Interior

Grade B condition - passenger side 'A' pillar pad, clips into the 'A' pillar post between the windshield and the door glass. Fits 1968 Mercury Cougar, passenger side only. Found on XR7 and most Standard model Cougars. Grade B condition, will some foam de-lamination on the back. Attaching clips sold separately. Please include desired color in the 'notes' or 'comments' section of your order. We can often supply your color, limited to available stock. For best results you should plan on...

These reproduction A pillarpads / moulding / trim were used on the 1967 - 1968 Mustang Coupe and Fastback and even though they carry a C7WB part number on the back side they were never used on a 67 or 68 Cougar. Reason being is they are two wide to fit next to the wide Cougar roof side Pinch weld moulding, soft trim. If you use the thin inexpensive pinch weld moulding we sell you can use these. Also note that the 1968 1/2 standard level interior used the thin pinch weld moulding from the...

Reproduction metal trim for filling the gap between the windshield and the dash pads on all 1967-68 Mercury Cougars and Ford Mustangs. This reproduction version is a copy of the 1968 moldings. 1968 mouldings were slightly shorter in length, due to the padded A pillars pads found on Cougar XR7's. 7 attaching screws are included. Ford part numbers C7ZZ-6504522-A and C7ZZ-6504523-A.

This two piece painted trim set helps to secure the dash pad in place at the bottom of the windshield. Fits 1968 Mercury Cougar only due to the larger padded 'A' pillar pads. Our used pieces taken from parts cars usually need to be painted but sometimes will pass as is for a driver quality car. We cannot promise we will have your color in stock but we will try to accommodate your request of color. These 1968 trim pieces also have a slightly textured painted finish, compared to the smooth...

Three required per car, held in place by Allen head bolt, fits in the three slots at the top of the column tube.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.Fits: 1968 Mercury Cougar1969 Mercury Cougar 1968 Ford Mustang1969 Ford Mustang ...

Steel plate for mounting the door pull or grab handle on 1967-68 Mercury Cougar XR7. Right and left is dependent upon which way the nylon inserts are installed. Comes complete as shown with nylon inserts for attaching the door pulls. The screws with 1/2 inch flat head for mounting this plate to the doors are also a available (three required).

This special bracket gets glued to the windshield. Rear view mirror bracket gets mounted to it. Glass bead blast it or just use a wire brush and it is ready to go!

Reproductions of the rare mounting kit brackets used to hold the shift indicator assembly to the console. The washer measures 1 13/16" x 5x8" and the total length of the screw is 1 3/8" but a much shorter screw would suffice. *NOTE* the raised lip of this washer faces up and only the three beveled holes on the shift indicator bezel use them.

We rarely have extras of these in stock but we like to show these items so you know what you are looking for or you can use it as a visual and fabricate your own kit. The washer measures 1 13/16" x 5x8" and the total length of the screw is 1 3/8" but a much shorter screw would suffice.Also available as a reproduction mounting kit. *NOTE* the raised lip of this washer faces up and only the three beveled holes on the shift indicator bezel use them. ...

Locking nut that attaches the shift lever to the shifter arm and support inside the shifter buckets. We normally see the fine threaded nuts on the 1967-70 shifters. Please check your shift arm support for correct threads.  3/8-24 threaded nut, serrated washer head style. Check out our video on rebuilding your shifter below: ...

Locking nut that attaches the shift lever to the shifter arm and support inside the shifter buckets. We normally see the fine threaded nuts on the 1967-70 shifters. Please check your shift arm support for correct threads. Check out our video on rebuilding your shifter below: ...

Unique shouldered screw that keeps your switch in perfect alignment, using incorrect screws will damage the switch.Fixed columns require 3 screws. Tilt columns require 2 screws.  *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of...

CRL brand glass bedding compound for installing the 1967-68 glass windshields and 1967-73 back glass that use rubber gaskets. This is a non-hardening material that seals the glass to the rubber

Four nuts per bucket seat, 8 total nuts per car with bucket seats. Sold individually. Replaces Ford part # 378643-S. Phosphate & Oil (gray & black) finish

Unlike our reproduction nuts these good used original nuts can be purchased individually and they cost less to boot! 8 required per car, 4 per bucket seat.

Perfect fit.

Correct nut that is designed not to come undone.

C7WB-13753-A Grade-A used screw on nut or bezel for the dash toggle switches on 1967-68 Mercury Cougar XR-7, 1971-73 Mercury Cougar, and 1969-70 Mustang Shelby console switches. This is a perfect used part, if you need an average quality used one mention it when you make your order and we will try and locate a free one for you.

Quality chrome and fit. Replaces Ford Part #: C7ZZ-11650-A. Here is a helpful youtube video on how to go about removing a headlight switch from a Cougar or Mustang. 

These nuts and little red insulators are needed when installing the factory Amp gauge. Sold as a pair (2 nuts and 2 insulators). 

New plastic nut or insert for those 1/4 inch square holes in the grille for attaching the headlight doors (8 required there), and for the XR7 door pull panel mounting plates for attaching the actual door handles (2 required per side). Replaces Ford part # 379830-S1. Check out this video ...

Reproduction overhead console bracket for the Mercury Cougar or Ford Mustang. This is a decent part, but not as good as the original FoMoCo part we offer.

This good used original front bracket for the over head console of the Mercury Cougar and Ford Mustang. This unit is better than the repro and was also used on 1967-68 Mustang fastback. We also have the clips that attach to the overhead console and then clip into this bracket. Ford Part #: C7ZZ-65519B46-A. *NOTE* 2 are required per car.

New product that is in stock and ready to ship! Unlike 1968 the 1967 xr7 console indicator light bar had no woodgrain applique. This will work fine on your 68 and some prefer the 1967 look over the 1968 version. We have a few of these with a 1968 Burl Wood Overlay applied to them. If you would like one of these, mention it in the order notes and if we have any remaining will send you one of these. These two pictures give you an idea what the lights will look like when illuminated. When not lit...

Rear bracket assembly for mounting the 1967-68 Mercury Cougar overhead consoles. Bracket spans the roof section of the car, felt covered padding on the roof side. DOES NOT INCLUDE small end brackets and clips. Main bracket has a Ford part number of C7WB-65519B24 *NOTE* Will not work for installing the long Mustang overhead consoles.

Rear bracket assembly for mounting the 1967-68 Mercury Cougar overhead consoles. Bracket spans the roof section of the car, felt covered padding on the roof side. Comes with both small end brackets and clips. Main bracket has a Ford part number of C7WB-65519B24 and the two smaller brackets have a part number of C7WB-65519B38. *NOTE* Will not work for installing the long Mustang overhead consoles.

New & Improved as of 2019! Woodgrain is now a near-exact match to the original.This steering wheel center decal is a near-perfect match to the original simulated burl wood grain used on the 1968 Cougar XR-7. To install, remove the metal insert from the steering wheel, separate it from the plastic trim border and carefully remove the walking cat emblem. Clean the surface with a wax & grease remover, isopropyl alcohol or similar. Then simply peel the new decal away from the backing,...

These decals are cut to fit the 1968 end caps. The 1967 end caps had a larger woodgrain insert without a black border. We also sell a slightly larger version of this kit for the 1967 owners. Simple peel-and-stick installation. Check out this video

Great for those wishing to shed a few pounds from their early Cougar as this insulation weighs less than one pound and the original weighed almost four pounds. If you want to keep your Cougar original then you will want to check out our used package tray sound deadener / insulation / jute. *NOTE* This is actually patterned for a 1968 Cougar, but will work in a 1967.

These fasteners were used to keep your package tray in place. In 1967 - 1968 two T shaped fasteners were held in place with a spring clip. Sold individually. Ford part number C4AB-6246698-A

Reproduction pair of package tray retainers for your 67 - 70 Cougar or Mustang. Made from stamped steel with a black finish to keep them from rusting. They install in the front of the package tray, keeping it secure.

Quality reproduction. Replaces Ford Part #: C5ZZ-7A624-B. Dear Lin Thurston, Hi, just wanted to let you know how impressed I am, to receive a package ordered on 6-6-07 and have it arrive on 6-13-07 all the way up here in Ontario Canada. That is impressive! Your shipping department is to be commended. I must say that the mail service worked at part of it, but the speed at which your firm addresses online orders from outside your country will keep me coming back for other items! Thank you, Phil...

Used Grade "A" over-head or roof console pad for any 1967-68 Mercury Cougar XR7. All of these pads will have minimal to no distortion or foam separation as shown in the photos. These came in a variety of colors, so be sure and include your desired color in the comments section of your online order. Other parts available and sold separately.Replaces Ford part number C7WY-65519A92 or C8WY-65519A92.

Used grade "B" over head or roof console pad for any 1967-68 Mercury Cougar XR7. All of these pads will have some distortion or foam separation as shown in the photos. These came in a variety of colors, so be sure and include your desired color in the comments section of your online order. Plan on using vinyl paint for improving the color, due to time, and UV light. Color vinyl pad only, other parts available and sold separately.Replaces Ford part number C7WY-65519A92 or C8WY-65519A92. ...

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. This SEM Trim Black paint is a satin black acrylic coating, formulated to match the OEM finish on automotive trim parts. Good for use on plastic, aluminum, steel, stainless steel and chrome. Great for refinishing grilles, taillight bezels, vinyl top trim, pinch weld blackout, and more.No primer...

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. New SEM aerosol flexable paint for the Mercury Cougar or Ford Mustang. This is a great match for the 1967, 1968 and 1969 dark blue interior color. SEM brand COLOR COAT is formulated to match, restore or change color on most vinyl surfaces, flexible and rigid plastics, carpet and velour. COLOR...

New pan head screws for installing the automatic console shifter bezel. Sold as a set of 4. Used in conjunction with the 3 metal strips to attach the automatic shifter bezel. Correct black pan head Phillips screw. *HINT - The metal strips can be made from any strips of steel, they don't really need the edges folded if you don't cinch them down too tight. Metal strip should be 1-11/16" x 5/8" with a hole in the middle.

This is a general listing for anything and everything seat belt related. We can't go through and list every single seat belt part we have here, but chances are, we have what you need. If you're looking for used belts, all you have to do is call our seat belt guy (his name is Junior, at extension 209) and he'll go out in the warehouse and put together a set to match your needs and price range. We have everything from dirty old faded belts with minor rust on the chrome, to super nice, clean,...

Reproduction pillar post mouldings that feature and vinyl overlay for the Mercury Cougar or Ford Mustang. These units are sold as a pair.

Used pin for the cable that goes to the vacuum motor used in actuating the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. Used only in the first part of 1968, later in the year this was upgraded to a clevis. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. Used pin for the locking lever in the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. Two are required in 1967-69, but only one is required for 1970 and up. Recommend changing to a up dated version of this pin with one that has circlips or snap rings (15-0156 for 1967 -69 or 15-0157 for 1970-1973) *NOTE* For tilt column service, you can contact Tony...

Pliable, soft used trim with no burns or nicks. 1967 is actually the same as 1968 but 1967 had a coat hook installed over the trim and it leave a permanent indentation that will not come out. Most 68's had this padded trim but the second half of 68 on standard models they used the small pinch-weld trim that we sell reproduction. If your wind-lace has shrunk up a little you probably will not be happy buying ours as most all of them shrink a half inch or so and it will be most evident where the...

Mostly Pliable, may have small burns or nicks. 1967 is actually the same as 1968 but 1967 had a coat hook installed over the trim and it leave a permanent indentation that will not come out. Most 68's had this padded trim but the second half of 68 on standard models they used the small pinch-weld trim that we sell reproduction. If your wind-lace has shrunk up a little you probably will not be happy buying ours as most all of them shrink a half inch or so and it will be most evident where the...

Pliable, soft used trim with no burns or nicks. 1967 is actually the same as 1968 but 1967 had a coat hook installed over the trim and it leave a permanent indentation that will not come out. Most 68's had this padded trim but the second half of 68 on standard models they used the small pinch-weld trim that we sell reproduction. If your wind-lace has shrunk up a little you probably will not be happy buying ours as most all of them shrink a half inch or so and it will be most evident where the...

Mostly Pliable, may have small burns or nicks. 1967 is actually the same as 1968 but 1967 had a coat hook installed over the trim and it leave a permanent indentation that will not come out. Most 68's had this padded trim but the second half of 68 on standard models they used the small pinch-weld trim that we sell reproduction. If your wind-lace has shrunk up a little you probably will not be happy buying ours as most all of them shrink a half inch or so and it will be most evident where the...

Reproduction pivot pin for the Mercury Cougar or Ford Mustang / Thunderbird equipped with a tilt / tilt away column. This is a pressed pin with a flange and 2 - 4 are required per car. Pin is custom made on short runs and is very difficult to find. .001 undersized, and with 8/32 threads instead of 6/32 like the originals. Newer pin removal tools will fit. Replaces Ford part # C7SZ-3D739-A. Removing pivot pins on 67 - 69 tilt away columns: Work on the upper knuckle pivot pins as there is room...

Used pivot pin for the Mercury Cougar or Ford Mustang / Thunderbird equipped with a tilt / tilt away column. This is a pressed pin with a flange and five are required per car. This pin is internally threaded with a # 6-32 thread. Ford part # C7SZ-3D739-A. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

1967-68 and 1971-73 Cougar/Mustang used bulb 1076 for Backup Lights, see part # 12175 As seen on Gearz with Stacey David. If you're looking for the best and brightest lighting for your car, look no further.  These WHITE "Plasma" LEDs are a direct replacement for 1156 and will fit anything you might have that takes an 1156 bulb (or other bulbs with the same base configuration, such as 97 and 1003 bulbs).  Basically good for every car from 1950 to 1990 that uses a 1156...