Body

Rear license plate and fuel door hinge pin for 1967-68 and 1971-73 Cougars and 1968-71 Ford Fairlane and Torino models, excluding station wagon and Ranchero. One pin for each side of the hinge, sold individually. Replaces Ford part # C6OZ-13432-A.

Used door hinge anchor plate for attaching the door hinge to the body pillar. Driver and passenger side lower only, kind of shaped like the State of Utah. Fits driver and passenger side hinges. Fits any 1967 Mercury Cougar and Ford Mustang. Ford part number 6502667.

Used door hinge anchor plate for attaching the door hinge to the body pillar. Driver and passenger side upper only. Fits any 1967 Mercury Cougar and Ford Mustang.Ford part number 6502666.

Floor tunnel body reinforcing plate for the floor shifter on any 1967-68 Mercury Cougar or 1965-68 Ford Mustang. Used plate spot welded to the underside of the floor. Has threaded inserts installed. Contoured differently than other years. We cut, you remove spot welds. Take your measurements for location, before removing your old floor and or tunnel.  Ford part number C5ZZ-6512118-A.

Our grade "A" rear quarter panel extensions have no obvious dings, scrapes, bumper contact damage or warping due to over tightening of studs. Ford casting # C7WB-6527703-A, Mercury MPC # C7WY-6528073-A. Do you have questions about your Cat's factory pinstriping? This link may help.

Our grade "B" rear quarter panel extensions tend to have one of the following; obvious ding, scrape, bumper contact damage or warping due to over tightening of studs. We will not send you junk but rather a part like what you see pictured here that needs only minor repairs to be show quality.  Ford part # C7WB-6527703-A Do you have questions about your Cat's factory pinstriping? This link may help. ...

Our grade "B" rear quarter panel extensions tend to have one of the following; obvious ding, scrape, bumper contact damage or warping due to over tightening of studs. We will not send you junk but rather a part like what you see pictured here that needs only minor repairs to be show quality. There are very slight differences between 1969 and 1970 and they do carry different part numbers. Ford part # C7WB-6527702-A, Mercury MPC # C9WY-6528072-A. Do you have questions about your Cat's factory...

Reproduction driver side rear quarter extension panel for the 67 - 68 Cougar. This is the panel that the quarter extension mounts to.

Reproduction passenger side rear quarter extension panel for the 67 - 68 Cougar. This is the panel that the quarter extension mounts to.

Crating Fee Applies To This Item. You will be contacted once your order is reviewed to discuss the crating fee. Crating fees generally run between $175 - $250 (this does not include truck freight charges). If an item has a crating fee, this usually indicates that it must ship via Truck Freight and can only be shipped to US addresses and select Canadian addresses. Here is our used grade "B" passenger (right hand) side quarter panel. We ask that you call to discuss condition, price, and cut...

Finally, a quality reproduction replacement quarter panel skin for the 67 - 68 Cougar! The days of searching for good used $1000 quarters are over. This new quarter panel skin is a direct fit. Die Stamped with Excellent Quality 19 Gauge Steel like the factory used.  This skin does not include the rear quarter extension panel, you can find it here. Replaces Ford part number C7WY-6527841-AKeep in mind that this item is over-sized and will cost about $275 to drop...

Finally, a quality reproduction replacement quarter panel skin for the 67 - 68 Cougar! The days of searching for good used $1000 quarters are over. This new quarter panel skin is a direct fit. Die Stamped with Excellent Quality 19 Gauge Steel like the factory used. This skin does not include the rear quarter extension panel, you can find it here.  Replaces Ford part number C7WY-6527840-AKeep in mind that this item is over-sized and will cost about $275 to drop ship a single...

This plasma cut patch was taken from the complete skin we list. We do this because not only do some customers not want to replace the entire skin, but often our foreign customers do not want to pay freight for an entire panel. Give us an outline if your requirements for a cut are are different from what is shown, and often we can accommodate.This is a "full" cut, which means that vertically it reaches from the bottom of the panel all the way to the top of the panel.You can find the...

This plasma cut patch was taken from the complete skin we list. We do this because not only do some customers not want to replace the entire skin, but often our foreign customers do not want to pay freight for an entire panel. Give us an outline if your requirements for a cut are are different from what is shown, and often we can accommodate.This is a "patch" cut, which means that vertically it reaches from the bottom of the panel to about 10" up.You can find the full versions here. ...

This plasma cut patch was taken from the complete skin we list. We do this because not only do some customers not want to replace the entire skin, but often our foreign customers do not want to pay freight for an entire panel. Give us an outline if yourrequirements for a cut are are different from what is shown, and often we can accommodate. This is a "full" cut, which means that vertically it reaches from the bottom of the panel all the way to the top of the panel. You can find...

This plasma cut patch was taken from the complete skin we list. We do this because not only do some customers not want to replace the entire skin, but often our foreign customers do not want to pay freight for an entire panel. Give us an outline if yourrequirements for a cut are are different from what is shown, and often we can accommodate. This is a "patch" cut, which means that vertically it reaches from the bottom of the panel to about 10" up. You can find the full versions...

This plasma cut patch was taken from the complete skin we list. We do this because not only do some customers not want to replace the entire skin, but often our foreign customers do not want to pay freight for an entire panel. Give us an outline if yourrequirements for a cut are are different from what is shown, and often we can accommodate. This is a "full" cut, which means that vertically it reaches from the bottom of the panel all the way to the top of the panel. You can find...

This plasma cut patch was taken from the complete skin we list. We do this because not only do some customers not want to replace the entire skin, but often our foreign customers do not want to pay freight for an entire panel. Give us an outline if your requirements for a cut are are different from what is shown, and often we can accommodate. This is a "full" cut, which means that vertically it reaches from the bottom of the panel all the way to the top of the panel....

Reproduction radiator / core support for Mercury Cougar and Ford Mustang. This is the very best one made! Replaces Ford part # C7ZZ-16138-B and C7ZZ-6510852-B together.

These are bolted to the rear frame rails and were used to tie the car down to the transporter for the journey from the factory to the dealer. The dealer was supposed to remove them and return them for a credit as instructed by the dealer. Notice the sticker on the rear license plate frame (decal is available in the decal section)? Many sets slipped through as the dealers often forgot or did not deem the small credit back worth their effort to remove. These are great for transporting your car...

For deck / trunk lids it is all about rust under the inner rear lip... We still check it over good for excessive filler, correct contour on all the lines and hidden rust under the weather strip. We ship deck / trunk lids with several layers of thick cardboard and insure them for the full amount. Keep in mind shipping is free if you order at the same time as a hood, door or quarter panel. For those wanting a cleaner look on their 1967-68 Cougar a 69-70 deck / trunk lid will bolt right on with...

Most often the problem with our Grade "B" deck / trunk lids is rust under the lip. We do not sell "rotted out" deck / trunk lids. Like the deck / trunk lid shown here you will be able to sand blast it and treat the rust so as to prevent it from spreading. We almost guarantee that at least "some" pin holes will appear after you have blasted the underside. Make sure to click onto our "after" shot to see what you should expect to see after you have bead blasted the underside of one of our "B"...

Used trunk or luggage compartment latch, fits all 1967-73 Mercury Cougar and many other Ford and Mercury cars. Comes with 3 bolts for mounting.Replaces Ford part number C5AZ-6243200-A.

Reproduction deck lid for the 67-68 Cougar. Exact reproductions of the originals, these deck lids are well fitting and are a perfect replacement for your old rusty lid.  Does not include hardware or lock cylinder, shipped bare. Here's the installation kit for these reproduction deck lids. Keep in mind that this is an oversized package and will most likely have to be shipped through truck freight. Expect to pay up to $250 in shipping charges. ...

Reproduction driver side rear extended floor pan for the 67 - 68 Cougar or Mustang. NOTE: This quality pan can be modified to fit a Cougar, but is designed for the Mustang. You can see in the picture above that when being installed on the Cougar, there will be a sizeable gap along the wheel well. We also carry used patches to fill those gaps ...

Reproduction passenger side rear extended floor pan for the 67 - 68 Cougar or Mustang. NOTE: This quality pan can be modified to fit a Cougar, but is designed for the Mustang. You can see in the picture above that when being installed on the Cougar, there will be a sizeable gap along the wheel well. We also carry used patches to fill those gaps. ...

Driver side, rear frame rail, from a 1967 Mercury Cougar. Full length, we cut so that there is some remaining metal on the edges. 1967 is unique, they use longer front leaf spring bolts. The leaf spring bolts on a 1967 Mercury Cougar go all the way through the rear frame rails. Ford part number C7WY-6510125-A.* Note - this item has dimensions in excess of 75 inches, and will ship as "Over- Size", unless you pick up in person. 

Passenger side, rear frame rail, from a 1967 Mercury Cougar. Full length, we cut so that there is some remaining metal on the edges. 1967 is unique, they use longer front leaf spring bolts. The leaf spring bolts on a 1967 Mercury Cougar go all the way through the rear frame rails. Ford part number C7WY-6510124-A.* Note - this item has dimensions in excess of 75 inches, and will ship as "Over- Size", unless you pick up in person. 

Reproduction driver side rear inner apron for both the Mercury Cougar and Ford Mustang.

Reproduction passenger side rear apron for Mercury Cougar and Ford Mustang.Here's a little film to help you fortify your flexxy feline!

All of our Standard and Decor, 1967 and 1968 rear interior panels come naked without the horizontal basket weave strip. We often will leave a yellowed, peeling one in place when they ship but if they are in good shape we remove them and sell them separately. If you purchase a panel from us and want a grade C strip, just mention it in the comments section of your online order and we will include it for free. Used driver side (left hand) rear interior panel in aqua for the standard Mercury...

All of our Standard and Decor, 1967 and 1968 rear interior panels come naked without the horizontal basket weave strip. We often will leave a yellowed, peeling one in place when they ship but if they are in good shape we remove them and sell them separately. If you purchase a panel from us and want a grade C strip, just mention it in the comments section of your online order and we will include it for free. Used passenger side (right hand) rear interior panel in aqua for the standard Mercury...

All of our Standard and Decor, 1967 and 1968 rear interior panels come naked without the horizontal basket weave strip. We often will leave a yellowed, peeling one in place when they ship but if they are in good shape we remove them and sell them separately. If you purchase a panel from us and want a grade C strip, just mention it in the comments section of your online order and we will include it for free. Used driver side (left hand) rear interior panel in black for the Mercury Cougar....

All of our Standard and Decor, 1967 and 1968 rear interior panels come naked without the horizontal basket weave strip. We often will leave a yellowed, peeling one in place when they ship but if they are in good shape we remove them and sell them separately. If you purchase a panel from us and want a grade C strip, just mention it in the comments section of your online order and we will include it for free. Used driver side (left hand) rear interior panel in blue for the standard Mercury...

All of our Standard and Decor, 1967 and 1968 rear interior panels come naked without the horizontal basket weave strip. We often will leave a yellowed, peeling one in place when they ship but if they are in good shape we remove them and sell them separately. If you purchase a panel from us and want a grade C strip, just mention it in the comments section of your online order and we will include it for free. Used passenger side (right hand) rear interior panel in blue for the standard Mercury...

Used driver side (left hand) rear interior panel in light ivy gold / light green for the standard Mercury Cougar. This unit will come with the basketweave strip intact, however the Mylar chrome trim will most likely be peeling. Because of a weak spot in the mold, all used panels may have a minor hairline crack where the rear seat meets the package tray. Only very early 1967 Cougars came without arm rests on the rear interior panel. If you need the unit without the arm rest holes you...

Used passenger side (right hand) rear interior panel in light ivy gold / light green for the standard Mercury Cougar. This unit will come with the basketweave strip intact, however the Mylar chrome trim will most likely be peeling. Also, because of a weak spot in the mold, all used panels may have a minor hairline crack where the rear seat meets the package tray. Only very early 1967 Cougars came without arm rests on the rear interior panel. If you need the unit without the arm rest...

All of our Standard and Decor, 1967 and 1968 rear interior panels come naked without the horizontal basket weave strip. We often will leave a yellowed, peeling one in place when they ship but if they are in good shape we remove them and sell them separately. If you purchase a panel from us and want a grade C strip, just mention it in the comments section of your online order and we will include it for free. Used driver side (left hand) rear interior panel in red for the standard Mercury...

[No Description Provided]

[No Description Provided]

Good used L bracket that is not heavily rusted or bent. Passenger side is marked from the factory with an "R" and driver side is marked with an "L". The portion with the lip mounts vertically and the purpose of the lip is to align the splash shield into the proper location.

Reproduction pair of lower fender braces. The portion with the lip mounts vertically and the purpose of the lip is to align the splash shield into the proper location.

Good used L bracket that is not heavily rusted or bent. Passenger side is marked from the factory with an "R" and driver side is marked with an "L". The portion with the lip mounts vertically and the purpose of the lip is to align the splash shield into the proper location.

Our grade "A" rear quarter panel extensions have no obvious dings, scrapes, bumper contact damage or warping due to over tightening of studs. Ford casting # C7WB-6527702-A, Mercury MPC # C7WY-6528072-A. Do you have questions about your Cat's factory pinstriping? This link may help.

New old stock passenger side rear quarter panel extension. 1967-68 Mercury Cougar. Ford casting # C7WB-6527702-A, Mercury MPC # C7WY-6528072-A. Do you have questions about your Cat's factory pinstriping? This link may help.

Rear fender splash shield for the driver side rear inner fender. In most cases, these used shields will need to have the stapled rubber shields replaced. Ford part # C7ZZ-16103-B. *Installation & detailing tip* Front fender splash shields are attached to the fender, rear shields are attached to the body. After the fender is installed, this is the right time to apply the undercoating material. This ensures that there is a good seal to prevent water splashing from the tires. ...

Rear fender splash shield for the passenger side rear inner fender. In most cases, these used shields will need to have the stapled rubber shields replaced. Ford part # C7ZZ-16102-B. *Installation & detailing tip* Front fender splash shields are attached to the fender, rear shields are attached to the body. After the fender is installed, this is the right time to apply the undercoating material. This ensures that there is a good seal to prevent water splashing from the tires. ...

Reproduction rear taillight panel lower structure / support for the 67 - 68 Cougar. This is a complete replacement for the factory spot-welded-in panel, not a partial cut. For more info on this new trunk panel, check out this video below: