Interior

Aqua windlace or pinch weld moulding for any 1967-68 Mercury Cougar or Ford Mustang with factory console. Two of these short trim parts were fit to the very top of the plastic console base where the console meets the lower dash of your car. If these two parts are not in place you will have a gap. Original colors were Blue, Red, Gold, Saddle, Nugget Gold, Ivy Gold, and Aqua.  Sold individually. Ford part number C7ZZ-65045E18 or C8ZZ-65045E18.

Black windlace or pinch weld moulding for any 1967-68 Mercury Cougar or Ford Mustang with factory console. Two of these short trim parts were fit to the very top of the plastic console base where the console meets the lower dash of your car. If these two parts are not in place you will have a gap. See separate listing for color windlace. Sold individually. Ford part number C7ZZ-65045E18 or C8ZZ-65045E18. ...

Dark Blue windlace or pinch weld moulding for any 1967-68 Mercury Cougar or Ford Mustang with factory console. Two of these short trim parts were fit to the very top of the plastic console base where the console meets the lower dash of your car. If these two parts are not in place you will have a gap. Original colors were Blue, Red, Gold, Saddle, Nugget Gold, Ivy Gold, and Aqua.  Sold individually. Ford part number C7ZZ-65045E18 or C8ZZ-65045E18. ...

Dark Ivy Gold windlace or pinch weld moulding for any 1967-68 Mercury Cougar or Ford Mustang with factory console. Two of these short trim parts were fit to the very top of the plastic console base where the console meets the lower dash of your car. If these two parts are not in place you will have a gap. Original colors were Blue, Red, Gold, Saddle, Nugget Gold, Ivy Gold, and Aqua.  Sold individually. Ford part number C7ZZ-65045E18 or C8ZZ-65045E18. ...

Dark Red windlace or pinch weld moulding for any 1967-68 Mercury Cougar or Ford Mustang with factory console. Two of these short trim parts were fit to the very top of the plastic console base where the console meets the lower dash of your car. If these two parts are not in place you will have a gap. Original colors were Blue, Red, Gold, Saddle, Nugget Gold, Ivy Gold, and Aqua.  Sold individually. Ford part number C7ZZ-65045E18 or C8ZZ-65045E18. ...

Light Blue windlace or pinch weld moulding for any 1967-68 Mercury Cougar or Ford Mustang with factory console. Two of these short trim parts were fit to the very top of the plastic console base where the console meets the lower dash of your car. If these two parts are not in place you will have a gap. Original colors were Blue, Red, Gold, Saddle, Nugget Gold, Ivy Gold, and Aqua.  Sold individually. Ford part number C7ZZ-65045E18 or C8ZZ-65045E18. ...

Light Ivy Gold windlace or pinch weld moulding for any 1967-68 Mercury Cougar or Ford Mustang with factory console. Two of these short trim parts were fit to the very top of the plastic console base where the console meets the lower dash of your car. If these two parts are not in place you will have a gap. Original colors were Blue, Red, Gold, Saddle, Nugget Gold, Ivy Gold, and Aqua.  Sold individually. Ford part number C7ZZ-65045E18 or C8ZZ-65045E18. ...

Nugget Gold windlace or pinch weld moulding for any 1967-68 Mercury Cougar or Ford Mustang with factory console. Two of these short trim parts were fit to the very top of the plastic console base where the console meets the lower dash of your car. If these two parts are not in place you will have a gap. Original colors were Blue, Red, Gold, Saddle, Nugget Gold, Ivy Gold, and Aqua.  Sold individually. Ford part number C7ZZ-65045E18 or C8ZZ-65045E18. ...

Red windlace or pinch weld moulding for any 1967-68 Mercury Cougar or Ford Mustang with factory console. Two of these short trim parts were fit to the very top of the plastic console base where the console meets the lower dash of your car. If these two parts are not in place you will have a gap. Original colors were Blue, Red, Gold, Saddle, Nugget Gold, Ivy Gold, and Aqua.  Sold individually. Ford part number C7ZZ-65045E18 or C8ZZ-65045E18.

Saddle windlace or pinch weld moulding for any 1967-68 Mercury Cougar or Ford Mustang with factory console. Two of these short trim parts were fit to the very top of the plastic console base where the console meets the lower dash of your car. If these two parts are not in place you will have a gap. Original colors were Blue, Red, Gold, Saddle, Nugget Gold, Ivy Gold, and Aqua.  Sold individually. Ford part number C7ZZ-65045E18 or C8ZZ-65045E18.

White windlace or pinch weld moulding for any 1967-68 Mercury Cougar or Ford Mustang with factory console. Two of these short trim parts were fit to the very top of the plastic console base where the console meets the lower dash of your car. If these two parts are not in place you will have a gap. Original colors were Blue, Red, Gold, Saddle, Nugget Gold, Ivy Gold, and Aqua.  Sold individually. Ford part number C7ZZ-65045E18 or C8ZZ-65045E18.

Reproduction dark blue headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group option used a...

Reproduction dark blue rear interior panel windlace that helps hold the rear interior panels in place. It is also known as the pinch weld moulding. This one piece of windlace will fit on either the driver and passenger side and is about 2 total feet worth of windlace. You will have to trim this unit to fit and it should be about 20 inches when correctly trimmed. *NOTE* There are two types of this trim found in the 1967-68, the smooth or rough textured version like the one shown here. ...

Reproduction dark red rear interior panel windlace that helps hold the rear interior panels in place. It is also known as the pinch weld moulding. This one piece of windlace will fit on either the driver and passenger side and is about 2 total feet worth of windlace. You will have to trim this unit to fit and it should be about 20 inches when correctly trimmed. *NOTE* There are two types of this trim found in the 1967-68, the smooth or rough textured version like the one shown here. ...

Reproduction light blue headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group option used a...

Reproduction light blue rear interior panel windlace that helps hold the rear interior panels in place. It is also known as the pinch weld moulding. This one piece of windlace will fit on either the driver and passenger side and is about 2 total feet worth of windlace. You will have to trim this unit to fit and it should be about 20 inches when correctly trimmed. *NOTE* There are two types of this trim found in the 1967-68, the smooth or rough textured version like the one shown here. ...

Good used trim part that helps hold the rear panels in place. It is known as windlace or pinch weld moulding. There are two types of this trim found in the 1967-68, the rough or smooth textured version as shown. Please enter your desired color and texture into the comments section.

Reproduction saddle headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group option used a wider...

Reproduction saddle rear interior panel windlace that helps hold the rear interior panels in place. It is also known as the pinch weld moulding. This one piece of windlace will fit on either the driver and passenger side and is about 2 total feet worth of windlace. You will have to trim this unit to fit and it should be about 20 inches when correctly trimmed. *NOTE* There are two types of this trim found in the 1967-68, the smooth or rough textured version like the one shown here. ...

Reproduction white rear interior panel windlace that helps hold the rear interior panels in place. It is also known as the pinch weld moulding. This one piece of windlace will fit on either the driver and passenger side and is about 2 total feet worth of windlace. You will have to trim this unit to fit and it should be about 20 inches when correctly trimmed. *NOTE* There are two types of this trim found in the 1967-68, the smooth or rough textured version like the one shown here. ...

Show-quality triple chrome plated driver side quarter window frame for 1967-68 Cougars. These look awesome when restored, better than new. Mirror finish. We take your tired original window frames and have them professionally rechromed. Send your cores in advance to avoid the core charge, or wait until you receive your restored pieces to get reimbursed.Note: Badly pitted window frames may not be restorable, as the pits will need to be sanded out. If they are too deep, they may leave...

Show-quality triple chrome plated passenger side quarter window frame for 1967-68 Cougars. These look awesome when restored, better than new. Mirror finish. We take your tired original window frames and have them professionally rechromed. Send your cores in advance to avoid the core charge, or wait until you receive your restored pieces to get reimbursed. Note: Badly pitted window frames may not be restorable, as the pits will need to be sanded out. If they are too deep, they may leave...

This is actually not correct for a 1968 but it is all that is available in reproduction. The 1968 front is actually the same 4 1/4" length as the rear. Many people prefer the longer version as it makes it easier to roll up. We do have good used 1968 front cranks for those who prefer to stay with original. The portion that attaches to the splined shaft on the window regulator protrudes from the back 3/16" (as shown on the left in the comparison picture) and will not clear the 71-73 door panels...

C8AB-7630323-A Usually these will not have knobs. Plan on purchasing new knobs. Ask about our B grade knobs that will have some pitting or lusting issues. This is the correct "shorty" crank for a 1968 Cougar front window crank. It is the same length as the rear 1968 - 1970 but uses a center screw instead of a side Allen set screw. The 1969 - 1970 crank (with AM or no radio) looks the same but is longer. These shorter cranks were also used in conjunction with the factory door speakers used in...

Best quality of the three version made and the only one that comes with the decal installed. This is held on by an Allen set screw, we often get calls from people who cannot figure out how to remove these. Check our good used cranks if you like to keep original FoMoCo parts on your Cougar. Replaces Ford part number C8ZZ-6530322-A.

This is a good used original rear window crank with no obvious scratches or pitting. May or may not come with random colored knob. It most likely will be missing the decal but will have the original set screw. Ford part number is C8ZZ-6530322-A, casting number shown on back is C8ZB-6530323-A. Black knobs are the most commonly ones requested, plan on buying new knobs if you need black.

Easy to install quality reproduction. Sorry, aqua is not available at this time. Includes crescent spring and correct aluminum pin that features shoulder and locking knurls. Fits 1968-71 cars and about 1 month into 1972. Please see the window crank handles to see the difference between 1968-71 handles and 1972-73 window crank handles. Replaces Ford Part # C8AZ-6223352 *TIP* To install remove your window crank and place knob and crank in the jaws. To protect the knob you will want to place a...

Easy to install quality reproduction. Includes crescent spring and correct aluminum pin that features shoulder and locking knurls. Fits 1968-71 cars and about 1 month into 1972. Please see the window crank handles to see the difference between 1968-71 handles and 1972-73 window crank handles. Replaces Ford Part # C8AZ-6223352 *TIP* To install remove your window crank and place knob and crank in the jaws. To protect the knob you will want to place a clean rag over the jaws. Place a small socket...

Easy to install quality reproduction. Includes crescent spring and correct aluminum pin that features shoulder and locking knurls. Fits 1968-71 cars and about 1 month into 1972. Please see the window crank handles to see the difference between 1968-71 handles and 1972-73 window crank handles. Replaces Ford Part #C8AZ-6223352-GR *TIP* To install remove your window crank and place knob and crank in the jaws. To protect the knob you will want to place a clean rag over the jaws. Place a small...

Easy to install quality reproduction. Includes crescent spring and correct aluminum pin that features shoulder and locking knurls. Fits 1968-71 cars and about 1 month into 1972. Please see the window crank handles to see the difference between 1968-71 handles and 1972-73 window crank handles. Replaces Ford Part # C8AZ-6223352 *TIP* To install remove your window crank and place knob and crank in the jaws. To protect the knob you will want to place a clean rag over the jaws. Place a small socket...

Easy to install quality reproduction. Includes crescent spring and correct aluminum pin that features shoulder and locking knurls. Fits 1968-71 cars and about 1 month into 1972. Please see the window crank handles to see the difference between 1968-71 handles and 1972-73 window crank handles. Replaces Ford Part # C8AZ-6223352 *TIP* To install remove your window crank and place knob and crank in the jaws. To protect the knob you will want to place a clean rag over the jaws. Place a small socket...

Easy to install quality reproduction. Sorry, aqua is not available at this time. Includes crescent spring and correct aluminum pin that features shoulder and locking knurls. Fits 1968-71 cars and about 1 month into 1972. Please see the window crank handles to see the difference between 1968-71 handles and 1972-73 window crank handles. Replaces Ford Part # C8AZ-6223352 *TIP* To install remove your window crank and place knob and crank in the jaws. To protect the knob you will want to place a...

Easy to install quality reproduction. Includes crescent spring and correct aluminum pin that features shoulder and locking knurls. Fits 1968-71 cars and about 1 month into 1972. Please see the window crank handles to see the difference between 1968-71 handles and 1972-73 window crank handles. Replaces Ford Part # C8AZ-6223352 *TIP* To install remove your window crank and place knob and crank in the jaws. To protect the knob you will want to place a clean rag over the jaws. Place a small socket...

Protects door panels from the abrasive action of rotating handles. Made from a very hard nylon type material featuring the correct milky white color. Replaces Ford Part Number #C8AZ-6223370-ADiameter 1-1/2"

Used jumper wire used in the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Used upper wiring harness for the overhead console on the 67 - 68 Cougar XR7. Sometimes known as the Convenience Group Harness. This harness runs under the headliner from the overhead console back to the C pillar, where it connects to the lower harness. You can get the lower harness here. Ford Part Number C7WB-10C877-F

Reproduction tilt / tilt away steering column wiring harness for the Mercury Cougar or Ford Mustang. Exact copy in every way! If you call and tell us the long sad story of how when you pulled your column in 1982 in a bone yard and left this harness behind unknowingly. we will have to charge you extra... Just kidding! *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our...

Emergency or parking brake indicator lamp and wiring harness. Tested and working red indicator light which was found optionally on any 1968 Mercury Cougar standard model 65A or 65C. The 1968 parking brake light kit gets its power from the ignition switch. 

For use on fixed columns only. Attaches to the bottom side of the column to keep the wiring in place. Fits all 1968-69 Mercury Cougar, Ford Mustang, Ford Torino, Mercury Cyclone.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of...

Used radio light socket and wiring pigtail for all factory Philco AM radios as installed in 1967-70 Mercury Cougar and Ford Mustang cars. These light sockets are tested and cleaned, and have enough wiring lead to re-solder or crimp connect to your Philco AM radio. Original part with correct color wire.

Used steering column wiring harness plug aka Turn Signal Switch Harness Connector. Replacement plug for all 1970-72 Mercury Cougar and Ford Mustang, with tilt or fixed steering columns. Generic Ford part likely lots of applications between 1968-69, Ford, Mercury, & Lincoln. This plug is black, there is also a natural or white color version of this plug used by Ford 1968-69. Ford part number D0AZ-14489-L.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the...

Steering column wiring harness plug aka Turn Signal Switch Harness Connector. Replacement plug for all 1968 - 1969 Mercury Cougar and Ford Mustang, with tilt or fixed steering columns. Generic Ford part likely lots of applications between 1968 - 1969, Ford, Mercury, & Lincoln. Ford part number C8AZ-14489-S.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the...

Good used grade "A" core plastic passenger side bezel that may have had one or more very minor cracks repaired. One or more studs on the back may have been repaired as well. Finish will be poor or non existent but this bezel, unlike many we see will not have noticeable UV damage which makes them very brittle and prone to future damage.Check out our dash bezel repair video: ...

Good used core plastic bezel that has had one or more cracks repaired. Multiple studs on the back side will show repair work. Finish will be poor or non existent.Check out our dash bezel repair video: ...

Quality plexi-glass lens that is ready to install. Just peel off the protective tape and carefully pull your clock apart and replace and reassemble.The originals had a very slight concavity to them and these differ in that they are made from common, flat stock. These are also available already installed in our rebuilt clocks if you would prefer not to have to install the lens yourself.Check out the video below on our new gauge tester: ...

Reproduction XR7 Console Fastener Kit for the 1967 and 1968 Mercury Cougar

Fits 1968 Standard or XR7

New for December 2024! After a long wait these dash bezel kits are finally in production and hopefully will be in hand by Christmas (or shortly thereafter). As the seasoned Cougar owner will quickly point out, there are several differences between the 1967 and 1968 xr7 dash bezels. We have chosen to take the best elements of both years and combine them into one set as tooling to do both would be cost prohibitive. Without getting into the weeds, these dashes more closely resemble the 1968...