a lap belt. Check out our video "All about seat...

This is an example of the best grade A set we can come up with. This was a standard set that was converted to deluxe by installing the reproduction chrome buckle bezels. The mounting hardware is sold separate. Keep in mind we have over 200 complete sets of belts for 1967-73 in many colors and conditions. We will also sell individual belts and related parts. NOTE: The seat belts you receive will most likely not have intact tags. Check out our video "All about seat belts" below. ...

This is an example of the best set we can come up with. This was a standard set that was converted to deluxe by installing the reproduction chrome buckle bezels. The mounting hardware is sold separate. Keep in mind we have over 200 complete sets of belts for 1967-73 in many colors and conditions. We will also sell individual belts and related parts. NOTE: The seat belts you receive will most likely not have intact tags. Check out our video "All about seat belts" below. ...

This is a complete set of Deluxe (chrome bands on buckles) safety belts removed from a 1969 hardtop minus torx bolt hardware. The set consists of two front retractors (they are not side specific) that measure 22" fully extended tip to tip, four lap belts bonded in pairs with the shoulder portion measuring 45" and the lap belt portion measuring 30" total length. The two male rear belts measure 20" and mount next to the rear interior panels and the female buckle side measures 36" fully extended....

This dealer option was installed for people who were not comfortable with the height of their seats. This same kit was used on many intermediate Ford Products from 1965-1970. One kit does one bucket seat or one bench seat. Ford part # C6OZ-6362016-A. Click on images to enlarge. The screw on clips were included in the kit so the spacer would stay in place as the seat was guided into the four holes in the seat riser. Often these clips are cracked or missing and we cannot guarantee all four will...

New Old Stock Ford bracket with attaching parts. Repairs the Driver Side bucket inner seat pivot. Ford service replacement part.A very common breaking point on the upper portion of the driver side inner, can now be easily repaired. If you have a '68 or '69 Cougar or Mustang, check the driver seat back attachment for the recall / campaign fix. There should be a heavy bracket secured by a bolt over the seat back attachment. There is a heavy pin on this bracket that forms the pivot for the seat...

New Old Stock Ford bracket with attaching parts. Repairs the Passenger Side bucket inner seat pivot. Ford service replacement part D7ZZ-69618C47-A. A very common breaking point on the upper portion of the driver side inner, can now be easily repaired. If you have a '68 or '69 Cougar or Mustang, check the driver seat back attachment for the recall / campaign fix. There should be a heavy bracket secured by a bolt over the seat back attachment. There is a heavy pin on this bracket that forms the...

Used driver side outer bucket seat black hinge cover, for any 1970 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. The factory change the end that goes under the upholstery in 1970. Limited to supply on hand. Ford was slow about updating the casting number on some of these, some will have a C8ZB-6561695 number possibly. Ford number D0ZB-6561695. ...

Reproduction chrome knob for the seat track release to adjust the position of the seat. This knob is an exact replica of the original and installs with a hidden set screw. A simple way to dress up your interior while maintaining a stock appearance. Made from chrome plated die cast metal.Sold individually. Replaces Ford Part #: C5AZ-6261753-BA.

We have a VERY limited supply of seat tracks that are taken from cars that have never been in the weather. These should need nothing but cleaning and lubrication. Fits all 1967-70 Mercury Cougar including convertible, and 1965-70 Ford Mustang. Used kit includes C5ZZ-6561704-F, C5ZZ-6561705-F, and C5ZZ-6561726-A. Note that many of the 67's do not have the rectangular plate in place as seen here. We have a separate listing for those if you want to match your existing version. ...

Good used part that will need to be cleaned up and painted if you want it to look perfect but will be ready to use as is. Functionally and structurally perfect, cosmetically average. Good used part that will need to be cleaned up and painted if you want it to look perfect but will be ready to use as is. Ford master part number C7ZZ-6561705-A. Application 1967-69 Mercury Cougar and Ford Mustang only.

Good used part that will need to be cleaned up and painted if you want it to look perfect but will be ready to use as is. Functionally and structurally perfect, cosmetically average. Clean original FoMoCo parts like these in the end are almost always a better choice in the end even if they do require some elbow grease to look as new. There are minor differences between the years, select the correct year for your application and we will be sure to choose the correct style from our large...

1967-69 Mercury Cougar and 1965 - 1969 Ford Mustang shifter handle for automatic transmissions. We find this smaller early style chromed shifter handle in lots of 1969 Cougars, we believe that there was a transition period before the C8OZ-7213-A was used. This is the base model shifter handle with both black buttons, and set screws. Ford part numbers C5ZZ-7213-F, C5ZZ-7C488-M, C5ZZ-7C488-D. Click on images to enlarge. Check out our video on rebuilding your shifter below: ...

1969-72 Mercury Cougar and Ford Mustang shifter handle and buttons, for automatic transmissions. This is the base model shifter handle with correct black buttons, and set screws. Deluxe shifters were larger and had simulated leather wrapping. Ford part numbers C8OZ-7213-A, C8ZZ-7C488-A, and C8ZZ-7C488-B. Click on image to enlarge. Check out our video on rebuilding your shifter below: ...

Fragile black plastic channel selection button that often gets broken. Requires advanced skills to remove and replace.

New old stock 1968-72 (works on 1967) Mercury Cougar XR7 and Ford Mustang Deluxe shifter button for automatic transmissions. This is for all cars with body type 65B, 76B, and Grande. This is for the deluxe model shifter. New old stock, NOS. Ford part number C8OZ-7C488-A. Check out our video on rebuilding your shifter below: ...

Big bell shaped oil pressure sending unit for 1967-73 Mercury XR7 and 1967-73 Ford Mustang with actual oil pressure gauges instead of idiot light for the oil pressure. *Note - this pressure switch does use the press on wiring boot. Please check your wiring harness for the proper connector. This oil pressure sending unit also fits the following cars that have analog oil pressure gauges: 1969-71 Continental MKIII, Thunderbird 1965-71.Replaced Ford part # C9ZZ-9278-A Check out the video...

Brass sensor that screws into intake manifold and activates temperature gauge in dash. Replaces Ford Part #: C6DZ-10884-B (SW-552) or C9WY-10884-A (SW-888)*. Temp Sender Switch Temp Rating : 15.2-19 Ohms Resistance At 220 Deg F Temperature Switch Thread Size : 3/8" x 18 NPT * - The 1969 351 Windsor temperature sending unit has been discontinued. Most manufacturers list the 1968 302 temperature sending unit as the closest replacement.Check out the video below on our new gauge tester: ...

NOS new old stock Motorcraft water temperature sending unit, fits Ford 289, 302, 390, 427, 428CJ. 260° stamped, for Mercury Cougar 1967-69, and Ford Mustang 1966-69.  Ford number C6DZ-10884-B. *Note - these are specifically NOT for 1969 351W. Ford had a unique part number for that one engine.... and we don't stock that one. Sorry. Check out the video below on our new gauge tester: Check out our video on replacing the fuel system on a '68 Cougar! ...

Used Autolite water temperature sending unit, fits Ford 289, 302, 390, 427, 428CJ. 260° stamped, for Mercury Cougar 1967-69, and Ford Mustang 1966-69.  Ford number C6DZ-10884-B. *Note - these are specifically NOT for 1969 351W. Ford had a unique part number for that one engine.... and we don't stock that one. Sorry. Check out the video below on our new gauge tester: Check out our video on replacing the fuel system on a '68 Cougar! ...

This A/C suction service valve fits on top of the compressor and is an exact copy of the original unit.Good for R-134A, but still compatible with R-12.Fitting sizes:Male end 7/8"Female end 9/16"

Used Servo Assembly for 1969 Mercury Cougar and Ford Mustang with speed control. The Servo is the rubber bellows. Part of the accelerator pedal assembly in the passenger compartment.Ford part number C9ZZ-9C735-A.

Shaft or rod for the heater core damper door on any 1969-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The heater damper door allows air to pass over the heater core in the fiber glass A/C box. Part cleaned for photograph, normally will ship 'as removed'. Inspected for damage or weakness of the metal. Shaft only, door not included, but available. See related parts.Replaces Ford part number C9ZZ-19C774-B.*Note will not work in 1967-68 A/C boxes. ...

Used plastic sheath that covers the bolted buckle end of where your shoulder belt attaches to the roof section of your car. Sometimes when removing the bolt from your shoulder belt, this sheath will tear if the plastic has become stiffened. Although it does not affect it's usage, sometimes it's best to simply replace it.  NOTE: To remove this sheath, you will have to pull some slack from the seat belt up through the opening at the top in order to push up on the sheath to access the...

This 1969-70 Mercury Cougar and Ford Mustang shield, was installed at the factory to protect the heater motor from being damaged when the Big Block 390 / 428CJ's were being dropped in. As noted in the factory assembly manuals we sell, they were supposed to be removed once the motor was in place. We have found that more often than not they were left in place as it was probably too time consuming to remove them. Technically they should not be in place on a concours car but practically...

Mercury Cougar shift handles never came covered in real leather from the factory but what a cool upgrade! We sell a lot of these and the feedback has been great. We also carry the original plastic covered (simulated leather) reproduction XR7 shift handles in several colors but this real leather handle comes in black only.

Used to block light from escaping around shifter stem seal. Fits 1969-73 Mercury Cougar and Ford Mustang as well as 1971+ Pinto, Bobcat, Maverick, and Comet with floor shift automatic transmissions. The 90 degree notched portion straddles the set screw on the cast light housing. Most shifters (almost all) we see do not have this part in place any longer. Ford part number C9ZZ-7E130-A.Note: This fits perfectly on the shifters we have tried, but several customers have commented that it was too...

This keeper affixes to the top of the plastic indicator arrow.  Screws included. Check out our video on rebuilding your shifter below: ...

Very hard to find 69 - 70 Shelby / 68 - 69 Cougar 4 speed shifter knob. These very rarely come up for sale used and when they do they are expensive. Correct for 1968-69 Mercury Cougar XR7 and 1969-70 Ford Shelby Mustang, all with 4 speed manual transmissions. Ford part number C8WY-7113-C. Check out our video on rebuilding your shifter below: ...

Clean no nonsense look. 12MM Threads. Check out our video on rebuilding your shifter below:

Used lamp diffuser for all 1969-73 Mercury Cougar and Ford Mustangs. Note the comparison picture. The reproduction is a shade or two lighter than original. The complete Ford part number is not available, the basic part number for this item is 15811. Check out our video on rebuilding your shifter below: ...

3 Speed manual transmission shift control assembly for any 1969 Cougar or Mustang. Control assembly only, no rods or chrome lever. C9OZ-7400-B Check out our video on rebuilding your shifter below: ...

C9OZ-7400-B3Assembly Factory 3 Speed manual transmission shift control assembly for any 1969 Mercury Cougar or Ford Mustang. Includes shifter mechanism, shift rods, and shift lever. All in used condition. The Ford MPC states that this same shifter was used on 6 cylinder Mustangs and all V8 Mustangs and Cougars as large as the 390-4V engine. Check out our video on rebuilding your shifter below: ...

C9OZ-7400-AAssembly 4 Speed manual transmission shift control assembly for any 1969 Mercury Cougar or Ford Mustang. Includes shifter mechanism, shift rods, and shift lever. All in used condition. The Ford MPC states that this same shifter was used on all V8 Mustangs and Cougars. Check out our video on rebuilding your shifter below: ...

Used automatic shifter bezel / indicator assembly for all Mercury Cougar and Ford Mustang with or without consoles. These are the best used ones from our inventory. These will have some minor issues with the chrome plating and most often need some detailing on the black pebble grain. Consider also purchasing a new seal, shift indicator lenses may or may not meet your requiements. Doesn't meet your requirements? We have very nice quality 1969-70 reproduction shift plate bezels also available....

Metal core base as original, correct texture. If you have a 1970 with a Hurst four speed then the one with the rectangular hole is correct for the Hurst shifter. Replaces Ford part # C9ZZ-7277-A. Check out our video on rebuilding your shifter below: ...

Stunning quality and far less likely to crack than the originals. The 67 version was actually a little different than 68 - 73 but you would have to look close to see the difference. Check out our video on rebuilding your shifter below: ...

Stunning quality and far less likely to crack than the originals. The 67 version was actually a little different than 68 - 73 but you would have to look close to see the difference. Check out our video on rebuilding your shifter below: ...

C9ZZ-7210-A Shift lever for all 1969 Mercury Cougar and Ford Mustangs. Manual 3 speed only, 4 speeds are different. *Note - Must be used with Trunion C9OZ-7210-B, sold separately. Check out our video on rebuilding your shifter below: ...

C9ZZ-7210-B 4 Speed shifter lever for any 1969 Mercury Cougar and Ford Mustang with V-8 engines. *Note - Must be used with Trunion C9AZ-7210-J, sold separately. Check out our video on rebuilding your shifter below: ...

Used 4 speed manual transmission shift control assembly for the Mercury Cougar or Ford Mustang.Ford part # C9OZ-7400-A. Check out our video on rebuilding your shifter below: ...

Adapter plate for mounting the 3 or 4 speed shifter control assembly to the Top Loader transmission.Ford part # C9ZZ-7E046-A. Check out our video on rebuilding your shifter below: ...