1968 Ford Mustang

Black plastic selector button for all 1973 Mercury Cougar and Ford Mustang with automatic transmission. It does not fit with the 1968-72 chromed T-handle.  Check out our video on rebuilding your shifter below: ...

Black plastic dummy button for all 1967 Mercury Cougar and 1965-67 Ford Mustang with automatic transmission. This is for all cars with body type 65A, 65C, 63A, or 76A. This is the non-moving button on the right side of your shifter handle. This is for all cars with body type 65A, 63A, or 76A. This is for the base model shifter handle. Deluxe shifters were larger and had simulated leather wrapping. Ford part C5ZZ-7C488-D.

Black plastic dummy button for all 1968-72 Mercury Cougar and Ford Mustang with automatic transmission. This is for all cars with body type 65A, 65C, 63A, or 76A. This is the non-moving button on the right side of your shifter handle. This is for all cars with body type 65A, 63A, or 76A. This is for the base model shifter handle. Deluxe shifters were larger and had faux leather wrapping. Ford part C8ZZ-7C488-A.

This reproduction knob set is made by Scott Drake Enterprises. Unlike our knobs, these units have a much larger font. Considering the average Classic Mustang owner is probably 50 years old or more, this was a pretty good idea to do them in this manner since the originals are rather hard to read while driving. If you want user friendly, then this is a very nice upgrade. If you want correctness, then our other set is what you will want. Either way, we got you covered.

Oil pressure sending unit 1967-68 Mercury Cougar and Ford Mustang 289/302 oil warning light style. This part actually goes back to 1956. Used on various Ford and Mercury engines from 1956-68. Clip on style wiring harness should be verified prior to purchase. *Note - Not for XR7Check out the video below on our new gauge tester: ...

Big bell shaped oil pressure sending unit for 1967 Mercury XR7 and 1967 Ford Mustang with actual oil pressure gauges instead of idiot light for the oil pressure. *Note - this pressure switch does use the 'nail head' connector. Please check your wiring harness for the proper connector.Replaced Ford part # C7ZA-9275-B Check out the video below on our new gauge tester: ...

Big bell shaped oil pressure sending unit for 1967-73 Mercury XR7 and 1967-73 Ford Mustang with actual oil pressure gauges instead of idiot light for the oil pressure. *Note - this pressure switch does use the press on wiring boot. Please check your wiring harness for the proper connector. This oil pressure sending unit also fits the following cars that have analog oil pressure gauges: 1969-71 Continental MKIII, Thunderbird 1965-71.Replaced Ford part # C9ZZ-9278-A Check out the video...

Oil pressure switch with press on wiring connector. 1967-73 Mercury Cougar and Ford Mustang. This is the warning light style of sending unit. Cougar body code 65A and 65C, excludes Eliminator. Additionally this sending unit also fits 1970 and newer Ford Maverick and Mercury Comet, 1968-69 Lincoln with 460 engines, and 1967-71 mid sized Ford and Mercury cars such as Cyclone, Fairlane, and Torino.Check out the video below on our new gauge tester: ...

Brass sensor that screws into intake manifold and activates temperature gauge in dash. Replaces Ford Part #: C6DZ-10884-B (SW-552) or C9WY-10884-A (SW-888)*. Temp Sender Switch Temp Rating : 15.2-19 Ohms Resistance At 220 Deg F Temperature Switch Thread Size : 3/8" x 18 NPT * - The 1969 351 Windsor temperature sending unit has been discontinued. Most manufacturers list the 1968 302 temperature sending unit as the closest replacement.Check out the video below on our new gauge tester: ...

These are correct reproductions of the A/C discharge service valve that comes with plastic caps. if you would like the correct aluminum valves, we sell those separately.

Used A/C discharge service valves for 1967-68 Mercury Cougars and Ford Mustangs equipped with factory or integral A/C. Original assembly line used high pressure or discharge valve for installation on either York or Tecumseh air compressors. Has the 3/4" inch flare fitting for suction hose. Note that this has the 'Flare' style of hose connection, also 'Rotolock' is used to describe this style of valve. We consider these core grade valves. They should be professionally inspected and...

Used A/C suction service valves for 1967-68 Mercury Cougars and Ford Mustangs equipped with factory or integral A/C. Original assembly line used low pressure or suction valve for installation on either York or Tecumseh air compressors. Has the 7/8" inch flare fitting for suction hose. Note that this has the 'Flare' style of hose connection, also 'Rotolock' is used to describe this style of valve. We consider these core grade valves. They should be professionally inspected and have...

Exact reproduction pair of originals and a must for that detailed engine compartment, but in stainless steel. It is little details like these that will often separate 1st from 2nd place at a show.Replaces Ford part # C5ZZ-19752-C.

Used servo cover from a 1967-68 Ford C-4 transmission. This cover has the big A cast into it, which designates it as an "A" Intermediate Servo Band Cover. Typically, this cover would be found on C4's, with Mercury Cougar and Ford Mustangs with C code 289-2V, A code 289-4V, or F code 302-2V engines. Cover only, marked C6AP-7D027-C.

Used servo cover from a 1968 Ford C-4 transmission. This cover has the big H cast into it, which designates it as an "H" Intermediate Servo Band Cover. Typically, this cover would be found on C4's, with Mercury Cougar and Ford Mustangs with J code 302-4V engines. Cover only, marked C8ZP-7D027-C.

Reproduction set of Deluxe seat belts for the 68 - 69 Cougar or Mustang Coupe. Some things you may want to notice are that although these are made to fit both 68 and 69, the webbing is the 68 style. 1968 belts had four rows of material that make up the belt and 1969 belts had three rows (as seen in the picture above). Also, the rear belts will not have the plastic sheaths that keep the belts from falling in between the seats. These belts are premium quality and come complete with deluxe...

378696-S Special set screw for the front door channel and vent window frame. This one is longer than the one that installs in the rear door window guide. This set screw has a 5/32" hex head with 5/16" NC threads and is 1-7/8 inches in overall length. This set screw also has a 1-1/8 inch diameter shoulder. Sets and holds your front door glass and vent window angle to allow a proper seal. Three set screws work in conjunction for each door glass and vent window combination. See your shop manual...

375694-S2 Special set screw for the rear door guide. This one is shorter than the two that install in the vent window frame and front door glass channel. This set screw has a 5/32" hex head with 5/16" NC threads, and is 1-9/16 inches in overall length. This set screw also has a ¾ inch diameter shoulder. Sets and holds your door glass angle to allow a proper seal. Three set screws work in conjunction for each door glass and vent window combination. See your shop manual for actual procedure.See...

New 8-32 set screw for the rear window crank handles. Fits 1968-70 Mercury Cougar and Ford Mustang. Allen hex size of 5/64".

Shaft or rod for the A/C damper blower door on any 1967-68 Mercury Cougar or Ford Mustang with factory or integral air conditioning. 1967-68 shaft is clocked differently than the 1969-73 version. This air conditioning damper door is in front of the blower or fan in the center of the car. Part cleaned for photograph, normally will ship 'as removed'. Inspected for damage or weakness of the metal. Shaft only, door not included, but available. See related parts.Replaces Ford part number...

Shaft or pivot pin for installing the drum brake pedal on any 1967 Mercury Cougar or Ford Mustang with automatic transmission. This is a reproduction of the 1968-70 shaft which had a Ford part number of C8AZ-2478-A. This version uses a special spring clip. We also sell the 1967 shaft, which uses a hairpin clip and washer.

Used shaft or pivot pin for installing the drum brake pedal on any 1967 Mercury Cougar or Ford Mustang with automatic transmission. We do not have the spring clip available. Ford part number of C8AZ-2478-A. 

WCCC no longer has an in-house service for tilt and tilt-tilt away steering columns 1967-1979. After several years of working exclusively with Tony Augustine in MO, we can highly recommend him as one of the most knowledgeable builders of these unique columns in the world.We now exclusively send all of the columns we sell as rebuilt to Tony for service.He can be reached at 816-210-4779 or 6t8cougarguy@gmail.com Make sure you tell him WCCC sent you!--- Don Rush, Owner of West Coast Classic...

Shaft or rod for air inlet damper door for any 1967-68 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The damper door allows re-circulating or fresh air to enter the fiber glass A/C box. Part cleaned for photograph, normally will ship 'as removed'. Inspected for damage or weakness of the metal. Shaft only, door not included, but available. See related parts.Replaces Ford part number C7ZZ-19C774-A.

Shaft or rod for the evaporator damper door on any 1967-68 Mercury Cougar or Ford Mustang with factory or integral air conditioning. 1967-68 shaft has a tab mounted on the lever, and is clocked differently than the 1969-73 version. The evaporator damper door allows air to pass over the evaporator in the fiber glass A/C box. Part cleaned for photograph, normally will ship 'as removed'. Inspected for damage or weakness of the metal. Shaft only, door not included, but available. See related...

Used lower shaft fixed steering column found from 1968-69 Mercury Cougar or Ford Mustang. This is the portion that mates with the upper shaft that bolts to the steering coupler. 1968-69 lower shafts are 15-1/2 inches in overall length. They also have a lower flange with flat sides. Other Ford fixed lower shafts can be used, in most cases the sheer pins are already broken. Just slide the shafts together for the desired length. WCCC no longer has an in-house service for tilt and tilt-tilt away...

Shaft or rod for the heater damper door on any 1967-68 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The heater damper door allows air to pass over the heater core in the fiber glass A/C box. Part cleaned for photograph, normally will ship 'as removed'. Inspected for damage or weakness of the metal. Shaft only, door not included, but available. See related parts.Replaces Ford part number C7ZZ-19C774-B.*Note will not work in 1969-73 A/C boxes.

Accelerator pedal shaft assembly that mounts to the engine firewall. For use with small block 1967-68 Cougars with C-4, automatic transmissions. This same assembly is used on small block Ford Mustangs 1966 - 1968. These assemblies are just the main shaft only, and do not come with the accelerator pedal or the throttle linkage. These made in Taiwan assemblies are pretty decent looking but for less money we have original FoMoCo which with a little TLC will look better and the fit is always...

Accelerator pedal shaft assembly that mounts to the engine firewall. For use with small block 1967-68 Cougars with manual transmissions. This same assembly is used on small block Ford Mustangs 1966 - 1968. These assemblies are just the main shaft only, and do not come with the accelerator pedal or the throttle linkage. These made in Taiwan assemblies are pretty decent looking but for less money we have original FoMoCo which with a little TLC will look better and the fit is always superior.Ford...

Used lower shaft used in the tilt / tilt away steering column found in the 1968-69 Mercury Cougar or Ford Mustang. This is the portion that mates with the upper shaft that bolts to the steering coupler. Overall length of this shaft is 15-11/16 inches long.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Used plastic sheath that covers the bolted buckle end of where your shoulder belt attaches to the roof section of your car. Sometimes when removing the bolt from your shoulder belt, this sheath will tear if the plastic has become stiffened. Although it does not affect it's usage, sometimes it's best to simply replace it.  NOTE: To remove this sheath, you will have to pull some slack from the seat belt up through the opening at the top in order to push up on the sheath to access the...

This 1967-68 Mercury Cougar and Ford Mustang shield, was installed at the factory to protect the heater motor from being damaged when the Big Block 390-427-428's were being dropped in. As noted in the factory assembly manuals we sell, they were supposed to be removed once the motor was in place. We have found that more often than not they were left in place as it was probably too time consuming to remove them. Technically they should not be in place on a concours car but practically...

This arm is attached to your automatic transmission floor shifter (see picture at left). Ford calls technical name for this part is 'Arm, Support'. These used parts will come with an intact bushing and nut. Correct for C-4 and C-6 transmissions. Ford part number C7ZZ-7302-A. ...

C5ZZ-7400-D4Assembly 4 Speed manual transmission shift control assembly for any 1967 Mercury Cougar and Ford Mustang. Small block 289 engines only. Includes shifter mechanism, shift rods, and shift lever. All in used condition.  Check out our video on rebuilding your shifter below: ...

This 4 Speed Lower Shift Boot attaches to the bottom side of your shifter to protect it from water and dirt. Fits the 67 and the 68 with 289 or 302 engines only Replaces Ford part #: C6ZZ-7138-C.

This reproduction of the 3 and 4 Speed Shift Boot has a metal core base just like original as is the texture. Fits the 67 and the 68. Replaces Ford number C5ZZ-7277-B. Customer feedback found at mercurycougar.net : When I bought my 68xr7 from Don two years ago, our deal was that he would keep the new Magnum 500's and BFG tires that were on the car. I asked him if he would just put some "rollers" on to get the car on and off my dad's trailer. When I got the car, he had put on a...

This bezel was never offered from the factory on a Cougar, but is a very attractive part for those with a manual transmission and no console. This unit works with three or four speed manual transmission and with a rubber or leather shift boot.

Original style, factory 3 speed lower shift boot.Replaces Ford part #: C6ZZ-7138-B

Attaches to the console shifter bezel on any 1967-68 Mercury Cougar or Ford Mustang. We occasionally have these available when we get broken console bezels. This shifter dial was originally attached with heat to a pin connector. To reattach we suggest using glue. These look like it would be easy to detail the white letters for P R N D 2 1 with a careful hand. May have a chipped corner that is not seen when installed. Ford part # C7ZA-7A213A Check out our video on rebuilding your shifter below: ...

Restored shifter T handle as found starting in 1968 and through, 1972 Mercury Cougar and Ford Mustang with automatic transmissions. This handle will actually fit on most Ford automatic floor shift levers of the era. Design is a little thicker in the body, compared to earlier designs. Core charge applies. Replaces Ford part number C8OZ-7213-A. Check out our video on rebuilding your shifter below: ...

Shift kit for the C4 transmission valve body for all 1967-67 Mercury Cougar and 1967-69 Ford and Mustang. This is a standard shift rebuilding kit for your stock valve body.

Shift kit for the C6 transmission valve body for all 1967-73 and 1967-73 Mercury and Ford. This is a standard shift rebuilding kit for your stock valve body.

Nice reproduction 3 speed black shift knob for the 1968 Mercury Cougar and Ford Mustang and other floor shift Ford products from 1968. Thread size is 7/16-20, will not fit on 1967. Ford part number C8OZ-7213-B. Check out our video on rebuilding your shifter below: ...

This one might cost a couple dollars more than others you may have seen but it is the best in my opinion. This is correct for a standard Cougar, XR7 had a woodgrained finish. Check out our video on rebuilding your shifter below: ...

Attractive knob used on later 68 through 69 non XR7 Cougars. I recently installed one of these on my own cars and had the face fall off the main body the first time I used it. I glued it back on and have had no problems since. Replaces Ford Part #: C8OZ-7213-A. Check out our video on rebuilding your shifter below: ...

Used on both XR7 and standard Cougar consoles. Differs from shifters made for non console use in that is has a small loop to connect the white plastic arm to the shift indicator light. Fits 1967-68 Mercury Cougar and Ford Mustang with factory consoles. Good used part no heavy pitting on the chrome, comes with complete with cable assembly inside. Ford part number C7ZZ-7210-C. Check out our video on rebuilding your shifter below: ...

Restored chrome automatic shifter lever for any 1967-68 Mercury Cougar or Ford Mustang with consoles. This console lever is unique to console equipped cars, it has a tab with a hole in it for accepting the shift indicator indicator rod. We sell these bare for those car owners that have pitted shifter levers. Ford part number C7ZZ-7210-C. *Note - Chromed lever only, sold without cable, pawl, handle, etc. Check out our video on rebuilding your shifter below: ...

Restored chrome automatic shifter lever for any 1967-68 Mercury Cougar or Ford Mustang without consoles. The 1967-68 is similar to the 1969-73 shift lever, but has the additional chrome window section for holding the indicator light. These have been re-chromed, we sell these bare for those car owners that have pitted shifter levers. Ford part number C7ZZ-7210-A. This lever was also used on the 1968 XR7-G cars with unique consoles.*Note - Chromed lever only, sold without cable, pawl, handle,...