Body

Used passenger side (right hand) vinyl top moulding / trim for your Mercury Cougar. Good used part with no heavy scratches or broken studs. Speed nut fasteners are sold separately. This trim requires a total of 4 speed nuts.Ford part # C7WY-65423A18-A.Fits: 1967 Mercury Cougar1968 Mercury Cougar

This is a set of four rechromed die cast mouldings that attach via speed nuts at the bottom of your vinyl top. These do not pry off! Use your 1/4" drive ratchet with a deep 11/32" socket and small extension. You must remove your rear interior side panels to access the studs for the side mouldings. New speed nuts included, just in case.. If you have extra sets of cores above and beyond the four needed to exchange, we would be willing to give in store credit. Restored moulding will not ship...

This is an OEM original with 3/8"-16 threads. Overall length according to the MPC is 9 inches, with 3-1/4 inches being threaded but we have found almost without fail, the actual length is 8" with 3 1/4" of threads. We also carry the OEM hold down wing nut or spinner nut Mercury Cougar part number B9AZ-1462-A. Additionally, look for the wheel centering plate or disc, part number C5ZZ-1424-A. Item for sale in this section is only the J-bolt.

Steel plate for mounting the door pull or grab handle on 1967-68 Mercury Cougar XR7. Right and left is dependent upon which way the nylon inserts are installed. Comes complete as shown with nylon inserts for attaching the door pulls. The screws with 1/2 inch flat head for mounting this plate to the doors are also a available (three required).

Used mounting bracket for the sunroof motor on the 67 - 70 Mercury Cougar. This bracket is only used with the 67 - 70 power sunroof motor.

4" mounting Plate for Standard Spare Tire. Replaces Ford Part #: C5ZZ-1424-A.

Reproduction side view mirror screw. These screws are sold individually. Do you have riv-nut questions? Here are riv-nut answers!

These spacers are required to properly mount the trunk lock housing to the trunk. Two required per car, sold individually. Ford part number C7WY-6543565-A. Check out this video

These spacers are required to properly mount the trunk lock housing to the trunk lid.  Sold as a pair. Replaces Ford part number C7WY-6543565-A. Follow this link to find the lock housing nuts. Check out this video

This is our reproduction quarter panel extension nut for the Mercury Cougar or Ford Mustang. Sold individually.Replaces Ford part # 373556-S.

New O-ring gasket for the 1967-68 Mercury Cougar flip trunk lock cylinder. Lock cylinder must be removed from the trunk lock housing to install. Original O-rings are normally cracked and broken when we disassemble them. 

Full driver (left hand) side front frame rail measures 52" long and the outer rail has weld nuts installed for proper installation.

This listing is for the outer wheel house on a 1967 or 1968. Often when you replace the skin you will find multiple soft spots in the outer wheel house, especially down low. If you do not want to pay the oversized shipping on these large items we do sell patch panels.We also sell these as a complete set of four, which will save you money on shipping as we unbox them and nest all four together and fit them in one box. ...

This listing is for the outer wheel house on a 1967 or 1968. Often when you replace the skin you will find multiple soft spots in the outer wheel house, especially down low. If you do not want to pay the oversized shipping on these large items we do sell patch panels.We also sell these as a complete set of four, which will save you money on shipping as we unbox them and nest all four together and fit them in one box. ...

This listing is for the outer wheel house upper patch for the driver side of your 67-68. 

This listing is for the outer upper wheel house patch for the passenger side of your 67-68.  

This listing is for outer wheel house lower patches, front and rear for the driver side of your 67-68. There is no cost savings on the purchase price, but often people only need the lower section and shipping these (especially overseas) can be cost prohibitive. Since we cut these in house you can request where we cut if you would like a custom cut different than what is pictured here.

This listing is for outer wheel house lower patches, front and rear for the passenger side of your 67-68. There is no cost savings on the purchase price, but often people only need the lower section and shipping these (especially overseas) can be cost prohibitive. Since we cut these in house you can request where we cut if you would like a custom cut different than what is pictured here.

New product that is in stock and ready to ship! Unlike 1968 the 1967 xr7 console indicator light bar had no woodgrain applique. This will work fine on your 68 and some prefer the 1967 look over the 1968 version. We have a few of these with a 1968 Burl Wood Overlay applied to them. If you would like one of these, mention it in the order notes and if we have any remaining will send you one of these. These two pictures give you an idea what the lights will look like when illuminated. When not lit...

Reproduction mastic sound deadener for the package tray on your 1967 Mercury Cougar. 

Great for those wishing to shed a few pounds from their early Cougar as this insulation weighs less than one pound and the original weighed almost four pounds. If you want to keep your Cougar original then you will want to check out our used package tray sound deadener / insulation / jute. *NOTE* This is actually patterned for a 1968 Cougar, but will work in a 1967.

These fasteners were used to keep your package tray in place. In 1967 - 1968 two T shaped fasteners were held in place with a spring clip. Sold individually. Ford part number C4AB-6246698-A

Reproduction cover board for the rear package tray found on the 1967 Mercury Cougar behind the rear seat, visible through the rear window. The 1967 tray is deeper as it installs over the tops of the rear side panels. In 1968 they installed under the rear vinyl covered panels. The difference between the WCCC panels and the others on the market is that we run them through a drum sander so as to give the textured side a more muted look and feel than unsanded masonite board. The other brands do...

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. This ORR LAC chassis black paint will give the appearance of an expensive, baked on finish. Also usable on other tools, equipment, vehicle frames, shop racks, trailers and more. ORR-LAC 923 Semi Gloss black.

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT.This VHT roll bar and chassis paint will give the appearance of an expensive, baked on finish. Heat resistant to 250 degrees, this epoxy coating also resists chemicals, rust, corrosion and salt. No primer is needed. Also usable on other tools, equipment, vehicle frames, shop racks, trailers and more. ...

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. SEM brand COLOR COAT paint is formulated to match, restore or change color on most vinyl surfaces, flexible and rigid plastics, carpet and velour. COLOR COAT is fade resistant, flexible and is a semi-permanent coating. We do not recommend this product for driver side arm rests, door pull straps, shift...

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. This is a GOOD match for 1967-68 Cougar parchement / off-white interiors. SEM brand COLOR COAT is formulated to match, restore or change color on most vinyl surfaces, flexible and rigid plastics, carpet and velour. COLOR COAT is fade resistant, flexible and is a semi-permanent coating. We do not...

This charcoal black aerosol paint is a very close match to the original finish used on 1967-68 Cougar XR-7 lower dash structures and steering columns. We've tried it ourselves and have been satisfied with the results. Our only critique is that it's a bit slower to dry than other paints we're used to. The AccuMatch(TM) Interior Paints are the result of years of work and perfectly match the original color shades. Each color has been expertly color-matched. Paints feature extra-high pigment...

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. This SEM plastic and leather paint prep is for cleaning surfaces before applying the SEM flexible vinyl paint. Removes mold, grease, oil and other contaminates from leather, carpet, velour and vinyl.

New pair of white and yellow paint sticks for the Mercury or Ford. These units were used by FORD at the assembly plants to mark fender aprons

Professional grade paintless dent removal kit. This kit is designed to work with smaller blemishes such as dents from hail, door dings, etc. Complete with universal high strength glue sticks, puller, and a variety of different sized gluing tabs. NOTE: Remove glue with 91% alcoholAlthough we work with 67 - 73 Cougars and Mustangs, this kit is good for a wide variety of different vehicles.

Reproduction anti rattler board - 1/8" panel board that prevents rattling noise. Installs on top of fuel tank on the side where the jack and spare tire mount.Measures 12" X 6"

This listing is for the person who only has rust under the lip at the front and does not want to pay shipping on an entire frame that must ship via truck freight. It will come as shown unless you contact us. The part will be the same price no matter where we cut it, let us know in the comments section where you would like us to cut if you want something other than what is shown. ...

This listing is for the person who only has rust under the corners at the rear and does not want to pay shipping on an entire frame that must ship via truck freight. It will come as shown unless you contact us. We can also cut the section in half if you only need one corner.  The part will be the same price no matter where we cut it, let us know in the comments section where you would like us to cut if you want something other than what is shown. ...

This reproduction cowl vent repair panel for the passenger side (right hand) of the Mercury Cougar or Ford Mustang addresses a common problem with these old Cats and Ponies. Rust in the cowl. Easy to install on the driver side, but takes more effort on the passenger side, especially if you have air conditioning. These panels are also called fresh air cowl vents or inner cowl vent repair panels. Another way to avoid doing expensive cowl repairs is to purchase our cowl cover.*NOTE* ...

Front guide that measures 10 5/8" long held in place by four screws. The driver side has no markings but the passenger side is stamped with an R and the inner 2 screw holes are in a different place than the driver.

Rust free with no prior damage. Cut with a plasma cutter well above the style line from a solid Western fender. Generally we cut these about 14" up but you can have it cut anywhere you wish and the price remains the same, only the shipping increases. Keep in mind that the 67 did NOT have the cutout for the side marker light and the 68 did.

Rust free with no prior damage. Cut with a plasma cutter well above the style line from a solid Western fender. Generally we cut these about 14" up but you can have it cut anywhere you wish and the price remains the same, only the shipping increases. Keep in mind that the 67 does NOT have a cutout for the side marker light like the 68 has.

Rust free with no prior damage. Cut with a plasma cutter well above the style line from a solid Western fender. Generally we cut these about 14" up but you can have it cut anywhere you wish and the price remains the same, only the shipping increases.

Rust free with no prior damage. Cut with a plasma cutter well above the style line from a solid Western fender. Generally we cut these about 14" up but you can have it cut anywhere you wish and the price remains the same, only the shipping increases.

Reproduction patch panel for the wheel lip on the driver side (left hand) quarter panel on the Mercury Cougar. These over the rear wheel patch panels are cut from the reproduction skins we sell. If you need something cut larger please email us with a diagram or picture and we will cut to suit for a reasonable up charge.  These panels are made from 20 gauge (.036-.037) steel, typically cut 23" x 13"

Reproduction patch panel for the wheel lip on the passenger side (right hand) quarter panel on the Mercury Cougar. These over the rear wheel patch panels are cut from the reproduction skins we sell. If you need something cut larger please email us with a diagram or picture and we will cut to suit for a reasonable up charge.  These panels are made from 20 gauge (.036-.037) steel, typically cut 23" x 13" ...

If you are buying our one piece Mustang floor pan or our driver side rear extended floor pan, you will find they line up great until you come to the area where it meets the wheel house. The inner Wheel house is very different Mustang vs. Cougar and this used custom cut will be needed if your existing pan needs replaced all the way to the wheel houses. If you need more material than what is shown contact us with a picture of your needs and we can cut to suit. ...

If you are buying our one piece Mustang floor pan or our passenger side rear extended floor pan, you will find they line up great until you come to the area where it meets the wheel house. The inner Wheel house is very different Mustang vs. Cougar and this used custom cut will be needed if your existing pan needs replaced all the way to the wheel houses. If you need more material than what is shown contact us with a picture of your needs and we can cut to suit. ...

Reproduction rear floor patch panel for the 67 - 70 Cougar. This is the floor pan directly to the inside of the driver side wheel well, and has the holes for the rear seat belt bolts. Cut in house from a complete reproduction trunk pan. NOTE* If you buy both sides left and right we can leave them as one continuous panel at no extra charge just for the asking, please leave a note on your online order in the comments section. ...

Reproduction rear floor patch panel for the 67 - 70 Cougar. This is the floor pan directly to the inside of the passenger side wheel well, and has the holes for the rear seat belt bolts. Cut in house from a complete reproduction trunk pan. NOTE* If you buy both sides left and right we can leave them as one continuous panel at no extra charge just for the asking, please leave a note on your online order in the comments section. ...

Trunk patch panel cut in house from a complete transition panel. This is a patch for the area forward of the fuel tank just before the transition hump. 

Reproduction lower rear window channel patch panel for the Mercury Cougar. It is fairly common for the rear window channel area to develop rust, especially with vinyl topped cars. *NOTE* If you are going t install this part on a Cougar with a vinyl top, you will have to drill holes for the vinyl top moulding / trim.