1969 Ford Mustang

Reproduction heater cable for Mercury Cougars and Ford Mustangs equipped with factory A/C. Replaces part # C9ZZ-185188-A.

C9ZZ-18A651-A Complete heater control assembly includes bezel or face plate, bracket control mounting plate, electrical and vacuum switches. Functional, driver quality, heater control assembly. Expect some degree of wear and tear on the plastic knobs and the lever borders. Knobs and light socket wiring harness not included. *RESTORATION TIP* If you like to restore your own parts, you can purchase plastic polish for the lenses that will take out the haze with a bit of elbow grease. A...

Constructed from corrosion resistant copper and brass. Quality replacement part for a job you do not have to do again anytime soon. Replaces Ford Part #: C9ZZ-18476-B. Check out our videos below on how to replace a heater core! We now have separate videos for the first generation ('67-'68) and second generation ('69-'70). ...

Our heater cores are the finest available anywhere for any price and they are constructed from corrosion resistant copper and brass. A great buy for anyone who is sick of smelling anti-freeze and needing to make repairs to this vital part. Replaces Ford Part #: C9ZZ-18476-A. Check out our video below on how to replace a heater core! We used a '69 Cougar with A/C, but many of the same concepts apply to other years. ...

Concours correct red striped heater hose for 1969 Mercury Cougars and Ford Mustangs with factory or integral air conditioning. Durable red striping with "Autolite" spelled out and dated H8H02A. These hoses have a correctly molded 90 degree elbow on one end that fits on the water valve side. Some length trimming may be required for a tight looking fit.

Concours correct red striped heater hose for all 1969 Mercury Cougars and Ford Mustangs WITHOUT air conditioning. Correct for use with all V-8 engines. Durable red striping with "Autolite" spelled out and dated H8H02A. Some length trimming may be required for a tight looking fit.

New bolt for attaching the window guide to the door window bracket on any 1969-70 Mercury Cougar or Ford Mustang with glued in side glass. Two per guide (4 guides per car). 8 total, four on the passenger side, four on the driver side. 1/4"-20 x 5/8" Large Flange Spin Lock Bolt.

Bolt for the under side convertible plate on any 1969-73 Mercury Cougar or Ford Mustang. 6 total bolts needed for attaching reinforcement plate to undercarriage. Sold individually. These are a close match to the original bolts, which are 3/8-16 x 1-1/2". Ford tightening specs. are 25-38 lbs. ft. torque.Replaces Ford number 57048-S2.

Machine hex bolt for installing the heater cables to the climate controls on any 1969-73 Mercury Cougar or Ford Mustang. 8-32 threaded hex machine screw like the originals. Attaches cables for heater only or factory A/C cables.

Nut for attaching the power steering pump bracket onto the pivot stud coming out of the cylinder head. All 1967-69 Mercury Cougar and Ford Mustang engines additionally used on 1970 428CJ engines.

Reproduction hex screw for exhaust pipe clamps for the 1967 - 1973 Mercury Cougar and Ford Mustang. 5/16 x 1-1/2 screw. Fits original and new clamps.

This H5006 bulb is the closest Halogen Reproduction of the original FoMoCo headlights that we carry. This bulb has the number 2 at twelve o'clock (to indicate its position in your grille) just like the original, and the FoMoCo logo is actually formed into the glass rather that being etched onto it, as is on some other repros. This high / lo beam is definitely going to be brighter than your original dim bulbs. Also note: Other than Cougars, only the 1969 Mustang used these bulbs.Don't forget...

This H5001 bulb is the closest Halogen Reproduction of the original FoMoCo headlight that we carry. This bulb has the number 1 at twelve o'clock (to indicate its position in the grill) just like the original, and the FoMoCo logo is actually formed into the glass rather that being etched onto it, as is on some other repros. This high beam is definitely going to be brighter than your original dim bulbs. Note: Other than Cougars, only 1969 Mustangs used these bulbs. Don't forget that you need to...

Used hinge for any 1969-70 Mercury Cougar or Ford Mustang. Comes as shown, we select the best hinges to inventory, most will have the original dash color paint.Replaces Ford part number C9ZZ-6506050-A.

Fits Standard and XR7 Sold as a Set as Pictured.

Set comes with economy grade pliers and 150 hog rings, enough for one bucket seat, probably two.

This kit contains 500 hog rings, more than enough for two bucket seats and one bench seat.

Reproduction replacement hold down clamp for the distributor on any 67 - 73 Cougar or Mustang. Sold individually, 2 needed per car.

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Improved reproduction left hand hood hinge for the Mercury Cougar and Ford Mustang. Very heavy duty compared to the originals, thicker metal and slightly wider hinge bars. These hinges weigh 4.35 lbs, originals weigh 3.2 lbs. Hood hinge rivets have the 'plus' markings like seen on the 1969-70 hinges. Save your hinge springs, these do not come with the new springs. It is easier to fit and adjust these hinges without the spring installed on them. We use an old section of seat belt for removing...

This is for you folks out there who want the correct part number on your hinge. Good used OEM original hood hinges that are available individually or as a set. We now offer a PREMIUM quality reproduction that is superior to any other reproduction. We carefully inspect these hinges before sending them as used hinges are prone to wear in more than one area. Here is a helpful youtube video that shows you how to adjust your hood. Shipped with the spring. These will work on all 1967-70 as well. But...

Improved reproduction right hand hood hinge for the Mercury Cougar and Ford Mustang. Very heavy duty compared to the originals, thicker metal and slightly wider hinge bars. These hinges weigh 4.35 lbs, originals weigh 3.2 lbs. Hood hinge rivets have the 'plus' markings like seen on the 1969-70 hinges. Save your hinge springs, these do not come with the new springs. It is easier to fit an adjust these hinges without the springs installed on them. We use an old section of seat belt for removing...

This is for you folks out there who want the correct part number on your hinge. Good used OEM original hood hinges that are available individually or as a set. We now offer a PREMIUM quality reproduction that is superior to any other reproduction. We carefully inspect these hinges before sending them as used hinges are prone to wear in more than one area. You can find the hood hinge apron nuts here. Here is a helpful youtube video that shows you how to adjust your hood. Shipped with...

This reproduction hood hinge nut and bolt kit fits both the Standard and XR7 and is sold as a kit as pictured. These connect the hinge to the hood itself, and connect the hinge to the fender apron.

Improved reproduction right and left hand hood hinges for the Mercury Cougar and Ford Mustang. Much heavier duty compared to the originals, thicker metal and slightly wider hinge bars. These hinges weigh 4.35 lbs, originals weigh 3.2 lbs. Hood hinge rivets have the 'plus' markings like seen on the 1969-70 hinges. Save your hinge springs, these do not come with the new springs. it will be easier to fit and adjust these hinges prior to installing the springs on them. We use an old section of...

A modern touch to this classic muscle car look. This kit is the same Scott Drake "Shelby Style" Billet hood pin kit offered by many other vendors.Kit includes 2 Hood Pins, 2 dowel pins, 4 Nuts to hold the dowel pins on, machined billet aluminum top plates for the top of the hood, 8 screws to hold the hood plates on and 2 tie down cables. The difference between this version and the deluxe version, is that these are Machined billet aluminum top plates and the deluxe is stainless steel. Common...

This kit is the same Scott Drake "Shelby Style" DELUXE hood pin kit offered by many other vendors.Kit includes 2 Hood Pins, 2 dowel pins, 4 Nuts to hold the dowel pins on, plates for the top of the hood, 8 screws to hold the hood plates on and 2 tie down cables. The difference between the standard version and this deluxe version, is that the standard is chrome plated and the deluxe is stainless steel. Common consensus is that the holes for the pins were hand drilled at the factory, so the...

This kit is the same Scott Drake "Shelby Style" hood pin kit offered by many other vendors.Kit includes 2 Hood Pins, 2 dowel pins, 4 Nuts to hold the dowel pins on, plates for the top of the hood, 8 screws to hold the hood plates on and 2 tie down cables. The difference between this version and the deluxe version, is that these are chrome plated and the deluxe is stainless steel. Common consensus is that the holes for the pins were hand drilled at the factory, so the exact location varied from...

* - This scoop can be used for 1969 - 1970 Cougar Eliminators and many other Ford models that had similar scoops.  This is not the correct scoop for the 1969 - 1970 Cougar Eliminators, but it is the closest scoop currently reproduced to the 1969 - 1970 Cougar Eliminator scoop. BOSS 302, 351w, 351c, 390 and 428 Eliminator Cougars all used the same scoop whether they were equipped with Ram Air or not. The original scoop measures 21 5/8" at the widest point on the front, 25" at the...

Welded in hooked retainer for the rear seat back installation on any 1967-73 Mercury Cougar or Ford Mustang coupe or hard top body style. This bracket welds to the edge of the package tray. Two hooks per car, sold individually. We cut out a individual sections as shown. Make good measurements prior to removal of your old brackets. You will need to drill out the spot welds prior to installation. For sure that basic Ford part number is 62118.

This item has been discontinued until further notice.Basically correct looking except for screws in place of the rivets. The High or Low tone is indicated in raised letters located on the perimeter of the horn. Replaces Ford Part #: C9ZZ-13832 / C9ZZ-13833 or C9ZF-13801-B / C9ZF-13802-C.

This item has been discontinued until further notice.The High tone is indicated in raised letters located on the perimeter of the horn. We do offer the correct used Cougar horns.Replaces Ford Part # C9ZZ-13832 or C9ZF-13801-B.

This item has been discontinued until further notice.The Low tone is indicated in raised letters located on the perimeter of the horn. We do offer the correct used Cougar horns.Replaces Ford Part # C9ZZ-13833 or C9ZF-13802-C.

Attaches behind the drivers side horn on all 1969-70 Mercury Cougar and Ford Mustangs with air conditioning. We believe that this part was installed to maintain clearance with the A/C condenser. Ford part number C9ZF-13925-A as seen in the 1969 Electrical Assembly Manual.

Used on two spoke steering wheels. Replaces Ford Part # C0DZ-13807-A. Although it does not "look" right it will function correctly. Those in the know will purchase our good used spring.

Wire extension for horn relocation, when the drag pak or drag pack option was ordered typically with 3.91 or 4.30 rear axle ratio. Fits all 1969-70 Mercury Cougar or Ford Mustang with factory oil coolers. Should also fit Torino and Cyclone. Reproduction of Ford part number C9DB-13A840-A.

Decent used horn ring but unlike our grade "A" used horn ring this one will have very minor pitting but no open blisters in finish. Good value for your driver quality 68-69 Ford / Mercury with two spoke steering wheel.

Reproduction Two Spoke Steering Wheel Horn Ring for the 1968 and 1969 Mercury Cougar. This is a very good reproduction piece. The original horn contact pieces fit nicely. This casting, while different than the 1968 version with the empty cavities is actually stronger. *NOTE* Save your old horn ring, you will need to transfer the rubber spacer and the horn contacts to this reproduction part.*CUSTOMER REVIEW* Called WCCC the other day after calling around to a lot of garages and auto parts...

Tested and working used pair of Hi and Lo tone horns. 1969-70 Mercury Cougar and Ford Mustang used part number C9ZF-13802-C and C9ZF-13801-B. Every horn is bench tested and inspected for cosmetic defects, if they do not function properly, and pass a visual inspection, they get recycled. The used horns at WCCC can be used as-is or you can clean and detail them for your show car.

Reproduction brake booster hose for Mercury Cougar or Ford Mustang. Measures 12" long

Reproduction date coded breather cap hose for the 68 - 70 Cougar or Mustang.Date code: 1/26/70

Reproduction date coded breather cap hose for the 68 - 70 Cougar or Mustang.Date code: 10/25/67

Reproduction date coded breather cap hose for the 68 - 70 Cougar or Mustang.Date code: 10/25/68

Reproduction date coded breather cap hose for the 68 - 70 Cougar or Mustang.Date code: 10/28/69

Reproduction date coded breather cap hose for the 68 - 70 Cougar or Mustang.Date code: 12/5/68

Reproduction date coded breather cap hose for the 68 - 70 Cougar or Mustang.Date code: 2/25/69

Reproduction date coded breather cap hose for the 68 - 70 Cougar or Mustang.Date code: 2/29/68

Reproduction date coded breather cap hose for the 68 - 70 Cougar or Mustang.Date code: 6/25/68