1968 Ford Mustang

NOS ink stamped Ford script. Connects PCV valve to carburetor spacer plate. For all 289-2V, 289-4, 302-2V, and 302-4V engines. Ford part number C6AZ-6A664-N. These were held on with wire clamps, available here. Fits 1967-68 Mercury Cougar and 1966-69 Ford Mustang. *Note – These molded and contoured hoses were designed to work with original style PCV valve (modern 90° PCV valves won't work). Additionally keep in mind that most anything other than period original intake manifolds, valve covers,...

C6AZ-6A664-N Original used hose that connects the original PCV valve to the carburetor spacer plate. All 289-2V, 289-4V, 302-2V, and 302-4V engines. Used hoses will have faded striping (if present), and clamp impressions. Very often the rubber will be hard and showing some degree of stress cracks. Application for mid year 1966 through 1969 289/302 engines, including Cougar, Mustang, Falcon, Galaxie, Fairlane, Torino, Cyclone, Ranchero, and Comet. *Note - These molded and contoured hoses were...

Concours correct with ink stamped Ford script. Connects PCV valve to carburetor spacer plate. For all 289-2V, 289-4, 302-2V, and 302-4V engines. Ford part number C6AZ-6A664-N. These were held on with wire clamps, available here. *Note – These molded and contoured hoses were designed to work with original style PCV valve (modern 90° PCV valves won't work). Additionally keep in mind that most anything other than period original intake manifolds, valve covers, and carburetor spacer...

Connects PCV valve to PCV transfer tube on the 390, 427-4V, and 428CJ. Inside diameter on one end is .45" the other end is .58". These should be tough to get on so that they will form a vacuum seal. Originally held on with wire clamps, we have those available here  Replaces Ford Part #: C8AZ-6A664-D. Fits Many 1966, 1967, 1968, 1969, and 1970 Mercury Monterey, Marquis, Ford Galaxie, with FE 390 Big Block Engines. We aren't sure why this hose was reproduced as shown. However it will...

This hose is the hose most Mustang / Cougar parts vendors offer. It is a rubber flex hose with economy fittings. Two required per vehicle, sold individually. We do not recommend these hoses and can not stand behind them as they often will leak if not torqued to the proper specs. Use caution when tightening these down as they are susceptible to stripping if you torque them to the specs called for by FORD. Replaces Ford Part #: C6OZ-3A714-A or C6OZ-3A717-A. ...

These are economy replacement hoses by Scott Drake. Aftermarket type hoses without original Ford markings in most cases. Made in the U.S.A. One piece design, meaning it differs from the original separate two piece pressure hose set. Upper and lower pressure hoses were what came on the cars originally. This hose is the hose most Mustang / Cougar parts vendors offer. It is a rubber flex hose with economy fittings. Use caution when tightening these down as they are susceptible to stripping if you...

These are economy replacement hoses by Scott Drake. Aftermarket type hoses without original Ford markings in most cases. Made in the U.S.A. This hose will work as a return line for either a small or big block 1967 - 1970. This hose is designed for a 2 piece return line application, so to make it work you will need to also purchase a chunk of generic hose. This is needed to connect this hose to your power steering pump.  Depending on the routing of your hoses you will need a different...

Water By-Pass Hose with Autolite® logo and part number imprinted in white ink. Stamped with C2OE-8597-A. Replaces Ford Part #: C7OZ-8597

The 1967 - 1968 windshield washer kit varies slightly from the 1969 - 1970. Replaces Ford part #: C7ZZ-17543.

Used front drum brake hose bracket for any 1967-70 Mercury Cougar or Ford Mustang. Simple bracket bolts to the front aprons and holds the brake hoses stationary. Right and left side are the same.Ford part number C1SS-2082-C.

Reproduction flex brake hose clip for the Mercury Cougar or Ford Mustang.

Power Steering hose bracket insulator for both the small and big block brackets for the 1967 - 1970 Mercury Cougar and Ford Mustang. Replaces Ford part #: C7ZZ-3A609-A or C7ZZ-3609. Customer feedback found at mercurycougar.net: Boy service is just not the same as the "good old"? days. I ordered a half a trunk load of parts and pieces from West Coast Classic Cougar and about 2 hours later got a phone call informing me that the order was picked and shipped. What are things coming to? Where is...

This is the 1967- 1968 retrofit or re-route hose kit! The tubing bends are all "spot on" and the portion that passes through the rubber insulator are identical to NOS for 1969. You will not find these at your local auto parts store or the the "Mustang Discount" folks. These hoses will also work on a 1967 or 1968 5/16" control valve fitting if it is routed the same as the big block. You will need to purchase the power steering hose bracket for the big block in order to make it work. This is a...

1967 - 1970 390, 427 and 428 & 1969 - 1970 302 and 351:  This is the correct control valve end hoses that comes from the power steering pump on all big blocks and the 1969 and 70 small blocks. This hose has industrial high pressure fittings that are much higher quality than those available by most Mustang / Cougar Parts Dealers. Includes both Pressure and Return hose that connect to the control valve. * 1967 - 1968 289 and 302:  This big block routing is far superior to the...

OEM routed power steering hose kit for the small block 1968. Includes the upper and lower hose. Click this link for more clarity on power steering hoses: https://secure.cougarpartscata...

These are economy replacement hoses by Scott Drake. Aftermarket type hoses without original Ford markings in most cases. Made in the U.S.A. This hose is the hose most Mustang / Cougar parts vendors offer. It is a rubber flex hose with economy fittings. Use caution when tightening these down as they are susceptible to stripping if you torque them to the specs called for by FORD. We do not recommend these hoses and can not stand behind them as they often will leak if not torqued to the proper...

Power steering hose kit w/ passenger cooler for the FE big block engines on the 67-70 Cougar or Mustang. Click this link for more clarity on power steering hoses: https://secure.cougarpartscata...

We are one of the only Mustang / Cougar vendors that carry "correct" power steering hoses for your early, big block Cougar or Mustang. The tubing bends are all "spot on" and the portion that passes through the rubber insulator are identical to NOS. You will not find all of these hoses at your local auto parts store or the the "Mustang Discount" folks. Fits the FE Big Block 390, 427 & 428 Mercury Cougar or Ford Mustang without Power Steering Cooler.   Click this link for more clarity...

CONCOURS radiator hose set, both upper and lower with C8ZE-8260-E and C8ZE-8266-E marked hoses. Used on both 20" and 24" inch radiators. For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check out our video:

Generic hose kit that will fit the 289 or 302 for those who are not concerned about the CONCOURS look. Used on both the 20" and 24" wide radiators Replaces Ford Part #'s C4ZE-8260-A and C4ZE-8286-A. For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check out our video: ...

New silicone radiator hoses for the 67 - 68 Cougar or Mustang with the 289 or 302 engine. The hoses are made with a sturdy black silicone, which will last longer than standard rubber hoses and has a higher burst pressure rating. Includes upper and lower radiator hose, and a bypass hose. To help enhance its performance, the lower hose is nylon-reinforced and comes with a stainless steel spring, which will keep this hose from collapsing and causing other problems. Used on both the 20"...

New silicone radiator hoses for the 69 - 70 Cougar or Mustang with the 390 or 428CJ engine. The hoses are made with a sturdy black silicone, which will last longer than standard rubber hoses and has a higher burst pressure rating. Includes upper and lower radiator hose, and a bypass hose. To help enhance its performance, the lower hose is nylon-reinforced and comes with a stainless steel spring, which will keep this hose from collapsing and causing other problems. Replaces Ford...

NOTE: Some Vendors show C8ZE for the upper hose, but C8WE is the correct stamping. These are the best CONCOURS radiator hoses on the market. All made in the U.S.A. by Gates or Goodyear both suppliers to Ford Motor Co, also approved by Mustang Club of America. All feature special white ink markings that have been designed to adhere to the hose under normal conditions, imprint will not come off even when in contact with antifreeze. All have imprints that are very crisp and authentic. Each...

These are the best CONCOURS radiator hoses on the market. All made in the U.S.A. by Gates or Goodyear, both of which were suppliers to Ford Motor Co in the day. They are approved by Mustang Club of America. All feature special white ink markings that have been designed to adhere to the hose under normal conditions, imprint will not come off even when in contact with antifreeze. All have imprints that are very crisp and authentic. Each imprint is CONCOURS correct for the specific application...

Reproduction Concours correct windshield washer hose with ribbed outer wall. Hose is 101" and is cut-to-fit. Tee connector not included, you can find it here. You can find the nozzles here.

No, zip ties were not used from the factory to secure the AC hoses to the shock tower braces . . . Four required per car, sold individually. Replaces Ford part #: C7ZA-430.

New front drum brake hub for all Mercury Cougars equipped with front drum brakes. Pretty much fits most front 5 lug 10 inch front drum brakes on all mid sized Ford and Mercury cars. Front drum brakes only. Fits 1967-69 Mercury Cougar and 1965-69 Ford Mustang with 5 lug 10 inch drums. Several manufacturers of the front drum assemblies such as Kelsey Hayes and Bendix were suppliers to Ford over the years. Quite a bit of labor to press these out. Needs threaded studs, see related...

Used front drum brake hub for all Mercury Cougars equipped with front drum brakes. Pretty much fits most front 5 lug 10 inch drum brakes on all mid sized Ford and Mercury cars. Front drum brakes only. Fits 1967-69 Mercury Cougar and 1965-69 Ford Mustang with 5 lug 10 inch drums. Several manufacturers of the front drum assemblies such as Kelsey Hayes and Bendix were suppliers to Ford over the years. Quite a bit of labor to press these out. May or may not have threaded studs, or...

Reproduction dog dish style hubcaps / wheel covers for the Mercury Cougar as well as other Mercury and Ford products. There are no less than three versions of this reproduction unit on the market. This one, in my opinion, is the best option. The hue is not as brilliant as the original, but a very nice cap for the fit and finish that it offers. We have trim rings available too! Check out our video on Legendary Wheels below: NOTE: These are for use on the Legendary Series Eliminator wheels Fits:...

The POGO Stick works just like the larger Hustler stick but is much easier to ship. If you need more leverage you can just add a pipe for leverage. We will loan this hustler stick for 60 days, with a 100% refundable purchase price. Tool must be returned in undamaged condition with no missing parts within the 60 day time period. Returns past 60 days are subject to a 25% restocking fee. Check out this video ...

C7OZ-3A697-A The most common power steering pump reservoir. Originally found on pumps with tag numbers: HBA-BF, HBA-BF1, and HBA-BR. These apply to 1967-69 Cougar and Mustang with power steering pumps originally installed on 289/302/390/427 and all 1968-1970 428CJ engines. Low pressure line nearly straight. *Note - Excludes 1969 302 & 351 engines. Our Grade A cans are far and few between as often folks like to use a pry bar as leverage to over tighten their belt. These cans will usually have...

C7OZ-3A697-A The most common power steering pump reservoir. Originally found on pumps with tag numbers: HBA-BF, HBA-BF1, and HBA-BR. These apply to 1967-69 Cougar and Mustang with power steering pumps originally installed on 289/302/390/427 and all 1968-1970 428CJ engines. Low pressure line nearly straight. *Note - Excludes 1969 302 & 351 engines. Our Grade B cans will always have some minor to moderate damage that is cosmetic. If you are capable of doing some minor body work they can made to...

Grade A Generic Ford power steering pump reservoir, has low pressure or return fitting point up. Check for hose clearance with your exhaust manifolds or headers on this reservoir. Fits 1967-69, and 1971-73 pumps with the small center hole for the pressure line. Most factory Ford pumps in 1970, had a larger hole, that was offset from center. Originally, these likely came from a full sized Ford car or pickup. Very common to find this style of reservoir on replacement power steering pumps. Our...

Grade B Generic Ford power steering pump reservoir, has low pressure or return fitting point up. Check for hose clearance with your exhaust manifolds or headers on this reservoir. Fits 1967-69, and 1971-73 pumps with the small center hole for the pressure line. Most factory Ford pumps in 1970, had a larger hole, that was offset from center. Originally, these likely came from a full sized Ford car or pickup. Very common to find this style of reservoir on replacement power steering pumps....

Tag marked HBA-BF or HBA-BF1 for use on 1967-68 Cougar and Mustang with power steering pumps originally installed on 289/302/390/427 and all 1968 428CJ engines. Various dates, and could be designated for either a Ford-Thompson (F) or TRW (W) power steering pump. For 1969 dated tags please see the related listing.*Please Note - Current inventory is exclusively 1967-68.

Reproduction idle mixture screw caps for Holley 4150 carburetors as found on 1967-70 Mercury Cougar and Ford Mustang. All white plastic caps. These were the tamper proof type of caps as installed from the factory.

Import reproduction. Fits 1967-70 Mercury Cougar or Ford Mustang without power steering. Rarely do these last the life of the rest of the front suspension, if you get 40,000 miles out of one you are lucky. The slightest amount of play in this component will translate to major slop in the steering. Click on images to enlarge. ...

Quality reproduction. Fits all 1967-70 Mercury Cougar and Ford Mustang. Rarely do these last the life of the rest of the front suspension, if you get 60,000 miles out of one you are lucky. The slightest amount of play in this component will translate to major slop in the steering. Lin, Hey, just wanted to thank you for your prompt service. Last Friday 4/24/09 I ordered a 71 - 73 Idler Arm and today (Monday 4/27/2009) I received it. WOW!!! I just wanted to let you know that you guys are...

NOTE - Some customer are experiencing problems with this economy idler arm, the castle nut on top is causing clearance issues with the bolt on the top arm.Import reproduction. Fits 1967-70 Mercury Cougar and Ford Mustang. Rarely do these last the life of the rest of the front suspension, if you get 40,000 miles out of one you are lucky. The slightest amount of play in this component will translate to major slop in the steering.

Premium grade of idler arm. Fits all 1967-70 Mercury Cougar and Ford Mustang. If you have loose / sloppy steering, replacing this part could help tighten things up. Rarely do these last the life of the rest of the front suspension, if you get 60,000 miles out of one you are lucky. The slightest amount of play in this component will translate to major slop in the steering. Drag link hole size: 5/8" Customer feedback: Hey, just wanted to thank you for your prompt service. Last Friday...

Sold individually # 377112-S

This used emergency / parking brake idler bracket welds to the under side of the floor on the driver side (left hand) of the vehicle. Will most likely be missing pin.

Air conditioning belt tension pulley. For Cougars and Mustangs with the 289 or 302 engine built between 1/3/1967 and 3/1/1968. These are all sold with new bearings. If your pulley only needs a bearing, don't sweat it. Click this BEARING link, we've got what you need! Ford part # C7AZ-8678-B. *NOTE* Must be used with the C7AA-2888-G cast iron lateral support brace. ...

Used A/C belt tensioning pulley with new bearing. Ford standardized some of the brackets starting in 1968. This adjustable bracket and pulley was used on all 1968-69 390 / 428CJ engines and 1968 289 and 302 engines after 3/1/1968. Additionally it was on 1969 351W engines as well. This adjustable tensioner pulley is identified by having the small bearing pulley. Same as the DOAZ-8678-C adjustable idler pulley only with a big bearing pulley. *Note* All new bearings will have a slight bit of play...

Service replacement A/C belt tensioning pulley with new installed bearing. This adjustable bracket and pulley can be used on all 1968 - 1973 Cougars or Mustangs with the V-8 engine as long as they have the "stamped steel" lateral air compressor support brackets. This bracket will only have the big bearing pulley and may have various casting numbers such as D5TA-8A617, D3OA-8A617, D5OA-8A617, D8OA-8A617, etc.*Note* All new bearings will have a slight bit of play in them. This is by design, by...

New sealed bearing for installing on your 1968-73 Mercury Cougar or Ford Mustang idler / tensioner pulley. This bearing also came in all of the "service replacement" idler pulley assemblies and is physically larger than the idler bearing for the 1968-69 only idler pulley (68-69 bearing sku: 10827). The center portion of the pulley, where this bearing would press into, has an inside diameter measurement of 1 9/16". On the smaller bearing pulley, this measurement is 1 3/8". Both versions of this...

New sealed bearing for installing on your 1968-69 Mercury Cougar or Ford Mustang idler / tensioner pulley. This bearing is physically smaller than the bearing used on the 1968-73 idler pulley (1968-73 bearing sku: 10462). The 1968-73 idler pulley assembly came as a "service replacement" on 1968-69 cars. The center portion of the pulley, where this bearing would press into, has an inside diameter measurement of 1 3/8". On the larger bearing pulley, this measurement is 1 9/16". Both versions of...

Used bracket and pulley assembly for Cougars and Mustangs with the 289 or 302 engine built after 3/1/1968. All pulleys are sold with new bearings installed.  If your pulley only needs a bearing, don't sweat it. Click this BEARING link, we've got what you need! We also offer a bearing replacement service to rebuild your 289 or 302 fixed idler pulley, see item 27539. Replaces part # C7AZ-8678-C. ...