Body

This kit is similar to the original type mounted in every drivers side door. These OEM style Riv-Nuts will be a challenge to install unless you have the special tool. Almost every body shop will have this rivet gun type of tool but here are a couple of ways to tackle the installation without the correct tool. Hole size is 1/4". Replaces Ford Part #: C7AZ-17696. Check out our video below for more info on mirror installation: Still have riv-nut questions? Here are riv-nut answers! ...

If what you are looking for is a sound deadener kit that fits and performs as good or better than the original... What you get when you order this kit is rather disappointing. For years we have not sold any underlay kits at all, we have just suggested you get your dose of disappointment closer to home and save the shipping costs or visit your local stereo store and see what high tech "cut to suit" materials they offer. Well, at least this listing will give you an honest idea of what you are...

5/16" thick sound deadening and heat reflecting material, comes in a 4' X 6' sheet that can be cut to fit. This insulation consists of two layers of polyethylene bubble film sandwiched between two layers of aluminum foil. Temperature range rated -60 deg. F. to 180 deg. F. Combining this with the tar-based sound deadener underlayment will result in similar sound deadening as the OEM sound deadener.Below is listed how many rolls you will need to underlay the sections of a Cougar:  Area...

This aluminum backed, tar sound deadener with adhesive is approximately 1/16 of an inch thick and works well behind door panels, at the firewall and under the headliner as a sound, heat and vapor barrier. One sheet required per door. Cut to fit, then remove paper backing to reveal adhesive, and stick in place. Comes in a 36 inch tall by 50 inch wide roll. *NOTE* Use caution when working with this product. The thin sheet of aluminum is quite sharp. We highly recommend using gloves. Before...

Pair of reproduction sway bar mounting spacer plates, to be used with the 15/16 inch sway bar found on 427 4V / 428CJ / BOSS 302 cars.Mounts between the bracket and the frame mount.

This spring does NOT have correct spring finish or tension, but will work fine if you want to save a few $$$. Above is a comparison to this reproduction which is carried by other retailers, compared to our spring which is very close to the correct finish, length, and tension. Replaces Ford Part # : C8ZZ-17119-A ...

Original space saver tire from a 1968-70 Mercury Cougar or Ford Mustang with the elusive 7.35-14 size. These were optional in 1968-70. One RARE unit! Just looking for a space saver spare? We have much lower priced space savers with different sized / marked tires, and some with dual valve stems from the 1970's. Please inquire.Just the tire, perfect for someone who has a dated wheel.*NOTE* Does not include inflator bottle and valve caps are usually missing. ...

10 5/8" Spare Tire Mounting Bolt. Not 100% correct, but close replacement for the 1969 - 1973 with the 10 3/4" spare tire mounting bolt. Replaces Ford Part #: C8ZZ-1448-A, D0ZZ-1448-A & D1ZZ-1448-A.

Reproduction original style chin spoiler. Nice quality, fit and finish. Made from thin plastic just like the originals. Comes as bare black plastic, so we suggest coating with your favorite semi-gloss black paint for a more finished look. Take a look at the 1:33:00 mark in the video below to see how we compare the reproduction to the original: ...

Show quality, correct weight and markings. Sold individually.

Very close to correct spring finish (dark color) and tension. Above is a comparison to the other reproduction, which does not have the correct finish, is not the correct length, and does not have the correct tension. Replaces Ford Part # : C8ZZ-17119-A *Note* Must be used with the correct mounting bracket. See below. ...

Reproduction hood hinge spring for all 1967-69 Mercury Cougars and 1964-70 Ford Mustangs. Common on many Ford and Mercury cars, this spring has 14 coils like the originals. We've found these springs to be of lesser quality than the originals, and they will stretch over time and not hold the hood up very well. We highly recommend you stick with original OEM springs. No returns on these springs. Click here to see our listing for good used originals. Replaces Ford part # C3OZ-16789-A. You can...

Coil hood hinge spring, 5-13/32" in overall length, 14 coils, coil diameter 1.899 inches. Sold individually, one per side. Other applications include:  1967-69 Mercury Cougar1967-70 Ford Mustang1965-69 Torino, Fairlane, Ranchero1965-70 Falcon 1965-66 Falcon Ranchero Ford part # C3OZ-16789-A. You can find the hood hinge apron nuts here.Anghel Restorations offers a very detailed breakdown of the differences in the Cougar and Mustang hood hinges. ...

Set of 20 replacement staples for the beltline kit. These are used to attach the beltline pieces to the door panel. Will work for any beltline kit on a number of different makes and models.

Quality reproduction stone guard for the 1969 Cougar. This unit is also known as a bumper filler, rock guard, or filler panelReplaces Ford part # C9WY-17779-A.

Price does not always dictate value... Our grade "B" stone deflectors have very minimal, easy to fix damage. The damage is most often found on the corners and would be hard to detect often times even if you chose not to fix them at all. Due to the flat, simple design of these stone deflectors most people with little or no experience in body work would be capable of making them look new again. We guarantee you will not find and rust (other than surface) and no signs of excessive filler. We have...

We rarely have this panel in stock in grade "A" condition, so we suggest you look close at our grade "B" panels as they need very little attention to become perfect. This unit is also known as a bumper filler, rock guard, or filler panelFord part # C9WY-17779-A.

Reproduction hood stripe kit in black for the hood of the Mercury Cougar equipped with the 351 engine. This vinyl stripe kit features the Cougar Head logo. *NOTE: The hood stripe with the Cougar head was originally specific to 69 Cougarsequipped with the 428CJ, and was also available on 69 Cougars equipped withthe 351 w/ Competition Handling Package.There's a fun fact filled thread on hood stripes on the Cougar forum, which you can find here. ...

Reproduction hood stripe kit in silver for the hood of the Mercury Cougar equipped with the 351 engine. This vinyl stripe kit features the Cougar Head logo. NOTE: The hood stripe with the Cougar head was originally specific to 69 Cougarsequipped with the 428CJ, and was also available on 69 Cougars equipped withthe 351 w/ Competition Handling Package.There's a fun fact filled thread on hood stripes on the Cougar forum, which you can find here. ...

Reproduction hood stripe kit in black for the hood of the Mercury Cougar equipped with the 428 engine. This vinyl stripe kit features the Cougar Head logo. NOTE: The hood stripe with the Cougar head was originally specific to 69 Cougarsequipped with the 428CJ, and was also available on 69 Cougars equipped withthe 351 w/ Competition Handling Package.There's a fun fact filled thread on hood stripes on the Cougar forum, which you can find here. ...

Our reproduction 428 CJ hood stripe kit in sliver with the black Cougar Head is made from quality 3M stock and patterned from an original Ford kit. Check out our video below showing how to install this hood stripe. NOTE: The hood stripe with the Cougar head was originally specific to 69 Cougarsequipped with the 428CJ, and was also available on 69 Cougars equipped withthe 351 w/ Competition Handling Package. There's a fun fact filled thread on hood stripes on the Cougar forum, which you can...

Our reproduction 428 CJ hood stripe kit with the black Cougar Head is made from quality 3M stock and patterned from an original Ford kit. Check out our video below showing how to install this hood stripe. NOTE: The hood stripe with the Cougar head was originally specific to 69 Cougarsequipped with the 428CJ, and was also available on 69 Cougars equipped withthe 351 w/ Competition Handling Package. There's a fun fact filled thread on hood stripes on the Cougar forum, which you can find...

Reproduction black hood stripe with silver Cougar head for the 1969 Cougar with the 351 engine. NOTE: The hood stripe with the Cougar head was originally specific to 69 Cougarsequipped with the 428CJ, and was also available on 69 Cougars equipped withthe 351 w/ Competition Handling Package.There's a fun fact filled thread on hood stripes on the Cougar forum, which you can find here. ...

Reproduction silver hood stripe with black Cougar head for the 1969 Cougar with the 351 engine. NOTE: The hood stripe with the Cougar head was originally specific to 69 Cougarsequipped with the 428CJ, and was also available on 69 Cougars equipped withthe 351 w/ Competition Handling Package. There's a fun fact filled thread on hood stripes on the Cougar forum, which you can find here. ...

Reproduction white hood stripe with black Cougar head for the 1969 Cougar with the 351 engine. NOTE: The hood stripe with the Cougar head was originally specific to 69 Cougarsequipped with the 428CJ, and was also available on 69 Cougars equipped withthe 351 w/ Competition Handling Package.There's a fun fact filled thread on hood stripes on the Cougar forum, which you can find here. ...

Reproduction black hood stripe with NO COUGAR HEAD for the 1969 Cougar with the 351W engine. NOTE: The hood stripe with the Cougar head was originally specific to 69 Cougarsequipped with the 428CJ, and was also available on 69 Cougars equipped withthe 351 w/ Competition Handling Package.There's a fun fact filled thread on hood stripes on the Cougar forum, which you can find here. ...

Reproduction black hood stripe with silver Cougar head for the 1969 Cougar with the 428CJ engine. NOTE: The hood stripe with the Cougar head was originally specific to 69 Cougarsequipped with the 428CJ, and was also available on 69 Cougars equipped withthe 351 w/ Competition Handling Package. There's a fun fact filled thread on hood stripes on the Cougar forum, which you can find here. ...

Reproduction silver hood stripe with black Cougar head for the 1969 Cougar with the 428CJ engine. NOTE: The hood stripe with the Cougar head was originally specific to 69 Cougarsequipped with the 428CJ, and was also available on 69 Cougars equipped withthe 351 w/ Competition Handling Package.There's a fun fact filled thread on hood stripes on the Cougar forum, which you can find here. ...

Reproduction white hood stripe with black Cougar head for the 1969 Cougar with the 428CJ engine. NOTE: The hood stripe with the Cougar head was originally specific to 69 Cougarsequipped with the 428CJ, and was also available on 69 Cougars equipped withthe 351 w/ Competition Handling Package.There's a fun fact filled thread on hood stripes on the Cougar forum, which you can find here. ...

Reproduction driver side (left hand) strut rod brace / support for Mercury Cougar and Ford Mustang.Replaces Ford # C8ZZ-03487-A.

Reproduction passenger side (right hand) strut rod brace / support for Mercury Cougar and Ford Mustang.Replaces Ford # C8ZZ-03486-A.

This kit mounts the spoiler pedestals to the trunk lid. Studs measure 2-3/4" long, correct for the Concours correct stands.Some economy or generic kits come with 1-1/2" studs

Used single hole front mount center visor bracket for the 1969 / 1970 Mercury Cougar and Ford Mustang hard tops.  The colors don't always match the seat color, so plan on spraying these with vinyl paint to match your interior. We often times can supply your desired color, mention your desired color in the 'comments' section of your order. Ford part # C9AZ-6204132, casting # C9AB-6204132-B.

Used 2 hole front mount center bracket for the sun visors in the 69 - 70 Mercury Cougar or 68 - 70 Ford Mustang convertible. The Master Parts Catalog (MPC) shows a specific part for the convertibles, but we have found three different styles of the sun visor arm clips used in the 68 - 70 convertibles.  Casting# C8OB-6304132-A has no dividerCasting# C8ZB-6504132-A has a partial divider (Most Common)Casting# C8ZB-6504132-B has a complete divider.  The colors don't always...

Reproduction single hole front mount center visor bracket for the 1969 and 1970 Mercury Cougar or Ford Mustang. This is a decent reproduction, but not quite as nice as the originals. Reproductions only come in 'paint to suit' black but we have most original colors in used. Replaces Ford Part #: C9AZ-6204132.

Reproduction sun visors that are fully padded and covered with the correct textured vinyl to match the seats. These units are sold as a pair.

Pair of reproduction cowl vent panel support pads.

This is the Left hand or driver side spring that holds the rear license plate or fuel door in the upright position. Fits all years of Cougar and 1966-71 Torino and Fairlane models except Station wagon and RancheroFord Part #: C7WY-13455-B

New Old Stock Motorcraft 2 prong door jamb switch 3/4 inch door jamb mounting holes. Passenger side switch courtesy light switch, for use on 1971-73 Mercury Cougar and Ford Mustang without automatic seat back release option. Has a white button for the switch as shown. Replaces Ford Part #: C8OZ-13713-A.

OEM Motorcraft 2 prong door jamb switch 3/4 inch door jamb mounting holes. Various applications, some for passenger side, some both sides. Replaces Ford Part #: C8OZ-13713-A.

This switch looks very close to original. On close inspection you will notice that there is no Autolite logo and the plastic is not as milky colored as the originals. Sold Individually. Replaces Ford Part #: C8AZ-13713-C.

C9WY-14018-B Left side door ajar switch found on all 1969-70 Mercury Cougar XR7's and part of the Visual Check Panel Package found optionally on Standard Cougars. The visual check panel or "convenience panel" option included the 'door ajar' light.Fits 69 Cougar and XR7Fits 70 Cougar and XR7Fits 69 MustangFits 70 MustangFits 70 Lincoln ContinentalFits 71 Lincoln ContinentalFits 72 Lincoln Continental ...

C9WY-14018-A Right side door ajar switch found on all 1969-70 Mercury Cougar XR7's and part of the Visual Check Panel Package found optionally on Standard Cougars. The visual check panel or "convenience panel" option included the 'door ajar' light.Fits 69 Cougar and XR7Fits 70 Cougar and XR7 Fits 69 MustangFits 70 MustangFits 70 Lincoln ContinentalFits 71 Lincoln ContinentalFits 72 Lincoln Continental ...

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. OEM style door jamb switch to release tilt/tilt-away columns on a 68 or 69 Mercury Cougar or Ford Mustang. Here is an excerpt from the 1967 owners manual: The wheel will swing to the right and up towards the instrument panel whenever the driver opens his door, provided the ignition switch is turned off. When re-entering the vehicle on the drivers side, pull the steering...

68 - 70 Courtesy Light Switches! These replacement switches are an exact reproduction of the original Ford part. This is the 2 pin type. Includes original Autolite Logo. Sold only as a pair. *NOTE* The 1967 uses a smaller pin assembly and this switch will not work without modification. Replaces Ford Part #: C8AZ-13713-C.

This is how most of our taillight panels are cut off. If you only need a partial panel we can do that too, just give us a ring. Keep in mind we only cut panels like this if both 1/4's are ruined. It is getting very hard to come up with some of these cuts. Keep in mind that this is an over sized item and cannot get shipped through USPS, it can only go through UPS. You can expect to pay up to $200 in shipping for this item.

Sold as a pair, these cardboard protectors do more than just give your trunk a clean look, they protect your tail light sockets from damage. If you see them advertised for less we want to know about it!

This RAM AIR hood scoop template was created by placing a piece of butcher paper under an original 1969 428 Cobra Jet RAM AIR hood scoop and applying spray paint to the mounting holes and opening. Contrary to what you may have been told, the opening is not supposed to be round, and yes those protrusions you see are in fact correct. The 1969 uses a slightly different cut out than the 1970.