Welcome to the NEW WCCC Cougar Parts Catalog (Tell us what you think)
Due to an Ice Storm our office/warehouse are currently without Phone/Internet (Power has been restored).
We will not be able to process/ship orders until our Phone/Internet are restored.
Current ETA for Phone/Internet to be restored are uncertain at this time.
Hours: Monday - Thursday 8am-5pm PST
$5* minimum website order
UK Customers: $250** minimum order (Read More)
loading . . .
'https://storeimages-westcoastclassic.netdna-ssl.com/dc/1000378/1344635707_e.jpg','https://storeimages-westcoastclassic.netdna-ssl.com/dc/1000378/1344635709_h.jpg','https://storeimages-westcoastclassic.netdna-ssl.com/dc/26221/1580759970_s.jpg'
  • Weatherstrip Seal - Rear Deck / Trunk Lid - Repro ~ 1967 - 1970 Mercury Cougar / 1965 - 1970 Ford Mustang - 26221
  • Weatherstrip Seal - Rear Deck / Trunk Lid - Repro ~ 1967 - 1970 Mercury Cougar / 1965 - 1970 Ford Mustang - 26221
  • Weatherstrip Seal - Rear Deck / Trunk Lid - Repro ~ 1967 - 1970 Mercury Cougar / 1965 - 1970 Ford Mustang - 26221

Item #: 26221

Login to add this item
to a saved wishlist
Price: $14.85
    Cost: 1188
    Earns: 15
    Bonus: 0

    Availability:

    Out of Stock, On Order - Less than 2 Weeks, Unless Supplier is Backordered

    Reproduction rear deck / trunk lid weatherstrip seal for the Mercury Cougar or Ford Mustang. A cheap piece that will keep water out and keep your trunk from rusting.



    Replaces Ford part #: C5ZZ-6543720.


    While you're in the trunk, you might also be replacing your trim. For some insight on the trim, check out our video below:


    Specifications:
    Shipping Weight: 1.00 LBS
    (weight shown may be the dimensional weight)

    4.94 out of 5 stars
    Based upon 25 Review(s).
    Virginia

    Great Product

    Material:
    Fit:
    Craftsmanship:
    Correctness:
    5.00 out of 5
    Pros:
    • Good Quality
    Cons:
    • No instructions
    Overall the seal appears to be of good quality. The only issue I had was that there were no instructions on which way to glue the seal on. It seems dumb that I could not figure out which direction to install the seal, however my old seal was brittle, hard as a rock, smashed and destroyed when I removed it so I did not have anything to compare it to or check proper fitment before I glued it on. The new one can be installed two different ways and again since i had the truck lid off and laying on a table I could not check which direction to install it. There are two flat sides on the seal, one just a little bit wider than the other. I took a guess and installed it with the wider side glued to the trunk and the narrower side away from the lid, this is NOT how it is supposed to be installed. So now the seal does not seal against the lip/rim on the body to make the seal. It would be nice to have a short note (with a cross section of seal) illustrating the proper way to install seal.

    Material:
    Fit:
    Craftsmanship:
    Correctness:
    5.00 out of 5
    Pros:
    Cons:
    Gasket formed as original and seems to be of good quality material.

    Georgia

    re: Weatherstrip Seal - Rear Deck / Trunk Lid - Repro ~ 1967 - 1970 Mercury Cougar

    Material:
    Fit:
    Craftsmanship:
    Correctness:
    4.75 out of 5
    Pros:
    • Quality
    Cons:
    • None
    '68 DGS. No issues with the w/s. Easy install, use patience and not too much adhesive; nice, thin, and even bead. It is cut to fit, so make that cut count!

    Weatherstrip Seal - Rear Deck

    Material:
    Fit:
    Craftsmanship:
    Correctness:
    4.75 out of 5
    Pros:
    Cons:
    • Seems a little less thick than OEM
    Haven't installed it yet but one thing I did notice is that it seems a little thinner than the original. Should work fine though. See picture to see the difference.

    St George, Ut

    Perfect in every way

    Material:
    Fit:
    Craftsmanship:
    Correctness:
    5.00 out of 5
    Pros:
    • quality
    Cons:
    Great customer service first of all, from now on I will be buying everything I can from here. shipping was fast, packaged well. Install went very smooth, I was worried because this part does not say it will fit a fastback mustang, but instead coupe/convertible. But it has plenty to make it around the trunk. The rubber is so soft, it sticks very well and immediately. I wiped the seal and deck lid with rubbing alcohol, let it dry, applied a thin line of 3m 08008(link) to both, spread out the lines to about ½ inch wide, let it tack up for a minute, then applied another thin line to the seal, spread it out and immediately put it in place. Zero movement of seal once placed down, and zero glue oozed out, looks perfect.

    Number of questions: 0
    Please login to ask a question.
    I3A03
    For your convinence, you can view this page on our old site by the following link:
    View Page On Old Site.