Interior

Reproduction headlight knob, retainer & bezel, cigar lighter and ignition switch retainer.

These studs and nuts are used to repair the passenger side mounting studs. The studs need to be drilled out using a 1/4" drill bit. Once done, use a 2 part epoxy and install the stud. Make sure to avoid getting epoxy on the threads where the nut will be installed. Once dry, install the bezel into the dash and use a 3/8 # deep well socket to install the nut. CAUTION: Only tighten finger tight to avoid cracking or breaking the bezel.

Used metal dash support brace for all 1967-68 Mercury Cougar and Ford Mustangs. Fastens to the lower flange of the metal dash panel and attaches to the inner cowl, 8-1/2 inches long. Viewed in the 1967 Osborn Body Assembly Manual on page 23. Replaces Ford part numbers C7ZB-6504672 or C7ZZ-6504672-A.

This 2 1/4" trim part installs directly above the steering column.

When removing this part resist the temptation to "open it up". Instead walk it off carefully leaving it in its factory position.

This unique to the 1968 standard Cougar trim set is what outlines the gauge cluster face pad. It is unique to the 1968 standard Cougar as it is held in place by spring clips. The 1967 trim set is held in by Phillips screws. Please note that AC cars have a unique design in that the long lower trim has a cut out for the AC vent. *NOTE* The spring clips that hold this trim to the dash bezels is very hard to come by. We usually have a few in stock but you may want to consider installing your dash...

This unique to the 1968 standard Cougar trim set is what outlines the gauge cluster face pad. It is unique to the 1968 standard Cougar as it is held in place by spring clips. The 1967 trim set is held in by Phillips screws. Please note that AC cars have a unique design in that the long lower trim has a cut out for the AC vent as shown here. *NOTE* The spring clips that hold this trim to the dash bezels is very hard to come by. We usually have a few in stock but you may want to consider...

This trim part starts to the upper left of the gauge cluster and continues on to the passenger side following the line of the upper padded dash.

Only for use on standard model Cougars with no A/C. This piece of trim affixes to the lower portion of the dash face pad and continues on towards the passenger side door.

Only for use on standard model Cougars with AC. This piece of trim affixes to the lower portion of the dash face pad and continues on towards the passenger side door.

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

This set of three woodgrain dash inserts for the Mercury Cougar equipped with A/C are the best of the best of which we can provide you with. These grade "A" inserts retain a rich, original looking finish and have not been subjected to prolonged damaging UV rays. We carefully match these under bright lights to ensure they match color wise. No scratches, dings or other blemishes, and all four toggle switch labels will be in place. Includes a brand new XR-7 emblem to make the dash really pop....

When purchasing this part from us it is best if you send in one of the dash parts you wish to match. The one pictured is the best we have to offer but the one that you need maybe faded which means a substantial savings depending on how faded of a bezel will be suitable for you needs. Prices for our less than stellar woodgrain parts usually run $25-$85 for the driver side. Check out our video on dash removal and restoration: ...

Used grade B driver side dash insert for the 67 - 68 XR7 Cougar. Will show some amount of fading and scratches. When purchasing this part from us it is best if you send in one of the dash parts you wish to match. The one pictured is the best we have to offer but the one that you need maybe faded which means a substantial savings depending on how faded of a bezel will be suitable for you needs. Prices for our less than stellar woodgrain parts usually run $25-$85 for the driver side. Check...

When purchasing this part from us it is best if you send in one of the dash parts you wish to match. The one pictured is the best we have to offer but the one that you need maybe faded which means a substantial savings depending on how faded of a bezel will be suitable for you needs. The best way to judge just how much fading has occurred on the panel is to remove the emblem for comparison purposes. Prices for our less than stellar woodgrain parts usually run $25-$85 for the driver side.Check...

Used grade B passenger side dash insert for the 67 - 68 XR7 Cougar. Will show some amount of fading and scratches. Emblem will most likely need to be replaced. When purchasing this part from us it is best if you send in one of the dash parts you wish to match. The one pictured is the best we have to offer but the one that you need maybe faded which means a substantial savings depending on how faded of a bezel will be suitable for you needs. The best way to judge just how much fading has...

New Tooling as of May 2016! The previous version had a heavier grain than original and had a built in defect / scratch on the driver side top. This new version is the best repro Cougar pad offered to date, satisfaction guaranteed. Reproduction dash pad in black for the 1967 and 1968 Mercury Cougar. This is the same Dashes Direct pad you see advertised elsewhere. Beware of the "other" brand of dash pad out there, it will not fit. First off I must say this is the best version of this much needed...

New Tooling as of May 2016! The previous version had a heavier grain than original and had a built in defect / scratch on the driver side top. This new version is the best repro Cougar pad offered to date, satisfaction guaranteed. Reproduction dash pad in BLUE for the 1967 and 1968 Mercury Cougar. This is the same Dashes Direct pad you see advertised elsewhere. Beware of the "other" brand of dash pad out there, it will not fit. First off I must say this is the best version of this much needed...

New Tooling as of May 2016! The previous version had a heavier grain than original and had a built in defect / scratch on the driver side top. This new version is the best repro Cougar pad offered to date, satisfaction guaranteed. Reproduction dash pad in DARK IVY GOLD or DARK GREEN for the 1967 and 1968 Mercury Cougar. This is the same Dashes Direct pad you see advertised elsewhere. Beware of the "other" brand of dash pad out there, it will not fit. First off I must say this is the best...

New Tooling as of May 2016! The previous version had a heavier grain than original and had a built in defect / scratch on the driver side top. This new version is the best repro Cougar pad offered to date, satisfaction guaranteed. Reproduction dash pad in DARK RED for the 1967 and 1968 Mercury Cougar. This is the same Dashes Direct pad you see advertised elsewhere. Beware of the "other" brand of dash pad out there, it will not fit. Please Note: Color on these is inconsistent and never spot on...

Good used original upper black dash pad. The pad shown is for a 1968 but will work a 1967. The difference is the 68 has a relief cut for the aluminum VIN tag located on the passenger side and 67 did not. Grade B dash will have no cracks, possible missing corner stud and not as soft and pliable as Grade A version. ...

Of the three covers used on the 67-73 Cougars we find this one the most difficult to use. Will Not Work On Badly Distorted Dash Pads. The problem is not with the product but rather the design of the original dash pad. Unlike the 69-73 pads the 67-68 pads are prone to warping (sagging) badly. Since this glue on shell is rather rigid you have to have a mostly straight pad to work with. Large cracks are no problem even if your pad is curling at the cracks, just break off the portions of your...

This used part comes carefully cut from a parts car and will include all mounting tabs. It is slightly different from the Mustang version as it has a different contour where the dash pad attaches. AC and no AC are the same, but 67 and 68 differ slightly in height of the area where the ashtray is installed.  

Excellent reproduction of the passenger side 1967-68 Mercury Standard Cougar "Cougar" dash panel emblem. Nice reproduction with locating pins that attach to the padded dash panel on the passenger side of all 1967-68 Standard model Cougars. The factory originally installed these emblems onto the padded dash panel, and melted over the pins to the back. Carefully remove the padded dash (clips or screws) and break off the melted tabs on the back of the emblem. Clean pad and reinstall the new...

Reproduction passenger side 1967-68 Mercury Cougar "Cougar XR7" dash panel emblem with chrome XR7 highlights. Nice reproduction with locating pins that attach to the woodgrain dash panel on the passenger side of all 1967-68 XR7's (excludes the special edition XR7-G models). The classic Cougar community voiced their opinion that the original emblems with satin silver was nice, but the chromed "XR 7" lettering in chrome makes the dash 'Pop' (see comparison photo above). The factory originally...

Excellent reproduction of the passenger side 1967-68 Mercury Cougar "Cougar XR7" dash panel emblem. Nice reproduction with locating pins that attach to the woodgrain dash panel on the passenger side of all 1967-68 XR7's (excludes the special edition XR7-G models). You can view the photo above for a comparison between the satin and chrome versions. The factory originally installed these emblems onto the woodgrain steel panel, and melted over the pins to the back. The rear section of that...

Reproduction heater dash plate for the 68 Cougar or Mustang. Included are the plate, 4 piece knobs and hardware. Keep in mind that this face plate has the pebble grain finish which was standard to Mustangs (Cougars had the smooth finish).

Good used dash toggle switch that operates the courtesy (rear opera) lights in the Mercury Cougar. These switches will have no rust or broken wires and the plastic toggle switch tips are sold separately. These used switches move freely and are guaranteed to work. The only real difference between the years, besides the size of the shaft, is the toggle switch tips. That is why we are offering both 1967 and 1968 versions. There are three versions of shafts used on the 1967 - 1968 XR7 toggle...

Good used dash toggle switch that operates the driver side (left hand) map light in the Mercury Cougar XR7. This switches will have no rust or broken wires, moves freely, and is guaranteed to work. Plastic toggle switch tip is sold separately. The only real difference between the years, besides the size of the shaft, is the toggle switch tips. That is why we are offering both 1967 and 1968 versions. There are three versions of shafts used on the 1967 - 1968 XR7 toggle switches and all three...

Good used dash toggle switch that operates the passenger side (right hand) map light in the Mercury Cougar XR7. These switches will have no rust or broken wires and the plastic toggle switch tips are sold separately. These used switches move freely and are guaranteed to work. The only real difference between the years, besides the size of the shaft, is the toggle switch tips. That is why we are offering both 1967 and 1968 versions. There are three versions of shafts used on the 1967 - 1968 XR7...

Good used dash toggle switch that operates panel (under dash) lights in the Mercury Cougar XR7. This switches will have no rust or broken wires, moves freely, and is guaranteed to work. The only real difference between the years, besides the size of the shaft, is the toggle switch tips. That is why we are offering both 1967 and 1968 versions. There are three versions of shafts used on the 1967 - 1968 XR7 toggle switches and all three feature the same C7WB-13713-A engineering number. 1967...

This is the decal used on the button of the female seatbelt buckle. Each seatbelt uses one of these.  Sold Individually Replaces Ford Part #: C8AZ-65611C02-A. Check out our video "All about seat belts" below. ...

Replaces Ford part #C8AZ-6223362-A. Sold in pairs, four required per car, used on most Ford products. We often get calls like "How do I remove my front window cranks?" Unlike the rear cranks that are held on by an Allen set screw, the fronts have a Phillips screw under this decal. If you are careful, often you can reuse your original and glue it back in place.

Used on both the speedometer and temperature / fuel gauge. Comes with plastic keeper washer that connects it from the backside of the lens. Sold individually, two required per cluster. These are in used condition as shown and need restoration.

Grade A used deluxe shifter handle in black. Nice used condition may have a hairline crack in the plastic on the bottom. No release button or set screw included. See related items for Grade B  Ford part number C8OZ-7213 The 67 version was actually a little different. Check out our video on rebuilding your shifter below: ...

Grade B used deluxe shifter handle various colors. Please specify color in the notes, limited to stock on hand. Fair used condition will have at least one crack in the plastic. May also have slightly pitted chrome. No release button or set screw included. See related items for Grade A  Ford part number C8OZ-7213 The 67 version was actually a little different. Check out our video on rebuilding your shifter below: ...

Used diffuser for the shift indicator lamp. This diffuser is used on the Cougar or Mustang WITH a console and attaches to the end of the light socket on your shift indicator wire harness. Both shift indicator lamps with or without a console used the same wire harness and socket, but used different diffusers. The difference in the harness from the 67 to the 68 was different colored wires and different plugs. Replacement bulbs can be found on our site as well. ...

Used diffuser for the shift indicator lamp. This diffuser is used on the Cougar or Mustang WITHOUT a console and attaches to the end of the light socket on your shift indicator wire harness. Both shift indicator lamps with or without a console used the same wire harness and socket, but used different diffusers. The only difference in the harness from the 67 to the 68 was different colored wires.

Used door / lid for the glove box in the 1967 Mercury Cougar or Ford Mustang. This unit is just the bare door / lid and does not come with the hinge, liner, lock or lock bezel. We have found this door on 1967 and into 1968 Cougars. Sometime in early 1968 this glove box door came with three holes on the back. Both glove box doors fully interchange. Bead blasted for the photo, door ships without rust, in most cases you will want to paint prior to installation.Ford part # C7ZZ-6506024-A.*NOTE*...

Used door / lid for the glove box on any 1968 Mercury Cougar or Ford Mustang. This unit is just the bare door / lid and does not come with the hinge, liner, lock or lock bezel. We have found this design of door with the 3 holes, well into the 1968 production run. 1967 and early 1968 doors are typically without the three holes on the back. Both glove box doors fully interchange. Bead blasted for the photo, door ships without rust, in most cases you will want to paint prior to installation.Ford...

Bulk pack of 100 oval head phillips screws for door and window crank handles.

Sold individually Zinc (dark silver)

The same plastic lock rod grommet but with a nice chrome finish for an extra touch. Sold in pairs. Replaces Ford Part #: C5DZ-6221999-B or C5DZ-6221999-C.

Good Reproduction of the clear plastic door lock grommets. Sold as a pair. Replaces Ford Part #: C5DZ-6221999-B.

Polished stainless steel with correct internal black felt anti-rattle pad. Sold as a pair.

Plastic injection molded, chrome plated like the originals. The detail on the top is not exact to original. Sold as a pair.Replaces Ford part number C8AZ-6221850-A

Made for Mustang but can be tweaked to work on Cougar. We advise you buy our good used rods. Replaces Ford part # C7ZZ-65213452.