Your cart is empty!
Our shopping cart requires the use of cookies. If you have your cookies disabled, please enable them for our site to place an order. If you have cookies enabled and have added an item to your cart, but you are still seeing this message, that could indicate that the cookie for our shopping cart is corrupted on your computer.You should be able to fix this by either:
Buy Details
Replaces Ford Part # C7SZ-3D600-A. Power steering pump adjusting spacer for use without air conditioning. For most 1967 - 1969 Mercury Cougar or Ford Mustang with 289, 302, 390, 428CJ engines, excludes 1969 351W and 1969 Boss 302 engines. Spacer dimensions: 7/16" I.D. x 1" O.D. and 9/16" thick.
Used exhaust manifold spacer with butterfly valve for use on 1967 to mid 1968 Mercury Cougar, Mercury Cyclone, Ford Fairlane, and Ford Mustang with 390 or 427-4V engines. Fully functional, we test these with a heat gun, they do open and close. These thermostat control valve assembly mates to the 1967 and 1968 passenger side 390 exhaust manifold up until about Feb 15, 1968. Easy to tell if it is needed with your manifold, no chamfer for the exhaust donuts at collector? you need this or a...
Replacement disc brake pedal mounting spacer. Correct diameter and length for installing disc brake pedals 1967-73 Mercury Cougar and Ford Mustang. About 2-1/8 inches long, correct I.D. and O.D. made from Moly steel. Basic Ford part number 2A188, the correct Mustang / Cougar number has been obsolete in the Ford MPC's for years.
Reproduction engine spacer plate and inspection cover for the 67 - 68 Cougar, Ford, or Mustang equipped with the 289 or 302 V8 with C-4 transmission (code W). 6 bolt bell housing. See related items for inspection cover plate by itself, or bell housing bolts, or inspection cover bolts. Replaces Ford part number C7AZ-7A008-E.
Reproduction spacer kit for your 1967 - 1969 Cougar or Mustang Midland power brake booster.
This brake booster to master cylinder spacer was used on many Ford / Lincoln / Mercury products beginning in 1962. Many do not even realize a foam filter is supposed to be sandwiched between the plastic filter cover and die cast aluminum spacer as brake fluid saturates them and the delicate foam filter element deteriorates. The originals were white but after many years become stained. Service replacement units were often black. These spacers were used on Thunderbird Cyclone Torino Fairlane...
Reproduction engine spacer plate for the 1967-68 Mercury Cougar or 1965-68 Ford Mustang equipped with the 289 or 302 V8 with C-4 transmissions (6 bolt only). This is for the 157 tooth flex plate and fits the C4 transmission bell housing. Replaces Ford part number C5ZZ-7007-A or C5OZ-7007-A.
Used engine spacer plate for the 1967-68 Mercury Cougar or 1965-68 Ford Mustang equipped with the 289 or 302 V8 with C-4 transmissions (6 bolt only). This is for the 157 tooth flex plate and fits the C4 transmission bell housing. Replaces Ford part number C5ZZ-7007-A or C5OZ-7007-A.
Early version of the FE engine / Transmission spacer plate. Has 1 medium sized hole instead of 3 smaller holes above the crankshaft. Originally was for either automatic or manual. Ford part #: C3AZ-7007-A.
1967-70 Cougars with any FE engine (390-2V, 390-4V, 427 GT-E, 428CJ, or 428SCJ) and with C6 automatic transmission or manual transmissions. Ford part #: C3AZ-7007-D.
Reproduction engine spacer plate for the 67 - 68 Cougar or Mustang equipped with the 289 V8 with manual transmissions (6 bolt only).Replaces Ford part number C5DZ-7007-A.
1967 1968 Cougar with 289 engines and a 3 or 4 speed manual transmissions. Will only work with 157 tooth bellhousings and flywheels. Replaces Ford part number C5DZ-7007-A.
Reproduction engine block spacer plate for 69 - 73 Cougars or Mustangs with 351 engines and 3 or 4 speed manual transmissions. According to the Master Parts Catalog, it also fits 164 tooth bellhousings on 1968-70 with 302 engines too. We also stock the early version from 1968 and 157 tooth versions.
Pair of reproduction sway bar mounting spacer plates, to be used with the 15/16 inch sway bar found on 427 4V / 428CJ / BOSS 302 cars.Mounts between the bracket and the frame mount.
This spring does NOT have correct spring finish or tension, but will work fine if you want to save a few $$$. Above is a comparison to this reproduction which is carried by other retailers, compared to our spring which is very close to the correct finish, length, and tension. Replaces Ford Part # : C8ZZ-17119-A ...
Original space saver tire from a 1968-70 Mercury Cougar or Ford Mustang with the elusive 7.35-14 size. These were optional in 1968-70. One RARE unit! Just looking for a space saver spare? We have much lower priced space savers with different sized / marked tires, and some with dual valve stems from the 1970's. Please inquire.Just the tire, perfect for someone who has a dated wheel.*NOTE* Does not include inflator bottle and valve caps are usually missing. ...
10 5/8" Spare Tire Mounting Bolt. Not 100% correct, but close replacement for the 1969 - 1973 with the 10 3/4" spare tire mounting bolt. Replaces Ford Part #: C8ZZ-1448-A, D0ZZ-1448-A & D1ZZ-1448-A.
Correct Autolite 45 spark plugs for all 1967-73 289/302/351W/390/428CJ engines. This is what Ford installed originally from the factory. BF32 crosses over to this spark plug. Typically these should have a electrode gap of 0.035", with either stock points or Pertronix ignition systems. Sold individually.
Keeps spark plug wires neat and orderly. Mounts on valve covers. Replaces Ford Part #: B8Q-12297-A.
These Spark Plug Wire Separators are made of high-quality ABS plastic. Constructed to hold both standard 7mm and 8mm high-performance spark plug wires. Fits directly on valve cover clip. Available in blue, red and OE black.
Made of heat resistant black nylon. Keeps spark plug wires neat and orderly.
Concours correct Autolite spark plug wires for any 1968 Mercury Cougar or Ford Mustang with 289 or 302 engines with thermactor smog systems. Black wires with 'Autolite', 'radio resistance', cylinder numbers individually imprinted, and 7mm wires. Orange spark plug boots on this set.
Concours correct Autolite spark plug wires for any 1968 Mercury Cougar or Ford Mustang with 390-4V, GT-E 427-4V, or 428CJ engines and with thermactor smog systems. Black wires with 'Autolite', 'radio resistance', cylinder numbers individually imprinted, and dated 4Q67 (fourth quarter 1967) on the 7mm wires. Orange spark plug boots on this set.Export cars, generally did not require smog in 1968.
Concours correct Autolite spark plug wires for any 1968 Mercury Cougar or Ford Mustang with 390-2V, 390-4V, or 428CJ engines without thermactor smog systems. Black wires with 'Autolite', 'radio resistance', cylinder numbers individually imprinted, and dated 2Q67 (second quarter 1967) on the 7mm wires. Black spark plug boots on this set, but with a orange boot for the number 6 plug wire. This was by plan, for a purposely crossed wire in the spark plug holder.Export cars generally did not have...
Not sure of the exact application for these original Ford stereo speaker wiring harnesses. We think that they may have come from the radio kits installed by Ford and Mercury dealers. Note the special speaker connector plugs. The individual right and left speaker wiring leads are about 40 inches in length from the center plug that goes to the radio or stereo. The paper tags are missing from these harnesses, but we are pretty sure that they begin with C8OA-19A041.One of our customers says that...
This correct replacement speedometer cable firewall grommet is manufactured using the original Ford blueprints and is a direct replacement for the factory grommet. Replaces Ford part number 380634-S.
New internal speedometer gear fits 4 speed toploader transmissions. Replaces Ford Part #: C5ZZ-17285-A.
Made out of Nylon. Please confirm teeth count and direction of teeth. Color codes do not guarantee direct replacement. 4 speed Toploaders have reversed tooth direction. Click here to use our Speedometer Gear Calculator. Available in 16, 17, 18, 19, 20, 21, and 23 tooth*. Replaces Ford Part: C0DZ-17271-A, C0DZ-17271-B, C0DZ-17271-C, C0DZ-17271-D, C0DD-17271-A, C1DZ-17271-A * - 23 tooth gears are not a Ford part and only have a life expectancy of 25,000 miles. They also have been reported to...
These four speed gears have the teeth reversed from the direction of the automatic gears. Made from Nylon. These gears only fit the 4 speed Toploaders. Click here to use our Speedometer Gear Calculator. Replaces Ford Part # : C2DZ-17271-G 20 Tooth Gear Pictured
These four speed gears have the teeth reversed from the direction of the automatic gears. Made from Nylon. These gears only fit the 4 speed Toploaders. Click here to use our Speedometer Gear Calculator. Replaces Ford Part # : C2DZ-17271-A 20 Tooth Gear Pictured
These four speed gears have the teeth reversed from the direction of the automatic gears. Made from Nylon. These gears only fit the 4 speed Toploaders. Click here to use our Speedometer Gear Calculator. Replaces Ford Part # : C2DZ-17271-B 20 Tooth Gear Pictured
These four speed gears have the teeth reversed from the direction of the automatic gears. Made from Nylon. These gears only fit the 4 speed Toploaders. Click here to use our Speedometer Gear Calculator. Replaces Ford Part # : C2DZ-17271-C 20 Tooth Gear Pictured
These four speed gears have the teeth reversed from the direction of the automatic gears. Made from Nylon. These gears only fit the 4 speed Toploaders. Click here to use our Speedometer Gear Calculator. Replaces Ford Part # : C2DZ-17271-D 20 Tooth Gear Pictured
This clip holds the speedometer cable gear to the end of the cable. Replaces Ford Part # : C1DZ-17292
Used speedometer cable from a 1967-68 Mercury Cougar or Ford Mustang with 3 speed manual transmission. These are assembly line used and would have had a Ford number of C7ZF-17260-E or C7DZ-17260-C. Has captured hold down bracket at transmission. These measure out about 58-13/16 inches long. Used condition, will have road grime, and maybe a couple of abrasions or small cracks in the casing. The internal cable has been tested and is good. Tags generally are not present on these. Look at the...
Unlike previous reproductions this has the correct grommet that passes through the firewall. 68 inches long replacement speedometer cable. New picture coming soon. Fits both C-4 and C-6 automatic transmissions for 1967-68 Mercury Cougar and Ford Mustang.Replaces Ford Part #: C7ZZ-17260-A.
Good quality, does have the built in rubber grommet that seals the cable as it passes through the firewall.
Formed metal clip that holds the gear end into any transmission. Automatic codes W - C4, X - FMX, U - C6, 1 - 3 speed manual, 5 or 6 - 4 speed manual.
Used clip with bolt for attaching the speedometer cable to the transmission of the Mercury Cougar or Ford Mustang. This unit holds the gear end into both automatic and manual transmissions. Automatic codes W - C4, X - FMX, U - C6, 1 - 3 speed manual, 5 or 6 - 4 speed manual.
Reproduction spool for the control valve on your 67 - 70 Cougar or Mustang.
Very close to correct spring finish (dark color) and tension. Above is a comparison to the other reproduction, which does not have the correct finish, is not the correct length, and does not have the correct tension. Replaces Ford Part # : C8ZZ-17119-A *Note* Must be used with the correct mounting bracket. See below. ...
This is the plastic center piece you press down to release your seat belt on the 68 - 72 seat belts. It comes unbroken and without cracks. This button piece has original decal with starburst design. Spring is included. Check out our video "All about seat belts" below.
Fits the 1967, 1968, 1969 and 1970 Mercury Cougar with the 390, 427, 428CJ or 428SCJ. These have the correct 20 coil spring, but are 1/8" longer than the Ford Master Parts Catalog calls for. Replaces Ford Part #:C7ZZ-7591-AR.