1968 Ford Mustang

These quality mats are made in the USA by Auto Custom Carpets. They are a good fit with an aggressive grip rubber backing. These are heavy mats that will not easily slip out of place or become "wadded up" under your brake pedal. They will hold their form for many years and do more than just enhance the look of your Cougar, they will provide an extra layer of insulation providing an added barrier for heat and sound. Very nice carpet floor mats that make for an ideal gift for that Cougar lover...

This piece runs under the floor over the transmission where the floor pan meets the firewall.

Reproduction driver side (left hand) floor pan to cowl side panel for Mercury Cougar and Ford Mustang. Normal 0 false false false EN-US X-NONE X-NONE Here's our little film to help you fortify your car! ...

Good quality reproduction shifter assembly for all 1967-68 Mercury Cougar and Ford Mustang with consoles. NOTE: This assembly does not come with the lower bushing.

New fluorescent needle restoration paint for the gauges in your Mercury Cougar or Ford Mustang. Over the years, the sun has wreaked havoc on your Cat or Pony. This sun damage has also had it's way with the needles on you gauges and washed them out. This true fluorescent paint will not only make your needles look factory fresh, but will also bring back their glow at night. One jar contains 2.25ml worth of paint.

New manufactured flywheel for manual transmissions. Fits all 1967-68 Mercury Cougar and Ford Mustang with 289 engines with 3 or 4 speed manual transmissions. This flywheel has a 157 tooth ring gear. This flywheel will fit many other Ford small block V-8's with the 157 tooth gear.*Note - Most 1968 and newer Cougars came with 164 tooth flywheels, and they are not compatible.

This is a much cheaper version of the foil sound deadeners and underlays we sell. This particular insulation is basically bubble wrap with two layers of foil on both sides. Good for insulating headliners, floor pans, trunk areas, door panels, kick panels and just about anything else you might want to use it for. This insulation comes in a 48" X 72" roll. Just grab a pair of scissors and cut your shapes. You can use any adhesive you like (contact cement or weatherstrip adhesive,...

C7ZB-17664-A Foot operated electric wiper actuating device for engaging the windshield washer pump or to cycle your windshield wipers once manually in light rain. Ford MPC number C7ZZ-17664-A. For any 1967 - 1968 Mercury Cougar and Ford Mustang.NOTE: If your electrical points are fried, you can simply replace them with the used contact replacement kit.Please note the Core deposit ...

Windshield Washer Pump Pedal Pad for 1967-1968 Mustang & Cougar. Keep your foot from sliding off the pedal with this Injection-molded rubber pad with vertical grooves just like original. This pad was used on models with a floor mounted washer pump pedal. (7664A) This is almost always missing off of the end of your foot operated washer pump. Replaces Ford part number C7ZZ-17664-A. We also have good used pumps in stock.Thanks for the plug Mark!: My first deal with Don was clear back in the 1980s...

Reproduction rubber bumper that mounts to the metal axle snubber on Ford nine inch rear ends on 1967 - 1968 Mercury Cougar and Ford Mustangs. New part with a fine threaded stud, also called a pinion bumper. The correct casting number is seen on this rubber axle bumper is C3AA-4906-C, this version has fine threads. The version most often seen on the 1969-70 is C9OA-4906-A. It will have a course threaded mounting stud.

This USB flash drive contains the electronic collection of the 64 - 71 Ford Car and Truck Technical Service Bulletins (TSB) released from October 19th 1964 through September 10th 1971. Technical service bulletins are official communications between Ford and their dealerships that describe processes for troubleshooting or fixing certain common problems. TSB's document recommended procedures for repairing vehicles, when there are several occurrences of an unanticipated problem. TSB's can range...

Set of four in the box, no blemishes.Ford part number C8OZ-1130-COther Applications: Torino Fairlane Ranchero

Reproduction pair of frame rail / floor supports. These extend off the back of the front frame rail and give support under the front floor pan. Includes driver and passenger sides.

Reproduction driver side (left hand) inner front frame patch for Mercury Cougar and Ford Mustang. Will work for both coupe and convertible. Check out our video on front suspension and chassis upgrades below:

Reproduction passenger side (right hand) inner front frame patch for the Mercury Cougar or Ford Mustang. Will work for both coupe and convertible. Check out our video on front suspension and chassis upgrades below:

Steel freeze plug or expansion plug set for any Ford 390 / 427 / 428CJ engine. 1967-70 Mercury Cougar and 1967-70 Ford Mustang. 17 piece set with threaded screw in plugs as shown. 

Brass and steel freeze plug or expansion plug set for any Ford 390 / 427 / 428CJ engine. 1967-70 Mercury Cougar and 1967-70 Ford Mustang. 20 piece set with threaded screw in plugs as shown. 

Complete air vent assembly with cable, knob and bracket ready to bolt to your cowl. Replaces Ford Part # : C7ZZ-6501934-A

Our good used vents will not have cracks in the plastic or a rusty flapper from a leaking cowl. These are the same for AC and non AC.Replaces Ford part number C7ZZ-6501935-A.

This system features the "Original" Baer 2-piston, pad guided caliper (PGC) mounted to a 11.29", 1-piece slot, drill, zinc plated integral hub rotor. The PGC caliper comes in a red powder coated finish with a black logo, includes dust/weather seal's and uses the popular D412 pad type. The system includes premium bearings with races pre-installed, dust caps, mounting brackets, stainless braided hoses and all necessary hardware. The 11.29" "Classic" system fits select 14" and most 15" or larger...

This system features the "Original" Baer 2-piston, pad guided caliper (PGC) mounted to a 13", 1-piece slot, drill, zinc plated integral hub rotor. The PGC caliper comes in a red powder coated finish with a black logo, includes dust/weather seal's and uses the popular D412 pad type. The system includes premium bearings with races pre-installed, dust caps, mounting brackets, stainless braided hoses and all necessary hardware. The 13" "Classic" system fits select 17" or larger wheels....

There are a lot of choices out there when it comes to front end parts. There are numerous manufacturers on each part and some are priced very, very low. We do not like the quality of many of these discount parts and do not like selling them when we don't like using them on our own cars. We feel we can stand behind these quality products shown here. Note: Bright orange protective covers are to be removed before installation. KIT includes: (2) Lower Control Arms, (2) Upper Control Arms, (2)...

There are a lot of choices out there when it comes to front end parts. There are numerous manufacturers on each part and some are priced very, very low. We do not like the quality of many of these discount parts and do not like selling them when we don't like using them on our own cars. We feel we can stand behind these quality products shown here. KIT includes: (2) Lower Control Arms, (2) Upper Control Arms, (2) Outer Tie Rods, (2) Inner Tie Rods, (1) Idler Arm, (2) Spring Perches. If you...

Reproduction full one piece front frame rail for the driver side (left hand) of the Mercury Cougar or Ford Mustang. Replaces Ford Part #: C7ZZ-6510219-B.Here's our little film to help you fortify your flexxy feline!

FULL inner and outer passenger side (right hand) reproduction one piece frame rail for the Mercury Cougar or Ford Mustang. Replaces Ford Part #: C7ZZ-6510218-B.Here's our little film to help you fortify your flexxy feline!

Reproduction driver side front inner apron for both the Mercury Cougar and Ford Mustang.Here's a little film to help you fortify your flexxy feline!

Reproduction 22" pigtail for the 67-69 front turn signal wiring harness. Please Note: The Cougars are wired differently than some Mustangs. On some Mustangs the brown wire goes to a male plug.   This plug is a reproduction of the Cougar plug. Here is an example from the reproduction tail light we sell showing the difference: For installation on a Cougar, match up: Black Wire Black Wire Light Blue Wire Light Blue / Off White Wire Brown Wire Brown Wire ...

Replaces Ford Part # 359747-S

Used factory installed vented fuel, or gas cap as installed on 1967-69 Mercury Cougar 1970 cars without California emissions. Also fits 1969-70 Shelby Mustang. In 1970 California required a non-vented fuel cap.We stock these in limited quantities, and will have an intact paper gasket. Correct "VENTED" embossed and has the "S" stamped onto the center rivet. Price is established by demand, and these normally are only needed for very high level restorations or strict concours judging...

This filter ONLY fits the following 1967 - 1973 Cougars: the Boss 302 4V, 390 4V, 427 4V, 428 4V and the 429 4V. Will also fit many Mustang applications. Replaces Ford Part #: C7OZ-9155-A, Filter FG-19.

This filter ONLY fits the following Ford Holley 1967 - 1973 Cougars: the Boss 302 4V, 390 4V, 427 4V, 428 4V and the 429 4V. Will also fit many Mustang applications. This is a service replacement filter, it has D2AE-9155-AA stamped on the body of the filter. Replaces Ford Part #: C7OZ-9155-A, Filter FG-19 and C9AZ-9155-B,  FG-39.

This filter fits all V8 Mercury Cougars or Ford Mustangs with the Autolite Carburetor. This filter fits all 1967 - 1973 Cougars except for the following: the Boss 302 4V, 390 4V, 427 4V, 428 4V and the 429 4V. Will also fit many 6 cyl Mustang applications. These Filters are precisely designed and engineered to meet OEM requirements and fitment. Delivering high efficiency filtration, our filters meet modern engine demands for maximum fuel flow. Prevents harmful contaminants such as dirt,...

This filter fits all V8 Mercury Cougars or Ford Mustangs with the Autolite Carburetor. This filter fits all 1967 - 1973 Cougars except for the following: the Boss 302 4V, 390 4V, 427 4V, 428 4V and the 429 4V. Will also fit many 6 cyl Mustang applications. These Filters are precisely designed and engineered to meet OEM requirements and fitment. Delivering high efficiency filtration, our filters meet modern engine demands for maximum fuel flow. Prevents harmful contaminants such as dirt,...

Quality U.S.A. made hose with concours repeating GAS markings. Also include OEM mounting hardware. Replaces Ford Part #: C7ZZ-9327-A. Check out our video on replacing the fuel system on a '68 Cougar

This is the OE steel tube that goes from the Ford Holley carburetor to the Carter X fuel pump. This was copied to fit the vintage Ford Holley 4150 carburetors as originally found on 1968 390-4V, and 1968-70 428CJ engines. *Note - Designed to fit OEM Carter X fuel pump with screws holding two halves together. Modern Carter fuel pumps are crimped and will need some bending of this tube to fit. Please see item 11761 tube for use with generic Carter fuel pumps. **Note - Excludes 1969 390-4V with...

This is the steel tube that goes from the carburetor to the fuel pump. Designed to fit OEM Carter X fuel pump with screws holding two halves together. Modern Carter fuel pumps are crimped and will need some bending of this tube to fit. Please see item 11761 tube for use with generic Carter fuel pumps.

This is the steel tube that goes from the carburetor to the fuel pump on the 289 or 302 with the AutoLite 4300 4 barrel carberator. Original steel version.

This is the steel tube that goes from the carburetor to the fuel pump. OE Steel

This is the steel tube that goes from the carburetor to the fuel pump. Stainless Steel

This is the steel tube that goes from the carburetor to the fuel pump if you have a 289 or 302, and you have the Autolite 4300 4 Barrel Carburetor. Stainless Steel.

This is the steel tube that goes from the carburetor to the fuel pump. Available in original steel or stainless steel.

This is the steel tube that goes from the carburetor to the fuel pump.

Reproduction stainless steel line that runs from the fuel pump to the carburetor on your 68 Cougar or Mustang X Code equipped with a 390 2V engine.

This is the steel tube that goes from the carburetor to the fuel pump. Designed for vehicles LO-VOL fuel pump, fits 67 - 70 Mustang, 67 Cougar 390, 67 Fairlane and Torino.

Reproduction fuel pump for all 1967-70 Mercury Cougars and Ford Mustangs equipped with the 289, 302 or 351W engines. Be aware that this pump has a 3/8 inch fitting for the fuel line.

Reproduction fuel pump for all 1967-69 Mercury Cougars and Ford Mustangs equipped with either the 427 or 428 engine. Updated design from the originals, fuel lines fit the same.

Reproduction gasket for the vintage two piece Carter fuel pump bowl for the Mercury Cougar or Ford Mustang equipped with either the 390-4V, 427-4V or 428CJ engine.

For use with your original Carter fuel pump on Cougars equipped with a BOSS 302, GT 390, 428 Cobra Jet or 429 Cobra Jet.