Body

Good original driver side door latch rod set. Includes rod for inside lock, outside key lock, and outside door release actuating rod. These are good used parts and are a better quality and value compared to the reproductions. Only fits passenger side doors of 1967 Mercury Cougar and Ford Mustang. 1967 door latches are unique, they have a short tab for the inside door lock knob typically. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown...

Made for Mustang but can be tweaked to work on Cougar. We advise you buy our good used rods.

Good original passenger side door latch rod set. Includes rod for inside lock, outside key lock, and outside door release actuating rod. These are good used parts and are a better quality and value compared to the reproductions. Only fits passenger side doors of 1967 Mercury Cougar and Ford Mustang. 1967 door latches are unique, they have a short tab for the inside door lock knob typically. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers...

Convenient matched sets save costly locksmith work. Kits includes a pair of door lock cylinders. Comes with two keys. Includes door cylinder gaskets. If you don't mind have having a different key for the door locks, this product might just work out.Attention potential buyer! This item will likely give you problems and be a general disappointment. Reviews show that the fitment is fair, and you will not be able to have these lock cylinders re-pinned, to use your original Ford key. One...

Check out our door panel inventory video below: *NOTE* Door panels sold bare, meaning without hardware, armrests, map pockets, window cranks, courtesy lights, door pulls, or door handles. ...

These are so nice... The texture is exact, the rubber feel is right, the fit is perfect, the colors are correct "except aqua which is a darker than Cougar, Mustang color". These used to be very hard to find in good used condition, why bother with used when you can get them at this price. Sold as a pair.Replaces Ford Part # C8ZZ-6526656. *Customer Feedback* Don and staff; Just to let you gentlemen know that I have received the 1967 XR7 saddle tan door panels you sent and I am extremely happy...

These are so nice... The texture is exact, the rubber feel is right, the fit is perfect, the colors are correct "except aqua which is a darker than Cougar, Mustang color". These used to be very hard to find in good used condition, why bother with used when you can get them at this price. Sold as a pair Replaces Ford part # C8ZZ-6526656.

New, more accurate woodgrain as of 2019! These decals are cut to fit the 1967 door pull end caps. The 1968 end caps had a smaller woodgrain insert with a black border. We also sell a slightly smaller version of this kit for the 1968 owners. This kit also fits the reproduction end cap kit. Check out this video

Great quality reproduction of the interior door strap (grab handle) end cap hardware. This kit is actually our straight grain end cap set, but we include the burl applique decals for you to change out, simply remove the straight grain decals and insert the burl decals. Great price considering good used sold for about $100 before these were available.  ...

Great quality reproduction of the interior door strap (grab handle) end cap hardware. If you have a 67 the woodgrain decals are the correct size, the 68 uses a little different design with a black border which is not available new. The woodgrain is not correct for either 67 or 68. We would highly recommend getting our burl wood applique, it is still not correct, but is much closer and nicer than the woodgrain this comes with. Great price considering good used sold for about $100 before these...

You may consider buying our grade "B" door over our grade "A" door if you are doing a high end restoration. Here is the reasoning; due to the design of the 67-68 door, silt is trapped in all of the door corners, these tight recesses always have silt collected in them and when you add moisture you get corrosion. Our grade "A" doors do not have noticeable blisters but since there is no paint or sound deadener in the depths of the corners we know there is some amount of corrosion taking place...

You may consider buying our grade "B" door over our grade "A" door if you are doing a high end restoration. Here is the reasoning; due to the design of the 67-68 door, silt is trapped in all of the door corners, these tight recesses always have silt collected in them and when you add moisture you get corrosion. Our grade "A" doors do not have noticeable blisters but since there is no paint or sound deadener in the depths of the corners we know there is some amount of corrosion taking place...

Fits both left or right, sold individually. These have a higher degree of luster than the originals but are made of same material and weigh exactly the same as our NOS examples. Very little difference from our more expensive version which is made using original tooling. Ford Logo sold separate, sold individually, two required per car. Replaces Ford part # C5ZZ-6513208-B or C5ZZ-6513208-D.

Decent, used, driver quality part that will have scratches and dings consistent with a Cougar that has been on the road for decades. Even if we look through our pile and find the best we have it still will show wear, expect it to look just as ugly as the one pictured. Sold individually.

New Supplier Now Available! *Unlike our other sill plates, these are sold as a pair* Ford never made these in stainless but what a great upgrade! The advantage we see with these is that they do not dent or scratch as easy when you release your seat belt. They also can be polished easily (unlike anodized aluminum). These weigh 1.5 pounds each, triple of what the originals weigh. Sold as a pair only. *NOTE* There are two suppliers on these and we now carry only the Dynacorn...

Very nice reproduction, silver zinc finish like original. Correct texture and even an original type date stamped on the head. Comes complete with striker plate, shim, and screws. The only difference between the 67 Cougar and the 68 - 70 is that the 67 came with the 8-66 date stamp, the rest came with the 11-67 date stamp. Note: Some Cougars did not have date stamps from factory. Replaces Ford part # C5AZ-6222008-B.

Very nice reproduction, silver zinc finish like original. Correct texture and even an original type date stamped on the head. Comes complete with striker plate, shim, and screws. The only difference between the 67 Cougar and the 68 - 70 is that the 67 came with the 8-66 date stamp, the rest came with the 11-67 date stamp. Note: Some Cougars did not have date stamps from factory. Replaces Ford part #: C5AZ-6222008-A.

Reproduction polished stainless steel door strikers for your Mercury Cougar or Ford Mustang. This kit includes stainless steel hardware and will make your door jambs pop.Replaces Ford part # C5AZ-6222008-A.

C7WB-13A769-D Same harness works for driver or passenger side, sold individually. Found on 1967 XR7 and Standard Cougars with Safety Convenience Package, console or dash mounted warning lights. C7WB-13A769-D is the tag number originally found on the harness. Wiring harness for door ajar and courtesy light. This is a grade "B" good used harness, expect minor splices, damaged rubber boots or other easily repairable minor damage.

Round hood latch dowel that screws into the hood on all 1967-68 Mercury Cougars. Threads are 1/2-13, dowel assembly includes threaded dowel, jamb nut and washer as shown.Fits many other Ford products, see list below.Replaces Ford part numbers C4ZB-16929 and C5ZZ-16929-A.

Round hood latch dowel that screws into the hood on all 1967-68 Mercury Cougars. Threads are 1/2-13, dowel assembly includes threaded dowel, jamb nut and washer as shown.Fits many other Ford products, see list below.Replaces Ford part numbers C4ZB-16929 and C5ZZ-16929-A.

Premium grade and quality reproduction floor pan plug. These screw right onto the floor pans prior to the carpet underlay and are much better quality than the originals. The original plugs have rough stampings and are made from galvanized steel. These premium plugs have a smooth cutout and are zinc plated. Fits: 1967 Mercury Cougar1968 Mercury Cougar 1969 Mercury Cougar 1970 Mercury Cougar 1971 Mercury Cougar 1972 Mercury Cougar 1973 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang 1969 Ford...

Used custom cut driver side roof section of the drip rail for the 67-68 Cougar. This listing is for anyone who has rust on the rail section of the roof and needs a cut from a good donor car for a patch panel. Generously cut approximately 4 inches deep, from the "A" pillar all the way to the rear portion of the quarter. Ford part number C7WY-6551701-B

Used custom cut passenger side roof section of the drip rail for the 67-68 Cougar. This listing is for anyone who has rust on the rail section of the roof and needs a cut from a good donor car for a patch panel. Generously cut approximately 4 inches deep, from the "A" pillar all the way to the rear portion of the quarter. Ford part number C7WY-6551700-B

This is the gear on the upper side of the gearbox. The cables go over each side of the gear.NOTE: Be sure the gear is in good condition so your cables don't get worn out!

This shim, also referenced to as washers, goes in the clutch portion of the drive gearbox to properly adjust the friction. Three shims (plus a hand crank) were originally supplied with sunroof cars.

This reproduction cowl vent repair panel for the driver side (left hand) of the Mercury Cougar or Ford Mustang addresses a common problem with these old Cats and Ponies. Rust in the cowl. Easy to install on the driver side, but takes more effort on the passenger side, especially if you have air conditioning. These panels are also called fresh air cowl vents or inner cowl vent repair panels. Another way to avoid doing expensive cowl repairs is to purchase our cowl cover.*NOTE*  While...

Front guide that measures 10 5/8" long held in place by four screws. The driver side has no markings but the passenger side is stamped with an R and the inner 2 screw holes are in a different place than the passenger.

Reproduction electric rear deck / trunk lid release. Includes electric lock latch, control knob and wiring needed to install.Detailed instructions included.

This emblem was used on the driver side of the 1971 - 1972 Cougar hood and on the passenger side of the trunk lid in 1967 - 1968. Also used on various other Mercury products like the Comet, Cyclone, and Marquis prior to 1973. This will not fit on the fender extension of the 1967- 1968 Cougar. Fantastic quality part... In our experience, we have found that you would have to obtain several NOS emblems before you found one with chrome as nice as this. The quality on these new emblems is very...

This is the aluminum emblem which mounts on the center of all scuff plates. Features raised script surrounded by "Product Of Ford" like original, adhesive backed and protective coating. Sold individually, two required per car. Replaces Ford part # C8ZZ-6513208-T.  Technically this is the version found on early 1967 cars, the late 67 and 1968 versions had a larger blue oval 'Ford', and did not have the 'Product of' line.

No... Mercury never made an emblem "just" like this one but demand dictated we produce it! This emblem has a 3M adhesive backing and looks and measures just like a 1968 quarter panel script or the front fender script found on a 1971 - 1973. Many people do not like the looks (or price) of the 67 quarter panel emblems so this is a great alternative that does not require you drill holes. The 3M backing is the same found on modern automotive emblems so it will not fall off. Just like our other...

Holds both both the speedo cable and the parking brake cable in place with two self tapping bolts. Bolts not included, picture is for reference only. Part will have rust, but not severe.Replaces Ford part number 381821-S2 per the Chassis Assembly Manual 1967 page 17, 1968 Page 39.

This is the first bracket to secure the emergency brake cable as it exits the firewall. It mounts to the frame rail. It is held on by one bolt which is not included, picture is for reference only. Part will have rust but not severe.

New high temperature enamel for painting your block and underhood parts. So far, the best match has been the VHT brand, SP138 "Dark Ford Blue" paint (sometimes called "Ford Corporate Blue"). This enamel resists heat up to 550 degrees so it's a great paint to use on your engine. Dry to touch in 30 minutes and ready to handle in 1 hour. It's also resistant to all types of automotive fluid. Once you get this stuff on, it will not flake, crack or peel. ...

Scott Drake used the original Ford prints to makes these exactly as the originals with heavier gauge steel than the other reproductions we have seen. Unlike the reproductions of the past, these actually fit without the need for modification or the need to jump on the front of the car to install.  These are the best braces on the market today by far... Greatly reduces twisting of the chassis. Also strengthens the front end and helps reduce shock tower fatigue and cracking. Also available...

Scott Drake used the original Ford prints to makes these exactly as the originals with heavier gauge steel than the other reproductions we have seen. Unlike the reproductions of the past, these actually fit without the need for modification or the need to jump on the front of the car to install. They are the best braces on the market today by far... Greatly reduces twisting of the chassis. Also strengthens the front end and helps reduce shock tower fatigue and cracking. Also available in Black...

Scott Drake used the original Ford prints to makes these exactly as the originals with heavier gauge steel than the other reproductions we have seen. Unlike the reproductions of the past, these actually fit without the need for modification or the need to jump on the front of the car to install. They are the best braces on the market today by far... Greatly reduces twisting of the chassis. Also strengthens the front end and helps reduce shock tower fatigue and cracking. Also available in Black...

Fits 1967 and 1968 Standard or XR7

Sold as a Kit as Pictured.

Reproduction fender fastener kit for Mercury Cougar Standard and XR7.

Reproduction Fender Extension Stud & Nut Kit for the 67 - 69 Cougar or Mustang

These reproduction hood and hinge bolts and U nuts fir both the Standard and XR7.

Correct Fit and finish for 1967, and works for 1968. Connects the overhead roof console to the mounting bracket. The only difference between the 67 and 68 kits are that the 67 screws are chrome and the 68 are zinc. The zinc will discolor over time, so we suggest using the 67 kit on a 68. Replaces Ford Part #: 519A58

This reproduction quarter panel extension fastener kit fits both the Standard and XR7.

Our grade "A" fenders are truly what you would expect from an "A" rated part! We never get returns on our grade "A" fenders which is very important considering the shipping costs involved. Grade "A" fenders have no rust or excessive filler and nothing more than dings or light scrapes for damage. When you turn it over you will not see anything more than light surface rust and no distorted wheel lip areas from over sized tires rubbing. We really inspect the area where the fender extension bolts...

Our grade "B" fenders are often what many would consider Grade "A". "B" Grade fenders may have damage around the wheel lip from over sized tires or very minor rust at the bottom corner or a fixable dent but they will not have all of these. We know what body work costs and we do not save junk. We also have many fenders that would be considered grade B+ or A-, give us a call for detailed descriptions of what we currently have on hand. Keep in mind that when ordering multiple over-sized items...

This latest of a series of 67 reproduction sheet metal parts is just what the market has been waiting for! The dimensions are EXACT down to the 1/16", black primer finish is very similar to what the later service replacement parts were from Ford. The fender weighs a few pounds more than original due to being made from slightly thicker material than OEM. Keep in mind there are no shipping fees or taxes when you pick this item up in person at our shop. Next up will be deck lids, stay tuned!...