1969 Ford Mustang

Reproduction ram cylinder bracket bushings for the 68 - 70 Cougar or Mustang. If you're having trouble with the bushings on your car ripping or tearing through the hole in your power steering ram cylinder bracket (more so with our reproduction drop down bracket), you can purchase this pair of polyurethane bushings to replace your existing ones. The boot kit we sell also comes with similar bushings, but are a lower quality item, so this set should solve your problem. Sold as a pair. ...

This clip goes on the upper end of your column and keeps your steering shaft from moving around when you pull up on your steering wheel.See item 31804 for new clip.

This passenger side (right hand) reproduction emergency / parking brake cable idler bracket mounts to the right front floor pan. The idler bracket is often discarded when the floor pan is removed for replacement. We also have good used units in stock for those that desire 100% correctness.

This reproduction emergency / parking brake cable equalizer mounts to the end of the parking brake release assembly and captures the emergency brake cable. A very nice reproduction!Replaces Ford part # C6OZ-2A602-A.

Very rare find in the original service replacement boxes dated 10-07-75. Sold as a pair.Ford part # C8WY-65502B20-A.Click on images to enlarge. ...

1969 351-2V Autolite 2100 carburetor, automatic FMX transmission - All 50 states. C9ZF-B stamped on the carburetor base, 1.23" venturi size and 356 cfm. Core, rebuildable carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine.

1969 390-4V Autolite 4300 carburetor, automatic C6 transmission - All 50 states. C9ZF-F stamped on the carburetor base, 1.25" venturi size and 600 cfm. Core, rebuildable carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top.

1969 351-4V Autolite 4300 carburetor, 3 or 4 speed manual transmission - All 50 states. C9ZF-C stamped on the carburetor base, 1.00" venturi size and 470 cfm. Core, rebuildable carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine.

1969 351-4V Autolite 4300 carburetor, automatic FMX transmission - All 50 states. C9ZF-D stamped on the carburetor base, 1.00" venturi size and 470 cfm. Core, rebuildable carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine.

1969 428CJ Holley Carburetor - Core 428CJ service replacement carburetor, automatic C6 transmission - all 50 states. C9AF-9510-U stamped on the carburetor air horn. Holley list #4609, 735 cfm. Core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. *Includes Super Cobra Jet.

1969 428CJ-4V Holley 4150 carburetor, 4 speed manual transmission - all 50 states. C9AF-9510-M stamped on the carburetor air horn. Holley list #4279, 735 cfm. Core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. *Includes Super Cobra Jet.

1969 428CJ-4V Holley 4150 carburetor, automatic C6 transmission - all 50 states. C9AF-9510-N stamped on the carburetor air horn. Holley list #4280, 735 cfm. Core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. *Includes Super Cobra Jet.

1969 302-4V Boss Eliminator Holley 4150 carburetor, 4 speed manual transmission - all 50 states. C9ZF-9510-J stamped on the carburetor air horn with a 903 date code. Holley list #4511, 780 cfm. Core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top.

CARBURETOR SPACER PLATE, 0.28" thick, has correct tab marked "FRONT". Replaces Ford Part Number C8AZ-9A589-G

Original Boss 302 carburetor spacer plate, bake-o-lite with metal tube angled to the side. See the link on the Boss 302 website here.Replaces Ford part number C9ZZ-9A589-C.

New carburetor spacer gasket, goes between the intake manifold and spacer plate. 1969 S code 390-4V or 390IP. Upper gasket, spacer plate to carburetor here.

Grade A used A/C center vent for any 1969-70 Ford Mustang. This will have almost perfect chrome plating, minor blemishes only, no pitting. Fits all models of 1969 and 1970 Mustang. Limited to stock on hand. Does not come with attaching clips, see 'related' tab. Rear dimensions: 6 x 2-1/4 inches. Replaces Ford casting number C9ZZ-19863-A and C9ZA-19C683-A.

Grade B used A/C center vent for any 1969-70 Ford Mustang. This will some limited chrome pitting in the plating. Fits all models of 1969 and 1970 Mustang. Limited to stock on hand. Does not come with attaching clips, see 'related' tab. Rear dimensions: 6 x 2-1/4 inches. Replaces Ford casting number C9ZZ-19863-A and C9ZA-19C683-A.

Correct reproduction available only from WCCC. Notice our consoles feature the correct Burl grain xr7 applique and correct for xr7 3 hump lid. Only available in black, we suggest SEM flexible coating if you need to color them to match your interior. We find that custom mixing the paint will get you better results than their off the shelf selections. Inquire with your local Automotive paint supply house.

New old stock check valve for Bendix brake boosters. This is a white plastic check valve. Ford part number D0AZ-2365-A.Check the related items, for a reproduction rubber grommet.

Screws onto the cylinder head smog tubes. Sold individually, two needed per application. Ford part number C8AZ-9A487-A.

Clamp for supporting and connecting the hard line from the dryer and the suction hose from the condenser.. Two piece clamp with screw. No actual Ford part number listed in the MPC or assembly manuals, the basic part number would be 19B632 though. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon...

These are used hose clamps that have a tab and fold over on them selves. These were dipped in a rubber like substance to prevent chaffing. The ones that we have available do have some cracking or damage to this coating. It should be easy to 'dip' them again with the product that is available in most hardware stores. We normally see 2 of these clamps, or straps bundling the hoses on most cars. These clamps should fit a variety of different Ford and Mercury products, not just Mustang and Cougar....

Stamped steel construction with black vinyl coating like the original to prevent corrosion. Please note that vinyl coating will almost always crack along edges shortly after installation, just like the originals did... This is the same exact hold down you will see listed elsewhere its just that we feel you should know what you are getting up front so you will not be surprised. Replaces Ford part #: C5AZ-10718-A.

Sold individually. Replaces Ford Part # 388052-S Helpful tip: Door panel clips install sliding toward the rear of the vehicle.

Delicate clip that attaches to a nail-head stud attached to the firewall. Very functional and visible, rather hard to find in unbroken condition.

Used plastic clip for the Mercury Cougar or Ford Mustang.

Reproduction of the plastic square hood insulation clips. 11 used on most vehicles. Sold individually.

Used Under-dash Wiring Harness Plastic Cover / Clip for the 1969 and 1970 Mercury Cougar or Ford Mustang

SUPPLIER IS OUT OF STOCK UNTIL MAY 2024 Used in conjunction with Ford fan part # C9ZZ-8600-C that is stamped C9ZE-E. Features a parkerized shaft with an integral mounting flange. The aluminum portions are finished with silver cadmium and are mated together with filister head, Phillips machine screws (8) and an additional crimping operation was used to assemble the front and rear housings. The radial curved spring was originally finished in gold cadmium. This assembly stands 2 5/8" tall when...

C9ZZ-7528-A Equalizer bar or "Z" bar for 351 cubic inch Windsor engines and Boss 302 Eliminators with manual transmissions. Both 3 and 4 speed manual transmissions. This is a used part and it will most likely show some wear form previous use.

D0ZZ-7528-C Equalizer bar or "Z" bar for FE big block engines with a manual transmission. Both 3 and 4 speed manual transmissions. This is a used part and it will most likely show some wear form previous use.

C9ZZ-7519-B Good used pedal but these pedals will no doubt show some wear around the clutch rod holes. Three and four speed pedals are all the same. Mustang is the same too.

Made of heavy gauge steel with a satin black painted finish. Replaces Ford Part #: C9ZZ-7535-A.

D1TZ-7600-A New Old Stock service replacement clutch pilot bushing for all 1965-71 390/428/429 engines with manual transmissions. Will fit 1967-71 Mercury Cougar and Ford Mustang with 390-4V, 428CJ, 428SCJ, and 429CJ engines with 4 speed manual transmissions. Fits Fairlane, Cyclone, Torino, Ranchero also.

New old stock stainless clutch pedal pad trim. About 1/8 inches wider that the reproduction version. Replaces Ford Part #: C9ZZ-7B544-A.

NOS plastic brackets that screw to your roof and then slide a vinyl colored piece over. Sold individually, two are required per car. Ford part # C8AZ-6229232-A.

NOS white colored coat hooks pair. Reproductions only come in black, these are new in the package. White color started in 1970, off white and parchement 1968-69. Fits 1968-73 Mercury Cougar and Ford everything including that Mustang. Ford Part #: D0AZ-6229024-K.

Powerful oil filled coil that generates 40,000 volts, designed to work with the either of our Pertronix Ignitors. Sold in black or chrome. *Note - This coil is not necessarily needed with the Pertronix Ignitors, the stock Ford coil works fine for most applications.

Reproduction coil mounting bracket. The manufacturer claims it fits all cars 1967-73. We happen to know that there are no less than 4 different versions of factory Ford coil brackets used on 1967-73 Mercury Cougar and Ford Mustangs and literally all other Ford cars and trucks. Some have the coil on top of the intake manifold, while some years and engines have the coil mounted to the front of one of the cylinder heads. To our knowledge this is the only reproduction style on the...

New coil spring compressing tool to compress the coil springs of the 1967-73 Mercury Cougar or 1965-73 Ford Mustang. This tool now comes with a bearing to make the job much easier. This spring compressor is a must for safely removing front coil springs. We also offer a 60 Day Loaner if you only need the tool for a short period of time. *NOTE* Not recommended for heavy duty coil springs like found on pickup trucks and full sized cars. ...

Made from polyurethane, a bit more rigid and stiffer than our rubber insulators. Sold individually. Two required per vehicle. These are the coil spring insulators available from most Mustang/Cougar suppliers. Replaces Ford Part #: C4DZ-5415-A.

This is an original NOS hot idle compensator for Mercury Cougar or Ford Mustang models with V-8 engine and factory A/C. It is installed in the middle of the hose that connects the PCV valve to the rear of the carburetor spacer. It opens when it reaches a certain temperature which makes the engine run faster when at idle and the A/C is on thereby making the engine run more efficiently. This is an original Ford part that came on air conditioned models from the factory. It was manufactured by...

This listing is for a 3 bolt type upper ball joint, NOS, original Ford Service replacement upper control arm assembly. We have a very hard time keeping these in stock but we keep the listing up as it is good for comparison sake when considering the differences between reproduction and OEM. Keep in mind, service replacement parts often differ slightly from what actually came on the car. Over the years tooling is often replaced or modified and suppliers of things like fasteners often change....

This windshield wiper delay governor mounts to the driver side firewall. To find where this mounts on the firewall

Original used three piece tack strips for the 1969 - 1970 Cougar convertible. Over-sized, must be shipped via UPS.

This pair of reproduction convertible top hooks are beautifully chrome plated and features correct thread size. Looks close to original. These hooks are actually for 71 - 73 Cougars and Mustangs, but will work just fine on the 69 - 70.

C9ZB-7653139-A is the part number for the drivers side, C9ZB-7653138-A for the passenger side. These will often break when one hydraulic lift cylinder malfunctions and the other is still working. This scenario will put the top frame in a bind causing one of these cast parts to break. We carefully inspect these before shipment for cracks, worn areas or corrosion.