1969 Ford Mustang

C9OZ-7210-B "U" shaped bracket that attaches the 3 speed shift lever to the shifter control assembly. For use on all 1969 Mercury Cougar and Ford Mustangs with the 3 speed shift lever. Bottom bracket only, called a Trunion (see illustration). *Note - Must be used with 3 speed shift lever C9ZZ-7210-A. Check out our video on rebuilding your shifter below: ...

C9AZ-7210-J "U" shaped bracket that attaches the 4 speed shift lever to the shifter control assembly. For use on all 1969 Mercury Cougar and Ford Mustangs with the 4 speed shift lever. Bottom bracket only, called a Trunion (see illustration). *Note - Must be used with 4 speed shift lever C9ZZ-7210-B.

Passenger side (right hand) front seat floor pan. This pan is cut from the full floor pans in order to save on shipping costs when a customer does not need the entire length pan. Cutting from the Dynacorn full length pans means this will be a quality cut, when compared to other pans on the market.   1967-68 style ribbing, works in 1969-70 and can be modified to fit 1971-73. *NOTE* This floor pan has the outside lip bent down which is proper for coupes, convertibles were bent up....

If your are missing your factory Riv-Nuts, or you are installing a passenger side mirror, these are a very easy to use alternative to the metal riv-nuts we offer. Another good application for these is when your existing mirror mounting holes are "hogged out" these slightly over sized inserts are just the ticket. Keep in mind our kit is not only less money than others you may find but the screws are stainless steel. Hole size for these rubber inserts is 3/8". Keep in mind the upper lip stands a...

Left side Thermactor smog tube with the jog and bracket around the coil. Bare tube, installation hardware is not included. Not always available, hard to keep on the shelf, look for our reproduction tube set (right and left) available soon. Must have the correct cylinder heads with the drilled and tapped holes for these tubes. Also called air manifold, this unit is part of the air manifold assembly.

Right side Thermactor smog tube. Installation hardware is included as shown. Not always available, hard to keep on the shelf, we always have the reproduction tube set (right and left) in stock. Must have the correct cylinder heads with the drilled and tapped holes for these tubes.

This tube is embedded into the cylinder head making it rather difficult to remove intact. Note that the nut and ferrule assembly is made of two pieces, with the ferrule being a compression fitting used to secure the smog tubes to a series of ports on the cylinder head. Sold individually, 8 total needed for smog installation. Application is 1967 - 1970 390, 427. 428CJ engines. In 1975 Ford started making these out of stainless steel. Tube dimensions 5/16" O.D. x 1.960" long. C6AZ-9A484-C

This one year only, 1969 S code 390-4V or 390IP (Improved performance). Same jog as the 428CJ snorkel. It is technically a 428CJ snorkel with the addition of an adapter on the heat riser opening reducing it down for use with a 2 inch I.D. paper "S" tube. Ford part number C9OZ-9A626-C.

Application would only be for 1969 Boss 302 Eliminators and Boss2 Mustangs. Ford part number C9ZZ-9A626-C

This reproduction cigar / cigarette lighter socket is a good fit and is easy to install. This lighter socket also comes with the retainer. Replaces Ford part # C6ZZ-15055-B.

Used electrical wiring harness that plugs into the main under dash loom. Two wire harness with light socket and shroud for all 1969-70 Mercury Cougar. This can be made to work on a Mustang. Ford number C9WB-14412-A printed on the wire harness.Fits 69 CougarFits 70 Cougar

This new version sequential box works with either standard or plasma LED bulbs NOTE: Although your existing emergency flasher might work just fine with the new sequential unit, it is highly recommended that you also use the same updated electronic sequential flasher in its place to guarantee proper operation. This is a direct fit replacement, just pop open your black plastic box located in the driver side trunk drop off and plug it in. Your January 1970 and newer Cougar will have...

Application small block 289/302/B302 all years 1967 - 1969 with factory Thermactor smog. Spacer for mounting cast iron air pump mounting bracket. Sized .75" O.D. x .73" long. *Note - On Cougars with factory air conditioning 1 spacer is used. On Cougars without air conditioning 2 spacers are used together.

Reproduction 428 Cobra Jet Exhaust Manifold Spacer 1968 - 1970 Mercury Cougar, Ford Mustang, Shelby and Torino Repro

Used angled chrome spacer for any 1969 Mercury Cougar or Ford Mustang. Good used part with very good chrome plating, usually one of the small locating tabs will be broken off of the back. Still a great value compared to the reproduction, and installs fine without the one tab on the back. Replaces Ford part number C9ZZ-11574-A.

C7SZ-3D600-A  Power steering pump adjusting spacer for use without air conditioning. For most 1967 - 1969 Mercury Cougar or Ford Mustang with 289, 302, 390, 428CJ engines, excludes 1969 351W and 1969 Boss 302 engines. Spacer dimensions: 7/16" I.D. x 1" O.D. and 1/2" thick. Same thickness as the pedestal bracket for air conditioning.

Ford small block engines and with a 3 or 4 speed manual transmission. Fits only the larger 164 tooth flywheel.

Original space saver wheel and tire from a 1968-69 Mercury Cougar or Ford Mustang with the elusive 7.35-14 size. These were optional in 1968-69 and pictures show a 1969 date. Never inflated condition. One RARE unit! Just looking for a space saver spare? We have much lower priced space savers with different sized / marked tires, and some with dual valve stems from the 1970's. Please inquire.*NOTE* Does not include inflator bottle and valve caps are usually missing. ...

Reproduction 6 1/4" Spare Tire Mounting Bolt 1968, 1969, 1970, 1971, 1972 and 1973 Mercury Cougar and Ford Mustang

This 5 spoke shield was used to protect the spare MagStar wheel from damage inside the trunk. We currently have one in black and one in gray, both are in mint condition. These were obtained from the Tom Sensabaugh estate, and are very hard to come by.

NOS spare tire lock for the 68 - 73 Cougar Mustang and Torino. Spare tire locks were first offered as an option in 1973, but will fit on any year from 1968 to 1973. The ford master catalog shows that all years from 68 - 73 whether it be Cougar, Mustang or Torino all had the correct size stud for this lock to fit. Fits spare tire hold down J bolts with 1/2-13 course threads, common on Fords 1968-73.  Ford part number D3FZ-1386-A. J bolt not included. ...

Used spare tire lock for the 68 - 73 Cougar Mustang and Torino. Spare tire locks were first offered as an option in 1973, but will fit on any year from 1968 to 1973. The ford master catalog shows that all years from 68 - 73 whether it be Cougar, Mustang or Torino all had the correct size stud for this lock to fit. Fits spare tire hold down J bolts with 1/2-13 course threads, common on Fords 1968-73. Ford part number D3FZ-1386-A. J bolt not included. This icon means that we're looking...

Pertronix brand 7mm spark plug wires. These are performance oriented wires compared to the concours spark plug wires. For any 1967-73 Mercury Cougar and Ford with 351 - 390- 428 - 429 engines. Black wires and boots, quality spark plug wires taylor made for 351 engines and the big block Ford engines. Recommended by Pertronix for use with the Flame Thrower coils.

Want a little more from your hidden speaker system? This is it! The UNDERCOVERII was developed with an 8" woofer and 2 Piezo tweeters in each box. This system can be mounted in many of the same locations as the regular UNDERCOVER. With the 8" woofer in UNDERCOVER II, you get a much fuller, deeper, and richer sound. These fit well under the front seats of 1967-1973 Mustangs and Cougars and have a 200 watt capacity. Measurements are 11"W x 12.5"D x 3"H, sold as a pair. ...

New internal speedometer gear fits 4 speed toploader transmissions. The largest number of 4 speed toploaders came stock with this gear. Replaces Ford Part #: C4DZ-17285-A.

This clips affixes the plastic speedometer gear to the cable. Some have found that this OEM original clip fits a little better than the reproduction we offer. *Trivia* Did you know the first Cougar cast for production in 1968 was this "Custom Cougar"? This fine example was offered up on ebay summer 2008 for a mere $6500.

This is a good used speedometer cable from a 1969 - 1970 Mercury Cougar with a FMX transmission. The cable housing has no burns and the fragile plastic squeeze clip that fastens it to the back of the speedometer is not broken. Keep in mind that some 1970 models use a two part cable. This cable will work in place of the two part cable seen on some 1970 cars. This cable measures 58 1/2" at its very most outer ends.

According to the Master Parts Catalog (MPC), any Cougar with a 3.91 or 4.11 rear end and a 4 speed manual would have been equipped with this reducer. Boss 302 and 428 Cobra Jet engines were the only cars that could be ordered with those rear end ratios. Check with the Mustang 428 Cobra Jet Registry for actual usage, Not always factory installed in 1968-69. Check it out, they have a lot of content on that site. https://www.428cobrajet.org/id... This is a part that we will probably never...

According to the Master Parts Catalog (MPC), Early (before Jan 31, 1969) Cougar with a 3.91 or 4.30 rear end and a 4 speed manual would have been equipped with this reducer. Boss 302 and 428 Cobra Jet engines were the only cars that could be ordered with those rear end ratios. Check with the Mustang 428 Cobra Jet Registry for actual usage, Not always factory installed in 1968-69. Check it out, they have a lot of content on that site. Also found on 1970 4 speed Mercury Cougar and Ford...

The only Cougar that we know came factory equipped with this part is the Cobra Jet. According to the Master Parts Catalog (MPC), any Cougar with a 3.91 or 4.11 rear end and a C-6 would have been equipped with this reducer. Replaces Ford Part #: C8ZZ-17294-A.

The only Cougar that we know came factory equipped with this part is the Cobra Jet. According to the Master Parts Catalog (MPC), any Cougar with a 3.91 or 4.11 rear end and a C-6 would have been equipped with this reducer. This is a part that we will probably never have on hand, but would love to document. If you have one of these adapters, we would be interested in being able to put detailed pictures of it on this listing. Please let us know. We hope to have a reproduction of this adapter...

Spindle nut kit for the 67 - 69 Cougar or Mustang. This 3/4-16 threaded nut fits most of the 1967-69 brake spindles. The exception would be some of the Boss 302 and some 428CJ equipped cars. Included are nut, cap, washer and cotter pin.

Used clutch pedal return spring with two original nylon bushings. Ford Part #: C8OZ-7534-B.

Used steering wheel tension spring used in the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. One required per car. Keeps tension on the steering wheel shaft so as to keep the steering wheel from contacting the upper column cover. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC...

Fits 1968 (mid year change) through 1976 Cougar and Ford forks - All engines.Includes:1 Spring Clip2 RivetsReplaces Ford Part #: C8AZ-7B516-A.

Used 14x5" stamped steel wheel for your Mercury Cougar or Ford Mustang. We save some of the better stock wheels and some have probably ridden in trunks most of their lives. These were offered in 1967, we believe that a 5-1/2 inch wheel was used starting in 1968-69. Have a bent or damaged wheel? Don't have a spare? Shipped bare. Various conditions and subject to availability. Used 'as is', wheel as found in the wilds of our wrecking yard.*Note - these wheels will not work with disc brakes...

Used 14x6" stock stamped steel wheel for the Mercury Cougar or Ford Mustang. We save some of the better stock wheels you will ever find due to our mild climate and some have probably ridden in trunks most of their lives. These were offered from 1968 through 1970. Produced by Motor Wheels, early ones had riveted centers, changed to welded centers in 1969. Specify in the notes section if you have a preference, we seem to have mostly welded ones at the moment. Have a bent or damaged wheel? Don't...

Rebuilt steering gear box with 16:1 ratio and 1-1/8 inch sector shaft. The only difference between SMB-F or SMB-K is the tag and inclusion of the Pitman arm. This is a SMB-F tagged steering box.To be honest, we will seldom have this steering box in stock. We recommend that you purchase the SMB-K steering box, and exchange your SMB-F steering box tag. Return the core steering box with the SMB-K tag back to WCCC. We are building up our inventory of SMB-K steering boxes, so ask for a date...

Used Two Spoke Steering Wheel Pad for the 1969 Mercury Cougar or Ford Mustang. Grade B pads will have minor scuffs and scratches and will need to be repainted. Keep in mind that the pad pictured is just a reference photo and not the actual color you will receive.  Leave a note in the comments section of your order and we will try our best to match your color.

Nice used driver side strut rod that fits all 1968-69 Mercury Cougar and Ford Mustangs. Our good used Western strut rods are the best you will find. No bends, nor damaged threads, not heavily rusted and correct for your Mustang / Cougar and 1968-69 Torino, Cyclone, Ranchero. 1968-69 strut rods are the same as 1970-73 strut rods, but 1968-69 rods have stepped down threads at the end. Ford part number C8OZ-3468-B. Sold as a bare strut rod, we also offer the used hardware for installation...

Our grade "B" rods are just as straight as our grade "A" used rods but the will show pock marks from rust after you clean them. One can fill and sand but it will take time. These are still a much better value than the Chinese rods we sell. This listing is for the driver side only. Compared to what you will find in most regions of the country these would be considered to be very clean in terms of rust damage.*Note - 1970-73 strut rods work equally well.

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Our grade "B" rods are just as straight as our grade "A" used rods but the will show pock marks from rust after you clean them. One can fill and sand but it will take time. These are still a much better value than the Chinese rods we sell. Compared to what you will find in most regions of the country these would be considered to be very clean in terms of rust damage. This listing is for the Passenger side only. *Note - 1970-73 strut rods work equally well. ...

This listing is for a premium quality pair of 1968 - 1969 original strut rods in grade "A" used condition. What sets them apart from our grade "B" rods is they have a smooth finish, no pock marks from rust. This is for the person who is doing a show car and wants the very best, original correct parts that can be found. The reproductions are made in China and work fine but they are different on every detail and do not come with the specialty bolts that attach the rear on the arm to the lower...

Our grade "B" rods are just as straight as our grade "A" used rods but the will show pock marks from rust after you clean them. One can fill and sand but it will take time. These are still a better value than the Chinese rods we sell.*Note - 1970-73 strut rods work equally well.

Stud that the factory line workers used for locating the air conditioning pedestal bracket. Then backed up with a nut. Used on 289 / 302 / 351W / 390 / 428CJ pedestals from 1967 - 1973. We sell this item as reproduction, see related items.*Note - Excludes 351C and 429CJ.

Reproduction 15x6" styled steel wheel for your Mercury Cougar. This unit comes with 4.5" back-space, unless ordered otherwise. Hub caps and lug nuts are sold separately. NOTE! These wheels are intended to be balanced with a lugcentric adapter. They will not balance with a traditional cone spacer on the tire spin balancer. Many tire shops do not deal with classics and do not have the right attachment. If you attempt to balance these wheels without the correct adapter they will resemble a bent...

Used factory 3/4 inch sway bar for the FE 390 engine of 1969. This bar was factory identified with a single 'Yellow' and a single 'Blue' paint stripe. This bar is not to be confused with the Competition Handling Package sway bar which was optional on any 1969 Cougar. This factory used front sway bar does not include any mounting brackets or end link kits. Ford part # C9ZZ-5482-C.